Hearth and Home Technologies BE-36-C manual Before Lighting the Fireplace, After the Installation

Page 36

Step 11. Before Lighting the Fireplace

Before lighting the fireplace, be sure to do the following:

Remove all paperwork from underneath the fireplace.

Review safety warnings and cautions

•Read the Safety and Warning Information section at the beginning of this Installers Guide.

Double-check for gas leaks

•Before lighting the fireplace, double-check the unit for possible gas leaks.

Double-check vent terminations and front grilles for obstructions.

•Before lighting the fireplace, double-check the unit for possible obstructions that could be blocking the vent ter- minations or the front grilles.

Double-check for faulty components

•Any component that is found to be faulty MUST BE re- placed with an approved component. Tampering with the fireplacecomponentsisDANGEROUSandvoidsallwarranties.

A small amount of air will be in the gas supply lines. When first lighting the fireplace, it will take a few minutes for the lines to purge themselves of this air. Once the purging is complete, the fireplace will light and will operate normally.

Subsequent lightings of the fireplace will not require this purging of air from the gas supply lines, unless the gas valve has been turned to the OFF position, in which case the air would have to be purged.

NOTE: The fireplace should be run 3 to 4 hours on the initial start-up. Turn it off and let it cool completely. Remove and clean the glass. Replace the glass and run the fireplace for an additional 8 hours. This will help to cure the products used in the paint and logs.

During this break-in period it is recommended that some windows in the house be opened for air circulation. This will help avoid setting off smoke detectors, and help eliminate any odors associated with the fireplace’s initial burning.

Step 12. Lighting the Fireplace

You’ve reviewed all safety warnings, you’ve checked the fireplace for gas leaks, you know the vent system is unobstructed, and you’ve checked for faulty components. Now you’re ready to light the fireplace.

!WARNING: PLEASE REFER TO THE LIGHTING CARD FOR ALL CAUTIONS, SAFETY, AND

WARNING INFORMATION PERTAINING TO THE LIGHTING AND OPERATION OF THE FIREPLACE.

After the Installation

!LEAVE THIS INSTALLATION MANUAL WITH THE APPLIANCE FOR FUTURE REFERENCE.

Lava Rock

NOTE: There is more Lava Rock supplied than actually needed, save any extra for future use. DO NOT place any Lava Rock below or behind burner assembly or on the burner. Doing so could cause sooting or delayed ignition. Pour the Lava Rock from the plastic bag in front and to the left and right of the burner assembly.

36

Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. R • 2/05

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Installers Guide What to do if you smell gasSafety and Warning Information Table of Contents Log Set Assembly BE-36-C, BE-36-CIPICommon Parts / Pièces communes Valve Assembly Intermittent Pilot IgnitionBE-36-C Standing Pilot IgnitionHigh Altitude Installations Installation CodesAppliance Certification CertificationPre-install Preparation Introducing the Hearth & Home Technologies Gas FireplacesANY Such Action MAY Possibly Cause a Fire Hazard Diagram of model BE-36-C Constructing the Fireplace Chase Locating the FireplaceClearance Requirements Framing the Fireplace for DVP-Series and SL D-Series Pipe C D* EInch inner pipe / 6 5/8-inch outer pipe 47 3/434.93mm AT Each Joint Installing the Vent System Identifying Vent ComponentsVent System Approvals Vent System ComponentsFlex Vent Straight UP Vertical VentingUse SL D-Series components only Use DVP-Series Components onlyVenting with One 90 Elbow Use SL D-Series Use DVP-Series Venting with Two 90 ElbowsUse SL D-Series components only Venting with Three 90 elbows + H1 MAX. = 16 4.8m + H + V1 + H1 MAX. = 40 12.2m Venting with Four 90 elbows Go to Install Firestops DVP Series Venting OnlySL-D and SL-Flex Series Venting Only Attach the First Vent Component to the Starting CollarsDVP, SL-D and SL-Flex Series Venting Hole and Vent PipeVent Termination SL-Series Venting OnlyFor DVP Venting Only For All VentingVent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Positioning, Leveling, and Securing the Fireplace Gas Control SystemSecuring of a Fireplace Standing Pilot Ignition SystemGas Supply Line Gas Pressure RequirementsPressure Natural Gas Propane Wiring the Fireplace Valve will be DestroyedRemote Wiring Diagram IPI Intermittent Pilot Ignition IPI Wiring Diagram Installing Trim, Logs, and Ember Material FinishingLET/OUTLET Grilles in ANY Manner Glass Specifications Tempered Placing the Ember MaterialAfter the Installation Double-check for faulty componentsBefore Lighting the Fireplace Lighting the FireplaceFireplace Maintenance Important Turn OFF the GAS Before Servicing Your Fireplace
Related manuals
Manual 65 pages 5.66 Kb

BE-36-C, BE-36-CIPI specifications

Hearth and Home Technologies, a leader in innovative heating solutions, offers two remarkable gas fireplaces: the BE-36-CIPI and BE-36-C. Both models are designed to deliver efficient heating, aesthetic charm, and user-friendly features, making them ideal for modern living spaces.

The BE-36-CIPI is a direct vent fireplace that provides the warmth of a traditional fire without the hassle of wood. One of its most notable features is its contemporary design, featuring clean lines and a wide viewing area. This model comes with an impressive heat output, ensuring that spaces remain comfortably warm during chilly seasons. The BE-36-CIPI incorporates innovative technologies like the IntelliFire™ ignition system, which promotes energy efficiency by providing reliable performance while minimizing fuel consumption.

Moreover, the fireplace's advanced burner system creates a stunning flame pattern and realistic look, enhancing the ambiance of any room. With customizable options, homeowners can choose different media types, such as ceramic logs or contemporary stones, allowing for personal expression in their décor.

On the other hand, the BE-36-C model offers similar features but with its unique twist. This model is characterized by its traditional aesthetic appeal, making it an excellent choice for those who prefer a classic look with modern convenience. The BE-36-C also utilizes the IntelliFire™ system, ensuring efficiency and ease of use. With a versatile design, this fireplace can fit into various style preferences, from rustic to modern.

Both models come equipped with optional heat management systems, allowing for effective temperature regulation. This feature is particularly useful for maintaining a comfortable environment without overheating the space. The fireplaces are also designed with safety in mind, adhering to strict safety standards and offering numerous safety features like a safety pilot and tempered glass doors.

In conclusion, Hearth and Home Technologies’ BE-36-CIPI and BE-36-C gas fireplaces present an ideal blend of aesthetics, efficiency, and advanced technology. Whether opting for the contemporary style of the BE-36-CIPI or the classic allure of the BE-36-C, homeowners are guaranteed to enjoy a superior heating experience that complements their home’s design while providing warmth and comfort.
Top Page Image Contents