Hearth and Home Technologies BE-36-C Framing the Fireplace for DVP-Series and SL D-Series Pipe

Page 12

Step 2. Framing the Fireplace for DVP-Series and SL D-Series Pipe

Fireplace framing can be built before or after the fireplace is set in place. Framing should be positioned to accommo- date wall coverings and fireplace facing material. The dia- gram below shows framing reference dimensions.

CAUTION: MEASURE FIREPLACE DIMENSIONS AND VERIFY FRAMING METHODS AND WALL COVERING DETAILS BEFORE FRAMING.

Framing should be constructed of 2 X 4 lumber or heavier. The framing headers may rest on the

VENTfireplace stand-offs.

FRAMING

HOLE

E D

A B C D* E*

37” 33” 16 1/4” 36 1/2” 24 3/8

*The center of the framing hole is one inch (25.4mm) above the center of the horizontal vent pipe.

WARNING:

To ensure proper clearances the front framing header must be installed on its narrow edge and to the front of the frame.

B

C

A

Figure 3. Framing Dimensions for SL D-Series and DVP-Series Pipe

12

Hearth & Home Technologies • BE-36-C, BE-36-CIPI397-981 Rev. R • 2/05

Image 12
Contents Installers Guide What to do if you smell gasSafety and Warning Information Table of Contents Log Set Assembly BE-36-C, BE-36-CIPICommon Parts / Pièces communes Valve Assembly Intermittent Pilot IgnitionBE-36-C Standing Pilot IgnitionHigh Altitude Installations Installation CodesAppliance Certification CertificationPre-install Preparation Introducing the Hearth & Home Technologies Gas FireplacesANY Such Action MAY Possibly Cause a Fire Hazard Diagram of model BE-36-C Constructing the Fireplace Chase Locating the FireplaceClearance Requirements Framing the Fireplace for DVP-Series and SL D-Series Pipe C D* EInch inner pipe / 6 5/8-inch outer pipe 47 3/434.93mm AT Each Joint Installing the Vent System Identifying Vent ComponentsVent System Approvals Vent System ComponentsFlex Vent Straight UP Vertical VentingUse SL D-Series components only Use DVP-Series Components onlyVenting with One 90 Elbow Use SL D-Series Use DVP-Series Venting with Two 90 ElbowsUse SL D-Series components only Venting with Three 90 elbows + H1 MAX. = 16 4.8m + H + V1 + H1 MAX. = 40 12.2m Venting with Four 90 elbows Go to Install Firestops DVP Series Venting OnlySL-D and SL-Flex Series Venting Only Attach the First Vent Component to the Starting CollarsDVP, SL-D and SL-Flex Series Venting Hole and Vent PipeVent Termination SL-Series Venting OnlyFor DVP Venting Only For All VentingVent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Positioning, Leveling, and Securing the Fireplace Gas Control SystemSecuring of a Fireplace Standing Pilot Ignition SystemGas Supply Line Gas Pressure RequirementsPressure Natural Gas Propane Wiring the Fireplace Valve will be DestroyedRemote Wiring Diagram IPI Intermittent Pilot Ignition IPI Wiring Diagram Installing Trim, Logs, and Ember Material FinishingLET/OUTLET Grilles in ANY Manner Glass Specifications Tempered Placing the Ember MaterialAfter the Installation Double-check for faulty componentsBefore Lighting the Fireplace Lighting the FireplaceFireplace Maintenance Important Turn OFF the GAS Before Servicing Your Fireplace
Related manuals
Manual 65 pages 5.66 Kb

BE-36-C, BE-36-CIPI specifications

Hearth and Home Technologies, a leader in innovative heating solutions, offers two remarkable gas fireplaces: the BE-36-CIPI and BE-36-C. Both models are designed to deliver efficient heating, aesthetic charm, and user-friendly features, making them ideal for modern living spaces.

The BE-36-CIPI is a direct vent fireplace that provides the warmth of a traditional fire without the hassle of wood. One of its most notable features is its contemporary design, featuring clean lines and a wide viewing area. This model comes with an impressive heat output, ensuring that spaces remain comfortably warm during chilly seasons. The BE-36-CIPI incorporates innovative technologies like the IntelliFire™ ignition system, which promotes energy efficiency by providing reliable performance while minimizing fuel consumption.

Moreover, the fireplace's advanced burner system creates a stunning flame pattern and realistic look, enhancing the ambiance of any room. With customizable options, homeowners can choose different media types, such as ceramic logs or contemporary stones, allowing for personal expression in their décor.

On the other hand, the BE-36-C model offers similar features but with its unique twist. This model is characterized by its traditional aesthetic appeal, making it an excellent choice for those who prefer a classic look with modern convenience. The BE-36-C also utilizes the IntelliFire™ system, ensuring efficiency and ease of use. With a versatile design, this fireplace can fit into various style preferences, from rustic to modern.

Both models come equipped with optional heat management systems, allowing for effective temperature regulation. This feature is particularly useful for maintaining a comfortable environment without overheating the space. The fireplaces are also designed with safety in mind, adhering to strict safety standards and offering numerous safety features like a safety pilot and tempered glass doors.

In conclusion, Hearth and Home Technologies’ BE-36-CIPI and BE-36-C gas fireplaces present an ideal blend of aesthetics, efficiency, and advanced technology. Whether opting for the contemporary style of the BE-36-CIPI or the classic allure of the BE-36-C, homeowners are guaranteed to enjoy a superior heating experience that complements their home’s design while providing warmth and comfort.