Hearth and Home Technologies BE-36-C Vent Termination, SL-Series Venting Only, For All Venting

Page 26

If the area above the ceiling is NOT an attic, position and secure the ceiling firestop on the ceiling side of the previously cut and framed hole.

JOIST

CEILING

NAILS (3 REQUIRED)

CEILING FIRESTOP

Figure 23. Ceiling Firestop (Ceiling Side)

If the area above the ceiling IS an attic, position and secure the firestop on top of the previously framed hole.

NOTE: Keep insulation away from the vent pipe at least 1 inch (25mm).

NAILS (3 REQUIRED)

 

RAFTER

CEILING

CEILING FIRESTOP

Figure 24.

Attic Firestop

C.Vent Termination

SL-Series Venting Only:

For Horizontal Terminations - To attach and secure the termination to the last section of horizontal vent:

•Rotate and interlock the ends as described at the begin- ning of the Installing Vent Components section.

•The termination kit should pass through the wall firestops from the exterior of the building.

•Adjust the termination cap to its final exterior position on the building.

For trapezoidal cap termination kits:

•Using screws secure the cap to the exterior wall through the flanges in the cap.

For DVP Venting Only:

Refer to Cinch Pipe and Termination Cap installation in- structions.

For All Venting:

WARNING: THE TERMINATION CAP MUST ! BE POSITIONED SO THAT THE ARROW IS

POINTING UP.

WARNING:! VENTING TERMINALS SHALL NOT BE RECESSED INTO A WALL OR SIDING. VENT TERMINATION CLEARANCES MUST BE FOL- LOWED TO AVOID FIRE DANGER. SEE VENT TER- MINATION MINIMUM CLEARANCES DIAGRAM ON FOLLOWING PAGE.

7 1/4"

(184mm)

Figure 25. Trapezoid Termination Cap

26

Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. R • 2/05

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Installers Guide What to do if you smell gasSafety and Warning Information Table of Contents Log Set Assembly BE-36-C, BE-36-CIPICommon Parts / Pièces communes Valve Assembly Intermittent Pilot IgnitionBE-36-C Standing Pilot IgnitionAppliance Certification High Altitude InstallationsInstallation Codes CertificationANY Such Action MAY Possibly Cause a Fire Hazard Pre-install PreparationIntroducing the Hearth & Home Technologies Gas Fireplaces Diagram of model BE-36-C Clearance Requirements Constructing the Fireplace ChaseLocating the Fireplace Framing the Fireplace for DVP-Series and SL D-Series Pipe C D* EInch inner pipe / 6 5/8-inch outer pipe 47 3/434.93mm AT Each Joint Vent System Approvals Installing the Vent SystemIdentifying Vent Components Vent System ComponentsUse SL D-Series components only Flex VentStraight UP Vertical Venting Use DVP-Series Components onlyVenting with One 90 Elbow Use SL D-Series Use DVP-Series Venting with Two 90 ElbowsUse SL D-Series components only Venting with Three 90 elbows + H1 MAX. = 16 4.8m + H + V1 + H1 MAX. = 40 12.2m Venting with Four 90 elbows Go to Install Firestops DVP Series Venting OnlySL-D and SL-Flex Series Venting Only Attach the First Vent Component to the Starting CollarsDVP, SL-D and SL-Flex Series Venting Hole and Vent PipeFor DVP Venting Only Vent TerminationSL-Series Venting Only For All VentingVent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Securing of a Fireplace Positioning, Leveling, and Securing the FireplaceGas Control System Standing Pilot Ignition SystemPressure Natural Gas Propane Gas Supply LineGas Pressure Requirements Wiring the Fireplace Valve will be DestroyedRemote Wiring Diagram IPI Intermittent Pilot Ignition IPI Wiring Diagram LET/OUTLET Grilles in ANY Manner Installing Trim, Logs, and Ember MaterialFinishing Glass Specifications Tempered Placing the Ember MaterialBefore Lighting the Fireplace After the InstallationDouble-check for faulty components Lighting the FireplaceFireplace Maintenance Important Turn OFF the GAS Before Servicing Your Fireplace
Related manuals
Manual 65 pages 5.66 Kb

BE-36-C, BE-36-CIPI specifications

Hearth and Home Technologies, a leader in innovative heating solutions, offers two remarkable gas fireplaces: the BE-36-CIPI and BE-36-C. Both models are designed to deliver efficient heating, aesthetic charm, and user-friendly features, making them ideal for modern living spaces.

The BE-36-CIPI is a direct vent fireplace that provides the warmth of a traditional fire without the hassle of wood. One of its most notable features is its contemporary design, featuring clean lines and a wide viewing area. This model comes with an impressive heat output, ensuring that spaces remain comfortably warm during chilly seasons. The BE-36-CIPI incorporates innovative technologies like the IntelliFire™ ignition system, which promotes energy efficiency by providing reliable performance while minimizing fuel consumption.

Moreover, the fireplace's advanced burner system creates a stunning flame pattern and realistic look, enhancing the ambiance of any room. With customizable options, homeowners can choose different media types, such as ceramic logs or contemporary stones, allowing for personal expression in their décor.

On the other hand, the BE-36-C model offers similar features but with its unique twist. This model is characterized by its traditional aesthetic appeal, making it an excellent choice for those who prefer a classic look with modern convenience. The BE-36-C also utilizes the IntelliFire™ system, ensuring efficiency and ease of use. With a versatile design, this fireplace can fit into various style preferences, from rustic to modern.

Both models come equipped with optional heat management systems, allowing for effective temperature regulation. This feature is particularly useful for maintaining a comfortable environment without overheating the space. The fireplaces are also designed with safety in mind, adhering to strict safety standards and offering numerous safety features like a safety pilot and tempered glass doors.

In conclusion, Hearth and Home Technologies’ BE-36-CIPI and BE-36-C gas fireplaces present an ideal blend of aesthetics, efficiency, and advanced technology. Whether opting for the contemporary style of the BE-36-CIPI or the classic allure of the BE-36-C, homeowners are guaranteed to enjoy a superior heating experience that complements their home’s design while providing warmth and comfort.
Top Page Image Contents