Niles Audio iC2 manual Installation, Connect Antenna, Extend and Mount the Antenna

Page 24

INSTALLATION

11) CONNECT ANTENNA

To attach the RF antenna to the HT-MSU, push the antenna down on the antenna socket of the HT-MSU and twist to the right (you will feel a click or stop when the antenna is completely on).

12) EXTEND AND MOUNT THE ANTENNA

Niles supplies a 10 foot extension cable and antenna bracket for mounting the antenna away from the home theater sources. Make sure the antenna extension cable will reach the antenna mount without snagging or twisting with the other cables needed for the HT-MSU. If you’re mounting the HT-MSU to the back of the metal professional equipment rack that slides-out (for easy access

to the wires), make sure that, when the rack is fully extended, the antenna extension cable will reach without being stretched or pinched when the rack is slid back into place. To attach the antenna extension cable to the HT-MSU, push the connector down on the antenna socket of the HT-MSU and twist to the right (you will feel a click or stop when the connector is completely on).

Use a pencil to mark the location of the antenna bracket. (Figure

19)Then, use two dry-wall screws to attach the antenna bracket to the mounting surface. Unscrew the nut from the antenna end of the antenna extension cable; put the antenna connector end through the hole in the bracket. Attach the nut back on the antenna connector end of the cable to tighten the cable to the bracket. Attach the RF antenna to the connector/wall bracket combo; twist to the right (Figure 20). You will feel a click or stop when the antenna is completely on.

Figure 19.

Vertical alignment of antenna is necessary for optimal reception

Figure 20.

Antenna connection to “L” Bracket

13) CONNECT EXPANSION CAT-5 CABLE

If connecting the HT-MSU to a Niles Radio Frequency Gateway instead of attaching the supplied antenna (SEE THE SYSTEM DESIGN CONSIDERATION SECTION, CONFIGURATION #3), use CAT-5 cable terminated with RJ45 connection plugs. The CAT-5 cable must be terminated using the T568A standard wiring (Figure 21).

14) RE-CONNECT POWER TO THE HT-MSU

1 = GREEN/WHITE

2 = GREEN

3 = ORANGE/WHITE

4 = BLUE

5 = BLUE/WHITE

6 = ORANGE

7 = BROWN/WHITE

8 = BROWN

Figure 21. T568A wire termination

You are now ready to program the Niles iC2 System.

22

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Page Table of Contents CongratulationsIntroduction BIG Button Remote with Convenient Features Features and BenefitsSimple Control of Complex Systems Complete SystemInstallation Flexibility Reliable Zigbee RF CommunicationAssignable Relays and 12V Outputs Intelligent Integration with Multizone SystemsContents IC2 RemoteParts Guide IC2 Remote Bottom View Home Theater Main System Unit HT-MSU Niles Audio Corporation 1-800-BUY-HIFI IR Output Ports RS232 Output PortsSystem Design Considerations Source Power Status Connections Plug it into the switched outlet of the receiver, orAssignable 12 Volt Outputs Assignable RelaysSystem Configuration Flasher Volt RS232 Conductor Video SynchSystem Configuration Niles Audio Corporation 1-800-BUY-HIFIFlasher Volt RS232 Video SynchTV Array Mode and Integration with a RFG Placement of the HT-MSU Installation ConsiderationsAntenna Considerations Use sheetrock screwsWiring Considerations HT-MSU requires several different types of wires runsTech TIP See the Accessories Section for More Information Programming Preparations and WorksheetPC connection for programming Installation IC2 Remote BatteryConnect the Charging Power Supply StepsConnect Power to the HT-MSU. Check LED, Disconnect Power RingSleeve Tip Male Connect ALL FlashersConnect ALL Status ConnectConnect Relays Connect the Sensor Cable to IR InputInstallation Connect AntennaExtend and Mount the Antenna Hardware Issues TroubleshootingProblem SolutionsSource Powering On or Off Incorrectly Accessories 10’ cable with a 3.5mm plugIR pass-through on HT-MSU Accessories 25A 12VDC Universal Power SupplyAn optional device that can be Used instead of the supplied FG01407 North America FG01408 InternationalSpecifications RF .4-GHz frequency ZigBee wireless mesh technologyWarranty Two-year limited Sequence capability 450 thirty-two step sequencesLimited Warranty For the Name of Your Nearest Authorized Niles Dealer ContactWarrantyregistrationcardcard Warranty Registration DEPT. P.O. BOX 160818 MIAMI, FloridaDr. Miss Mr. Mrs. Ms L e s a u d i o C o r p o r a t i o n
Top Page Image Contents