Niles Audio iC2 manual Flasher Volt, RS232 Video Synch

Page 14

SYSTEM CONFIGURATION 2

DUAL TV MODE AND INTEGRATION WITH AN IR CONTROLLED MULTIZONE RECEIVER

Flat Panel Display

HT Receiver

Portable Docking Station

12 V DC

Power

Supply

Projector

Motorized Projection Screen

RS232 Controllable

Listing System

 

 

 

RF ZigBee Antenna

 

 

HT-MSU

 

Multizone Receiver with IR Interface

CS12V

 

 

 

 

See Figure 7

 

 

iC2 Remote

 

 

 

 

 

DVD Player

 

Flasher

 

 

 

12 Volt

 

 

TiVo®

RS232

 

 

Video Synch

Figure 6. System Configuration 2

 

 

 

System Configuration #2 (Figure 6) demonstrates the Dual TV Mode feature of the iC2 System. The flat panel TV is controlled via RS232 on the HT-MSU RS232 TV/7 port. This is considered the default TV. The customer also has a projector and screen used only when the theater room is dark. The projector is configured (programmed) with Niles QuickConfig Software to be TV2 and is wired for IR control to the HT-MSU IR SRC1 port. The Status of TV2 is connected to the HT-MSU IR SRC1 RCA connection using the 12V output of the projector (usually used to trigger the screen). The projection screen is being triggered by the HT-MSU 12V Output #3. When the first Master Key on the iC2 Remote is pressed from an all off mode, the default TV (the flat panel TV, TV1) is turned on. Master Key 8 is labeled SWAP TV. When the SWAP TV Master Key is pressed, TV1 (flat panel) is turned off and TV2 (the projector) is turned on, and the screen is lowered for viewing. The Dual TV Feature is not limited to IR controllable TVs. Either TV can be RS232 controllable.

NOTE: IN DUAL TV MODE, ONLY ONE TV IS ON AT A TIME. BOTH TVS CANNOT BE ON AT THE SAME TIME.

12

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Page Table of Contents CongratulationsIntroduction Simple Control of Complex Systems BIG Button Remote with Convenient FeaturesFeatures and Benefits Complete SystemAssignable Relays and 12V Outputs Installation FlexibilityReliable Zigbee RF Communication Intelligent Integration with Multizone SystemsParts Guide ContentsIC2 Remote IC2 Remote Bottom View Home Theater Main System Unit HT-MSU Niles Audio Corporation 1-800-BUY-HIFI System Design Considerations IR Output PortsRS232 Output Ports Source Power Status Connections Plug it into the switched outlet of the receiver, orAssignable 12 Volt Outputs Assignable RelaysSystem Configuration System ConfigurationFlasher Volt RS232 Conductor Video Synch Niles Audio Corporation 1-800-BUY-HIFIFlasher Volt RS232 Video SynchTV Array Mode and Integration with a RFG Antenna Considerations Placement of the HT-MSUInstallation Considerations Use sheetrock screwsTech TIP Wiring ConsiderationsHT-MSU requires several different types of wires runs See the Accessories Section for More Information Programming Preparations and WorksheetPC connection for programming Connect the Charging Power Supply InstallationIC2 Remote Battery StepsSleeve Tip Male Connect Power to the HT-MSU. Check LED, Disconnect PowerRing Connect ALL FlashersConnect ALL Status ConnectConnect Relays Connect the Sensor Cable to IR InputExtend and Mount the Antenna InstallationConnect Antenna Problem Hardware IssuesTroubleshooting SolutionsSource Powering On or Off Incorrectly IR pass-through on HT-MSU Accessories10’ cable with a 3.5mm plug An optional device that can be Used instead of the supplied Accessories25A 12VDC Universal Power Supply FG01407 North America FG01408 InternationalWarranty Two-year limited SpecificationsRF .4-GHz frequency ZigBee wireless mesh technology Sequence capability 450 thirty-two step sequencesLimited Warranty For the Name of Your Nearest Authorized Niles Dealer ContactDr. Miss Mr. Mrs. Ms WarrantyregistrationcardcardWarranty Registration DEPT. P.O. BOX 160818 MIAMI, Florida L e s a u d i o C o r p o r a t i o n
Top Page Image Contents