Hearth and Home Technologies BE-36-CIPI manual Venting with One 90 Elbow Use SL D-Series

Page 17

V

 

H

1' MIN. (305mm)

2'

MAX. (610mm)

2' MIN. (610mm)

4'

MAX. (1.22m)

3' MIN. (914mm)

6'

MAX. (1.86m)

4' MIN. (1.22m)

8'

MAX. (2.4m)

V+H=40' MAX. (12.4m)

H = 8' MAX. (2.4m)

V

Use DVP-Series

components only.

H

Figure 10. Venting with One 90° Elbow

NOTE: There MUST be a 25% reduc- tion in total H when using flex vent except when using the simple up and out installation (see Figure 7).

 

H

Use SL D-Series

V

components only.

 

BE-36-C

 

 

BE-36-C LP

V (MIN.)

H (MAX.)

 

 

H (MAX.)

90o Elbow on Top

2.5' (863mm)

 

2.5' (863mm)

1' (305mm)

3' (914mm)

 

2.5' (863mm)

2' (610mm)

4' (1.22m)

 

4' (1.22m)

3' (914mm)

6' (1.86m)

 

6' (1.86m)

4' (1.22m)

8' (2.48m)

 

8' (2.48m)

5' (1.52m)

16' (4.8m)

 

16' (4.8m)

HMAX. = 16' (4.8m) V + H MAX. = 40' (12.2m)

Figure 11. Venting with One 90° Elbow

Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. R • 2/05

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents What to do if you smell gas Installers GuideSafety and Warning Information Table of Contents BE-36-C, BE-36-CIPI Log Set AssemblyCommon Parts / Pièces communes Intermittent Pilot Ignition Valve AssemblyStanding Pilot Ignition BE-36-CInstallation Codes High Altitude InstallationsAppliance Certification CertificationANY Such Action MAY Possibly Cause a Fire Hazard Pre-install PreparationIntroducing the Hearth & Home Technologies Gas Fireplaces Diagram of model BE-36-C Clearance Requirements Constructing the Fireplace ChaseLocating the Fireplace C D* E Framing the Fireplace for DVP-Series and SL D-Series Pipe47 3/4 Inch inner pipe / 6 5/8-inch outer pipe34.93mm AT Each Joint Identifying Vent Components Installing the Vent SystemVent System Approvals Vent System ComponentsStraight UP Vertical Venting Flex VentUse SL D-Series components only Use DVP-Series Components onlyVenting with One 90 Elbow Use SL D-Series Venting with Two 90 Elbows Use DVP-SeriesUse SL D-Series components only Venting with Three 90 elbows + H1 MAX. = 16 4.8m + H + V1 + H1 MAX. = 40 12.2m Venting with Four 90 elbows DVP Series Venting Only Go to Install FirestopsAttach the First Vent Component to the Starting Collars SL-D and SL-Flex Series Venting OnlyHole and Vent Pipe DVP, SL-D and SL-Flex Series VentingSL-Series Venting Only Vent TerminationFor DVP Venting Only For All VentingVent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Gas Control System Positioning, Leveling, and Securing the FireplaceSecuring of a Fireplace Standing Pilot Ignition SystemPressure Natural Gas Propane Gas Supply LineGas Pressure Requirements Valve will be Destroyed Wiring the FireplaceRemote Wiring Diagram IPI Intermittent Pilot Ignition IPI Wiring Diagram LET/OUTLET Grilles in ANY Manner Installing Trim, Logs, and Ember MaterialFinishing Placing the Ember Material Glass Specifications TemperedDouble-check for faulty components After the InstallationBefore Lighting the Fireplace Lighting the FireplaceImportant Turn OFF the GAS Before Servicing Your Fireplace Fireplace Maintenance
Related manuals
Manual 65 pages 5.66 Kb

BE-36-C, BE-36-CIPI specifications

Hearth and Home Technologies, a leader in innovative heating solutions, offers two remarkable gas fireplaces: the BE-36-CIPI and BE-36-C. Both models are designed to deliver efficient heating, aesthetic charm, and user-friendly features, making them ideal for modern living spaces.

The BE-36-CIPI is a direct vent fireplace that provides the warmth of a traditional fire without the hassle of wood. One of its most notable features is its contemporary design, featuring clean lines and a wide viewing area. This model comes with an impressive heat output, ensuring that spaces remain comfortably warm during chilly seasons. The BE-36-CIPI incorporates innovative technologies like the IntelliFire™ ignition system, which promotes energy efficiency by providing reliable performance while minimizing fuel consumption.

Moreover, the fireplace's advanced burner system creates a stunning flame pattern and realistic look, enhancing the ambiance of any room. With customizable options, homeowners can choose different media types, such as ceramic logs or contemporary stones, allowing for personal expression in their décor.

On the other hand, the BE-36-C model offers similar features but with its unique twist. This model is characterized by its traditional aesthetic appeal, making it an excellent choice for those who prefer a classic look with modern convenience. The BE-36-C also utilizes the IntelliFire™ system, ensuring efficiency and ease of use. With a versatile design, this fireplace can fit into various style preferences, from rustic to modern.

Both models come equipped with optional heat management systems, allowing for effective temperature regulation. This feature is particularly useful for maintaining a comfortable environment without overheating the space. The fireplaces are also designed with safety in mind, adhering to strict safety standards and offering numerous safety features like a safety pilot and tempered glass doors.

In conclusion, Hearth and Home Technologies’ BE-36-CIPI and BE-36-C gas fireplaces present an ideal blend of aesthetics, efficiency, and advanced technology. Whether opting for the contemporary style of the BE-36-CIPI or the classic allure of the BE-36-C, homeowners are guaranteed to enjoy a superior heating experience that complements their home’s design while providing warmth and comfort.
Top Page Image Contents