Niles Audio manual Connect the Keypads, Connect the Slave ZR-6 Multizone Receiver

Page 31

SYSTEM INSTALLATION

ZR-6 MULTIZONE RECEIVER SYSTEM INSTALLATION

CONNECT THE KEYPADS

Each keypad controls a specifi c zone (except TS-Pro). The RJ-45 terminated CAT-5 cable that runs to each keypad is connected to the ZR-6 MultiZone Receiver’s keypad ports labeled: Zone 1, Zone 2, Zone 3, Zone 4, Zone 5 and Zone 6. The zone port to which each keypad connects defi nes the zone controlled by that keypad and the default zone for TS-Pro. For example: the keypad connected to Zone 1 will always control Zone 1. All RJ-45 terminated CAT-5 cables utilize the T568A wiring convention (Figure 14).

CONNECT THE SLAVE ZR-6 MULTIZONE RECEIVER

Multiple ZR-6 MultiZone Receivers can be combined to create up to an eighteen-zone system. The Expansion ports serially connect the multiple ZR-6 MultiZone Receivers with RJ-45 terminated CAT-5 cables using the T568A wiring convention. One receiver must be designated as the Master, the others as Slave(s). If more than one Slave is used, please note that the expansion out of Slave 2 connects to the expansion in of Slave 1. The expansion out of Slave 1 then connects to the expansion in of the Master. Do not connect more than one Slave directly to a Master. All MicroFlashers for source control must be connected to the Master and not to the Slave, IR from the keypads connected to the Slave will be routed to the Master via the expansion ports.

8= BROWN

7= BROWN/WHITE

6= ORANGE

5= BLUE/WHITE

4= BLUE

3= ORANGE/WHITE

2= GREEN

1= GREEN/WHITE

Figure 14. T568A wire termination

CONNECT THE AM AND FM ANTENNAS

FM DIPOLE ANTENNA

The included FM dipole antenna connects to the female 75-ohm coaxial connector. The antenna is then positioned and mounted for best reception. An antenna must be connected to each ZR-6 MultiZone Receiver chassis in Master/Slave confi gurations.

AM LOOP ANTENNA

The included AM loop antenna connects with its bare-wire ends to the spring-loaded terminals. The antenna is then positioned and mounted for best reception. An antenna must be connected to each ZR-6 MultiZone Receiver chassis in Master/Slave confi gurations.

INPUT 2 OR iPod CASCADE OUT

Figure 15. Connecting AM/FM Antennas to the ZR-6 MultiZone Receiver

CONNECT THE 12V OUTPUTS

The Global 12V output triggers an external device whenever any zone is active. The Zone 4, 5 and 6 12V outputs trigger an external device whenever the respective zone becomes active. A common use would be to turn on a 12V trigger-equipped Niles Systems Integration Amplifi er connected to the pre-amplifi er outputs. The 12V outputs can also be used to trigger a Niles AC-3 Voltage-Triggered AC Power Strip (FG00242) to automate power turn-on and turn-off of connected sources.

(CONTINUED ON NEXT PAGE)

NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373

 

29

Page 30 Page 32
Image 31
Page 30 Page 32
Contents ZR-6 Niles Audio Corporation 1-800-BUY-HIFI Introduction BOX ContentsCongratulations Table of Contents Introduction Level. Doorbell chimes require the DBI-1 Doorbell Interface Features and BenefitsSource for background music while entertaining ZR-6 Multizone Receiver Front Panel System Parts GuideZR-6 Multizone Receiver Programming Panel 17 18 19 20 21 22 23 24 25 26 27 28 ZR-6 Multizone Receiver Rear PanelSystem Parts Guide Room naming TS-PRO Color Touchscreen Controller Sold SeparatelyControl screens for the connected sources Playing devicePlayed source SOLO-6MD WEATHER-RESISTANT Master Keypad Sold SeparatelyZR-6 MultiZone Receiver Accessory Keypad FG01442SOLO-6IR WEATHER-RESISTANT Master Keypad Sold Separately Is onLast KEY Returns to the previous channel Menu Button Displays a menu for the selected source device 8L Learning Remote Control IncludedSTAND-ALONE ZR-6 Multizone Receiver System Wiring DiagramsStand-Alone ZR-6 MultiZone Receiver Balanced Video Output Control ConnectionAdding a VS-6 for video distribution External Control Expansion PortsSource Device Control KeypadsOn Next Expanding to 18 zones. Slave #1 ZR-6 detailed Expanding to 18 zones. Slave #2 ZR-6 detailed Home Theater Sync IR Control InputRS-232 Port Connecting an external RS-232 control systemAdding Additional Keypads to a Zone Keypad Power Value KPVNiles ZR-KE Keypad Expander Preamplifier Outputs Adding AN External Amplifier T0 Zone 4, 512V Trigger Output Doorbell Paging System PagingZR-6 Multizone Receiver System Installation System InstallationConnect a High Output Flasher Connect the External Power AmplifiersConnect the Loudspeakers Connect the Niles IR MicroflashersConnect the 12V Outputs Connect the KeypadsConnect the Slave ZR-6 Multizone Receiver Connect the AM and FM AntennasIR Input Connect the Main Power CableConnect the HT Home Theater Sync if Needed Connect the External ControllerSOLO-6IR Keypad InstallationGuidelines Choose a Mounting LocationSOLO-6MD Install the SOLO-6IR Master KeysConnect the CAT-5 Cable to the Keypad Install the Keypads Into Junction BoxesInstalling Keypads in WET Areas NUMERIC-6PTS-PRO Touchscreen InstallationConfiguring the ZR-6 Multizone Receiver System ConfigurationTech TIP Paging Party or Whole House ModeMaximum Volume Level Mode VolumeDisplay This must be confi gured on each slave as well as the master Zone 4 PRE-OUTZone 5 PRE-OUT Zone 6 PRE-OUTNaming the Source Devices Erasing Tuner Preset InformationIR Programming Programming Source Device IR Command CodesConsiderations All zones should be off before entering programming modeProgramming SOLO-6MD and SOLO-6IR Command Code Mapping Chart Device Code Button on Keypad DVD Programming TS-PRO Command Code Mapping Chart DVR SAT TV Fixed Device Codes Programming R-8L IR Command Code Mapping ChartBe Play To Learn Source Device CommandsStoring IR Commands in Library Storing IR Commands in VS-6/LIBRARYBuilding IR Sequences for Source Devices Editing or Erasing Individual IR CommandsTo edit or erase the Power On Command IR Program Editing and ErasingErasing IR and Sequence Programming for ALL Sources Erasing Individual Device SequencesDisplay will show Erase ALL IR+SEQ SRC 3 -/NO +/YES Archiving and or Updating the ZR-6 Multizone Receiver System ARCHIVING/UPDATINGUpdating the ZR-6 Multizone Receiver Firmware Setting UP the AM/FM Tuner System SettingsTo Store Presets in the Tuner Bass Adjustment Setting UP the Zone KeypadsSource Device Level Adjustment Zone Turn on Volume LevelIR Sensor ON/OFF Treble AdjustmentKeypad Setup SOLO-6MD KeypadRelease the button when the confi guration screen appears Audio SettingsDisplay Settings Keypad ConfigurationPress Play/Pause/Select to store the new setting Source Level AdjustmentZone TURN-ON Volume Last Volume or Pre Set VolumeTS-PRO Touchscreen Keypad SetupAudio Settings Display SettingsCustom Image Display Radio Preset NamesSaving a Preset Radio Station Virtual Room TimeoutCustom Image Display Keypad ConfigurationSource Level Adjustment Screen CalibrationRoom Names Zone TURN-ON VolumeTo set the zone turn-on volume Programming the RemoteSearching for a Code Programming the R-8L HAND-HELD Learning Remote ControlConfiguring the TV and AUX Devices Installing the BatteriesProgramming a Learning Button PrecautionsIf the R-8L remote was set up using the procedure from Programming Sources 2, 3, 4, 5,Erasing a Single Learned Button Restoring ALL Button Functions To Factory SettingsProgramming a Sequence From the SOLO-6IR Keypad Operating the ZR-6 Multizone ReceiverAdditional Radio Functions From a SOLO-6IR with NUMERIC-6P Accessory KeypadNUMERIC-6P Accessory Keypad MiscellaneousRemains for 3 seconds after the key is released When a source’s Now Playing screen is displayed, the VolFrom the SOLO-6MD Keypad Selecting a SourceSoft keys to Direct Tuning a Radio StationAll menu items that don’t begin with a letter, e.g Tears If necessary, pressParty WHOLE-HOUSE Mode Operating a Listening Zone From the TS-PRO TouchscreenPress-and-hold the Off key to turn the entire system off Play the AM/FM Tuner From the R-8L Learning Remote ControlPlay Sources Solution TroubleshootingTroubleshooting ProblemLED blinks one long blink while in Setup mode Zone does not turn on when in the Party ModeZone does not turn on when in the Paging Mode LED does not blink when you press a keyLCD Panel Message ZR-6 Error CodesSpecifications Communication Parameters Control Command StringsHardware Configuration RS-232 Control ProtocolsIndicates the command type source Command zsc,3,01cr selects the tuner in zoneCommand Transport commandSyc = system command Zsc = zone specific command Znc = zone commandCommand supports hold function Codes for ZR-6 Specific CommandsRecord 144 Shuffle Group Disc Favorites 126 Down 127 Appendix a Source Device Screen Library Niles Audio Corporation 1-800-BUY-HIFI Appendix a Source Device Screen Library Appendix a Source Device Screen Library Appendix a Source Device Screen Library Appendix a Source Device Screen Library Appendix a Source Device Screen Library Appendix a Source Device Screen Library Appendix a Source Device Screen Library Stored IR Sequence Radio IR Programming WorksheetsStored IR Sequence Source Niles Remote Source Function Button Stored IR Commands SourceIR Programming Worksheets IR Programming Worksheets IR Programming Worksheets IR Programming Worksheets IR Programming Worksheets IR Programming Worksheets IR Programming Worksheets IR Programming Worksheets Source Function Stored IR Commands Library100 Stored IR Commands Library 2/VS-6101 L e s a u d i o C o r p o r a t i o n
Related manuals
Manual 2 pages 6.51 Kb Manual 8 pages 28.43 Kb

ZR-6 specifications

Niles Audio ZR-6 is an innovative, multi-zone audio distribution amplifier that has been specifically designed for whole-home audio systems. With its remarkable features and advanced technologies, the ZR-6 enables users to enjoy high-quality audio throughout their living space while maintaining ease of control and flexibility.

One of the standout features of the Niles ZR-6 is its capability to serve up to six independent zones, allowing users to customize their audio experience in multiple rooms simultaneously. Each zone can be independently controlled, giving users the freedom to select different sources or adjust volume levels according to their preferences. This makes it an exceptional choice for homeowners seeking a tailored listening experience in various areas of their house.

The ZR-6 incorporates advanced digital signal processing and amplification technologies, which enhance sound quality while ensuring the device operates efficiently. With robust amplification and low distortion rates, this amplifier delivers clear and powerful audio. The unit supports up to 100 watts per channel, providing sufficient power to drive a variety of speakers in each zone, resulting in dynamic and engaging sound performance.

Another significant feature of the ZR-6 is its flexible connectivity options. The amplifier includes multiple audio source inputs, such as analog, digital, and network streaming capabilities, making it easy to integrate with existing audio systems or expand into new media sources. This versatility allows users to enjoy music from different platforms, whether it's vinyl records, streaming services, or traditional broadcast radio.

A defining characteristic of the Niles ZR-6 is its user-friendly interface. The control options range from physical keypads to smartphone apps, enabling seamless operation for users of all abilities. Additionally, it supports third-party control systems, making it an ideal choice for advanced home automation setups.

To ensure reliability and longevity, the ZR-6 is built with high-quality components and a durable design. This makes it capable of withstanding the demands of continuous use while delivering superior performance across various audio applications.

In summary, the Niles Audio ZR-6 is a versatile multi-zone audio distribution amplifier that brings together powerful amplification, flexible connectivity, and user-friendly controls. With its advanced technologies and robust features, it stands as an exceptional choice for anyone looking to enhance their home audio experience.
Top Page Image Contents