Niles Audio iC2 manual Connect Relays, Connect the Sensor Cable to IR Input

Page 23

The Niles QuickConfig Software is used to assign (program) the functionality of these jacks. The configuration software allows the 12V output to be programmed as follows:

a)Output #1 can be configured to output 12V constantly or momentarily. A momentary output would be used to activate a device that requires a pulse of 12V instead of a constant 12V. The pulse can be programmed for 1, 3 or 5 seconds, then off when activated. The constant mode will output 12V continuously when activated, and no 12V when deactivated.

b)Output #2 can be programmed just like Output #1, but completely independent of output #1.

c)Output #3 configured for constant output only when activated,

but is also completely independent of outputs 1 and 2.

Please refer to the Niles QuickConfig Configuration manual for more information about the 12V output programmability.

9) CONNECT RELAYS

The “Dry Contact Closure” relays use 2-conductor wire to pair either the NO “Normally Open” or NC “Normally Closed” side of the removable connector plug with the “Common”. NO or NC is determined by which device you are triggering. Strip 1/4 inch of the insulation from the end of each wire, and tightly twist the end of each wire until no frayed ends remain. Use a small flathead screwdriver or your fingernail to raise the locking tabs, exposing the holes on the removable connector. Insert each wire into the appropriate hole on the removable connector plug (Figure 17) and snap the locking tab down. To help you, the connector plug is keyed. Insert the smooth side of the connector plug into the smooth side of the socket.

10) CONNECT THE SENSOR CABLE TO IR INPUT

Strip 1/4 inch of the insulation from the end of each wire. Tightly twist the end of each wire until no frayed ends remain. Use a small flathead screwdriver or your fingernail to raise the locking tabs, exposing the holes on the removable connector. Insert each wire into the appropriate hole on the removable connector plug (Figure 18) and snap the locking tab down. To help you, the connector plug is keyed. Insert the smooth side of the connector plug into the smooth side of the socket.

N C N

O O O

R M R

M M M

A O A

L N L

L L

Y

Y

C

O

L

P

O

E

S

N

E

 

 

D

Figure 17. Relay removable connection plug

Figure 18. HT-MSU sensor removable connection plug

NILES AUDIO CORPORATION – 1-800-BUY-HIFI305-238-4373

 

21

 

Image 23
Contents Page Congratulations Table of ContentsIntroduction Complete System BIG Button Remote with Convenient FeaturesFeatures and Benefits Simple Control of Complex SystemsIntelligent Integration with Multizone Systems Installation FlexibilityReliable Zigbee RF Communication Assignable Relays and 12V OutputsParts Guide ContentsIC2 Remote IC2 Remote Bottom View Home Theater Main System Unit HT-MSU Niles Audio Corporation 1-800-BUY-HIFI System Design Considerations IR Output PortsRS232 Output Ports Plug it into the switched outlet of the receiver, or Source Power Status ConnectionsAssignable Relays Assignable 12 Volt OutputsNiles Audio Corporation 1-800-BUY-HIFI System ConfigurationFlasher Volt RS232 Conductor Video Synch System ConfigurationRS232 Video Synch Flasher VoltTV Array Mode and Integration with a RFG Use sheetrock screws Placement of the HT-MSUInstallation Considerations Antenna ConsiderationsTech TIP Wiring ConsiderationsHT-MSU requires several different types of wires runs Programming Preparations and Worksheet See the Accessories Section for More InformationPC connection for programming Steps InstallationIC2 Remote Battery Connect the Charging Power SupplyConnect ALL Flashers Connect Power to the HT-MSU. Check LED, Disconnect PowerRing Sleeve Tip MaleConnect Connect ALL StatusConnect the Sensor Cable to IR Input Connect RelaysExtend and Mount the Antenna InstallationConnect Antenna Solutions Hardware IssuesTroubleshooting ProblemSource Powering On or Off Incorrectly IR pass-through on HT-MSU Accessories10’ cable with a 3.5mm plug FG01407 North America FG01408 International Accessories25A 12VDC Universal Power Supply An optional device that can be Used instead of the suppliedSequence capability 450 thirty-two step sequences SpecificationsRF .4-GHz frequency ZigBee wireless mesh technology Warranty Two-year limitedFor the Name of Your Nearest Authorized Niles Dealer Contact Limited WarrantyDr. Miss Mr. Mrs. Ms WarrantyregistrationcardcardWarranty Registration DEPT. P.O. BOX 160818 MIAMI, Florida L e s a u d i o C o r p o r a t i o n