Niles Audio iC2 Steps, Installation, IC2 Remote Battery, Label the Master Keys on the IC2 Remote

Page 20

INSTALLATION

Before you begin, make sure that all of the cables and wires, as well as the power supply cable will reach the proposed location of the HT-MSU. Mark the cables with labels that describe where the cable originates (rather than which terminal on the HT-MSU it connects to).

STEPS:

1) IC2 REMOTE BATTERY

The iC2 Remote rechargeable battery needs to be connected and charged. The installer needs to remove the battery cover with a Phillips screwdriver. The plug on the battery is keyed and only allows it to be plugged in one way. Plug in the battery and position it in the compartment next to the positioning foam.

2) LABEL THE MASTER KEYS ON THE IC2 REMOTE

The Master Keys on the iC2 Remote can be labeled using the supplied label sheet and plastic key caps. The iC2 worksheets should be filled out prior to labeling the Master Keys. Based on the worksheet, peel off the appropriate label from the sheet and place it on the corresponding Master Key. The plastic key caps are molded with one end rounded and the other flat. Orient the key cap correctly over the Master Key; push the key cap down on the Master Key until it sits flush with the molded portion of the iC2 Remote.

3) CONNECT THE CHARGING POWER SUPPLY

�

��

����������

Figure 13.

iC2 Remote’s 8 custom label Master Keys

The rechargeable battery for the iC2 Remote may still have a charge, but we recommend plugging the iC2 Remote to the charging power supply. The iC2 System comes with two identical power DC power supplies. Choose one of them and plug the outlet-plug end into an unswitched AC outlet. Pass the power cable through the supplied ferrite bead, wrap the cable around the bead twice, leaving the power plug as you clip the bead closed.

Figure 14. Ferrite bead on iC2 Remote power supply cable

18

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Page Table of Contents CongratulationsIntroduction BIG Button Remote with Convenient Features Features and BenefitsSimple Control of Complex Systems Complete SystemInstallation Flexibility Reliable Zigbee RF CommunicationAssignable Relays and 12V Outputs Intelligent Integration with Multizone SystemsParts Guide ContentsIC2 Remote IC2 Remote Bottom View Home Theater Main System Unit HT-MSU Niles Audio Corporation 1-800-BUY-HIFI System Design Considerations IR Output PortsRS232 Output Ports Source Power Status Connections Plug it into the switched outlet of the receiver, orAssignable 12 Volt Outputs Assignable RelaysSystem Configuration Flasher Volt RS232 Conductor Video SynchSystem Configuration Niles Audio Corporation 1-800-BUY-HIFIFlasher Volt RS232 Video SynchTV Array Mode and Integration with a RFG Placement of the HT-MSU Installation ConsiderationsAntenna Considerations Use sheetrock screwsTech TIP Wiring ConsiderationsHT-MSU requires several different types of wires runs See the Accessories Section for More Information Programming Preparations and WorksheetPC connection for programming Installation IC2 Remote BatteryConnect the Charging Power Supply StepsConnect Power to the HT-MSU. Check LED, Disconnect Power RingSleeve Tip Male Connect ALL FlashersConnect ALL Status ConnectConnect Relays Connect the Sensor Cable to IR InputExtend and Mount the Antenna InstallationConnect Antenna Hardware Issues TroubleshootingProblem SolutionsSource Powering On or Off Incorrectly IR pass-through on HT-MSU Accessories10’ cable with a 3.5mm plug Accessories 25A 12VDC Universal Power SupplyAn optional device that can be Used instead of the supplied FG01407 North America FG01408 InternationalSpecifications RF .4-GHz frequency ZigBee wireless mesh technologyWarranty Two-year limited Sequence capability 450 thirty-two step sequencesLimited Warranty For the Name of Your Nearest Authorized Niles Dealer ContactDr. Miss Mr. Mrs. Ms WarrantyregistrationcardcardWarranty Registration DEPT. P.O. BOX 160818 MIAMI, Florida L e s a u d i o C o r p o r a t i o n
Top Page Image Contents