Hearth and Home Technologies EL42 Series Check Firebox Refractory, Inspect Grate, Glass Cleaning

Page 12

C. Check Firebox Refractory

Frequency: After each ash removal

By: Homeowner

WARNING! Risk of Fire! Inspect ﬁreplace refractory. Crumbling, deteriorated refractory can allow overheating of surrounding materials.

Expansion and contraction will cause minor cracking of the refractory. This is normal. The refractory will require periodic replacement depending on use.

The panels should be replaced if

•Cracks exceed ¼ inch (6 mm) in width,

•Metal is exposed behind the refractory,

•Large pieces of refractory fall out.

D. Inspect Grate

Frequency: After each ash removal

By: Homeowner

Inspect grate for:

•Warping or sagging 1-1/2 in. (38 mm) or more

•Broken welds

•Burn-through of grate bars

For safe operation, replace only with an approved grate from Hearth & Homes Technologies Inc.

E. Glass Cleaning

Frequency: As desired

By: Homeowner

CAUTION! Handle glass assembly with care. Glass is breakable.

•Avoid striking, scratching or slamming glass

•Avoid abrasive cleaners

•DO NOT clean glass while it is hot

Clean glass with a non-abrasive commercially available cleaner or ashes:

•Light deposits

-Use household glass cleaner

•Heavy deposits

-Use wood ash on damp cloth or,

-Use commercial ﬁreplace glass cleaner (consult with your dealer)

12	Heatilator • EL36/EL42 • 4044-132 • Rev V • 11/08

Image 12

Contents Wood Burning Fireplace OperationHot screen/mesh and glass doors will cause burns Fire RiskListing Label Information/Location GrateNumber Table of Contents Installer GuideUser Guide Warranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHeatilator EL36/EL42 4044-132 Rev V 11/08 Listing and Code Approvals Appliance CertiﬁcationNon-Combustible Materials Combustible MaterialsOperating Instructions Your FireplaceHot glass will cause burns Seasoned Wood Starting a FireGrate FirescreenGlass Doors Vented Gas Log Sets & Gas Log LightersOptional Components Clear SpaceWood Fuel Maintainance and Service Chimney Inspection/CleaningDisposal of Ashes Creosote Formation and Need for RemovalGlass Cleaning Check Firebox RefractoryInspect Grate Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionInstaller Guide Getting StartedDesign and Installation Considerations DraftNegative Pressure Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsTools and Supplies Needed Fireplace System RequirementsInspect Fireplace and Components Mm all configurations Framing & ClearancesSelect Fireplace Location Clearances Clearances to Combustible MaterialsFireplace Outside Model # Opening Dimensions Sidewalls/SurroundsFrame the Fireplace Installation of Fireplace Things to ConsiderPosition the Fireplace Place Protective Metal Hearth StripsFt min. from top of uppermost chimney section to air inlet YESInstall Outside Air Kit Outside Air InstallationChimney Assembly Maintain minimum height of chimney above roofChimney Requirements Height of Chimney ComponentsUsing Offsets/Returns ExampleInstall Chimney Air Kit Assemble Chimney SectionsInstall Ceiling Firestops Installing the Ceiling FirestopInstall Attic Insulation Shield Prepare Attic Insulation ShieldComplete Installation Install FlashingFollowing steps should be skipped if using a chase Cut out Hole in RoofChimney Termination Requirements Flat RoofsChase Installations Construct the ChaseGas line holes and other openings should be caulked with Chase should be constructed in the manner of allInstall Fireplace & Chimney Install Chase TopInstall as per Sections 7 Install Termination Cap ST375 Square Termination CapTS345/TS345P Square Termination Cap TCT375 Terra Cotta CapShrouds Radiation ShieldField Constructed Shrouds Open Top Shroud TR342 caps require radiation shieldMailbox Style Shroud radiation shield required Roofed Style Shroud radiation shield requiredFinishing Hearth Extension= 1/k x inches of thickness Refer to .2 for hearth extension insulation alternativesRaised Hearth Extension Framing Minimum betweenNon-combustible Sealant Noncombustible Finishing MaterialsFinishing Material In. Micore or equivilent insulationCombustible Mantel Clearances to Mantels or other Combustibles above FireplaceOutside Di- mensions ModelAccessories Gas Log/Lighter ProvisionWood Burning Inserts Gas Code, Ansi Z223.1Fireplace Dimensions Reference Materials1321 mm 406 mm 1676 mm 508 mm 13 mmID4 Insulated Duct Mm i.d 1067 mm UD4 Uninsulated Duct Air Kit PartsChimney Components Catalog #Effective Outside Height Diameter 10-1/2 121 mm 267 mm 10-1/2 267 mm305 mm 27-3/8 24-5/8 695 mm 625 mm 305 mm 24-5/8 625 mm 787 mm10-7/8 276 mm Service Parts Heatilator EL36/EL42Rev V 11/08 EL42 Contact Information