Hearth and Home Technologies Cyclone-Cust Constructing the Appliance Chase, Clearances

Page 8

B. Constructing the Appliance Chase

A chase is a vertical boxlike structure built to enclose the gas appliance and/or its vent system. Vertical vents that run on the outside of a building may be, but are not re- quired to be, installed inside a chase.

Construction of the chase may vary with the type of build- ing. These instructions are not substitutes for the require- ments of local building codes. Local building codes MUST be checked.

Chases should be constructed in the manner of all out- side walls of the home to prevent cold air drafting prob- lems. The chase should not break the outside building envelope in any manner.

Walls, ceiling, base plate and cantilever floor of the chase should be insulated. Vapor and air infiltration barriers should be installed in the chase as per regional codes for the rest of the home. Additionally, in regions where cold air infiltration may be an issue, the inside surfaces may be sheetrocked and taped for maximum air tightness.

To further prevent drafts, the wall shield and ceiling firestops should be caulked with high temperature caulk to seal gaps. Gas line holes and other openings should

A

B

be caulked with high temp caulk or stuffed with unfaced insulation. If the appliance is being installed on a cement slab, a layer of plywood may be placed underneath to prevent conducting cold up into the room.

C. Clearances

WARNING

Fire Risk.

Odor Risk.

•Install appliance on hard metal or wood surfaces extending full width and depth of appliance.

•Do NOT install appliance directly on carpeting, vinyl, tile or any combustible material other than wood.

WARNING

Fire Risk.

•Construct chase to all clearance specifications in manual.

•Locate and install appliance to all clearance

specifications in manual.

C

ED

F

MAX

G

Clearances to Combustibles

 

A

B

C

D

E

F

G

Inches

42-1/2

0

0

17-1/2

17-1/2

6-3/8

41-3/8*

mm

1080

0

0

445

445

162

1051

*This dimension must be held to +0 inch to -1/2 inch to assure the firestop conceals the connection of the glass tube to the slip section.

Figure 3.2 Clearances to Combustibles

8

Heat & Glo • Cyclone-Cust • 2061-900 Rev. L • 10/08

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Hot glass will cause burns Model Cyclone-CustWhat to do if you smell gas Congratulations Homeowner Reference InformationTable of Contents Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of MassachusettsDesign and Installation Considerations Getting StartedInspect Appliance and Components Tools and Supplies NeededModel Framing and ClearancesSelecting Appliance Location Clearances to Combustibles Inches Constructing the Appliance ChaseClearances Mantel Projections 34-3/841-3/8 +0 to -1/2See .4 for specific clearances Termination LocationsVent Termination Minimum Clearances Alcove Applications Vent Information and Diagrams Vent Table KeyUse of Elbows Measuring StandardsVent Diagrams Top Vent Horizontal Termination One ElbowTwo Elbows VT Min HT MaxTop Vent Horizontal Termination Three Elbows Top Vent Vertical Termination No Elbow Flue RestrictorTop Vent Vertical Termination Three Elbows Vent Clearances and Framing Pipe Clearances to CombustiblesWall Penetration Framing Combustible Wall PenetrationVertical Penetration Framing Installing the Ceiling FirestopInstalling Attic Shield Appliance Preparation Securing and Leveling the ApplianceInstalling Vent Pipe Assembly of Vent SectionsDVP Series Venting Only Assembling Pipe SectionsAssembling Minimum Installations MI Sections Assembling DVP-12A Slip SectionsHorizontal Sections Disassembly of Vent SectionsSecuring the Vent Sections Vertical Sections Heat Shield Requirements for Horizontal Termination Installing Heat Shield and Horizontal Termination CapInstalling the Horizontal Termination Cap Installing Roof Flashing and Vertical Ter- mination Cap Roof Pitch Min. FtAssembling and Installing Storm Collar 18 Assembling the Storm Collar Around the PipeGas Information Fuel ConversionsGas Pressures Gas ConnectionHigh Altitude Installations Recommendation for Wire Electrical InformationOptional Accessories Requirements Connecting to the ApplianceHot Surface Ignition Wiring Finishing Facing MaterialAppliance Setup Clean the ApplianceAccessories Glass Assembly InstallationOperating Instructions Before Lighting ApplianceFinal inspection by Turn off all electric power to the applianceLighting Appliance HSI Ignition After Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Fan Motor Service Maintaining and Servicing ApplianceHeat & Glo Cyclone-Cust 2061-900 Rev. L 10/08 Maintenance Tasks Inspect Maintenance TasksLocation Inches Millimeter Appliance Dimension DiagramReference Materials Vent Components Diagrams DVP vent componentsDVP vent components DVP-HSM-B At Depot Service PartsStocked Valve Assembly CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information

Cyclone-Cust specifications

Hearth and Home Technologies has made significant strides in the realm of home heating with its innovative Cyclone-Cust fireplace technology. Designed for modern living spaces, the Cyclone-Cust combines efficiency, aesthetics, and advanced features, making it a popular choice among homeowners seeking both style and functionality.

One of the standout features of the Cyclone-Cust is its unique combustion system. This fireplace employs a patented cyclone burn technology that ensures a more complete and efficient burn of wood or gas fuels. As a result, it produces less smoke and harmful emissions, making it an environmentally friendly option. The advanced combustion technology also contributes to increased heat output, allowing users to enjoy a warm and cozy environment without the need for excessive fuel consumption.

The Cyclone-Cust is engineered with user convenience in mind. Its intuitive control panel allows homeowners to regulate heat output and flame intensity effortlessly. The fireplace can be operated remotely, providing a modern touch that enhances user convenience. Additionally, the unit is equipped with smart technology that can integrate seamlessly with home automation systems. This feature allows users to monitor and control their fireplace from their smartphone or tablet, adding an extra layer of convenience.

Aesthetically, the Cyclone-Cust does not disappoint. It is available in various designs and finishes, allowing homeowners to select an option that complements their interior decor. The striking flame pattern creates a captivating visual experience, serving as a focal point in any living space. Whether you prefer a traditional look or a contemporary style, the Cyclone-Cust can be customized to suit your taste.

Safety is another key characteristic of Hearth and Home Technologies’ Cyclone-Cust fireplaces. The unit is designed with multiple safety features, including glass doors to prevent the accidental escape of sparks and embers. The built-in air wash system helps keep the glass clean, ensuring an unobstructed view of the flames while enhancing safety for families with children or pets.

In summary, the Hearth and Home Technologies Cyclone-Cust fireplace merges efficiency, convenience, safety, and aesthetic appeal into a single unit. Its advanced combustion technology, user-friendly controls, and customizable designs make it a standout option for those looking to enhance their home heating experience. With the Cyclone-Cust, homeowners can enjoy a sophisticated source of warmth that aligns with modern lifestyle demands and environmental considerations.
Top Page Image Contents