Hearth and Home Technologies BE-36-CIPI manual Flex Vent, Straight UP Vertical Venting

Page 16

Flex Vent

The flex vent must be supported with the spacing between support intervals not exceeding 4 feet, with no more than ½ inch sag between supports.

A support is required at each change in venting direction, and in any location where it is necessary to maintain the necessary clearance to combustibles. A simple “up and out” installation (Figure 7) requires only enough support to main- tain the necessary clearance to combustibles. However, the vent attachment point and the firestop location are consid- ered to be supports.

CAP

STRAIGHT UP

 

VERTICAL VENTING

 

V (FT.)

 

45' MAX.

V

 

3” CLEARANCE

FLEX-VENT

TERMINATION

CAP

1”

CLEARANCE

NOTE: For vertical venting over 20 feet an Extended Vertical Baffle Kit is recommended for improved flame appearance.

Use SL D-Series components only.

Figure 7.

Figure 8. Straight up Vertical Venting

STRAIGHT OUT HORIZONTAL VENTING

H

Max. Run

36" (914 mm)

Use DVP-Series

components only.

90-DEGREE ELBOWS

For corner installation.

Two 900 elbows or one 450 elbow may be used for corner installations. The use of two 900 elbows in a corner installation will affect space requirements (see Fig. 2)

45-DEGREE

ELBOW

H

Figure 9. Straight Out Horizontal Venting

16

Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. R • 2/05

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Installers Guide What to do if you smell gasSafety and Warning Information Table of Contents Log Set Assembly BE-36-C, BE-36-CIPICommon Parts / Pièces communes Valve Assembly Intermittent Pilot IgnitionBE-36-C Standing Pilot IgnitionHigh Altitude Installations Installation CodesAppliance Certification CertificationIntroducing the Hearth & Home Technologies Gas Fireplaces Pre-install PreparationANY Such Action MAY Possibly Cause a Fire Hazard Diagram of model BE-36-C Locating the Fireplace Constructing the Fireplace ChaseClearance Requirements Framing the Fireplace for DVP-Series and SL D-Series Pipe C D* EInch inner pipe / 6 5/8-inch outer pipe 47 3/434.93mm AT Each Joint Installing the Vent System Identifying Vent ComponentsVent System Approvals Vent System ComponentsFlex Vent Straight UP Vertical VentingUse SL D-Series components only Use DVP-Series Components onlyVenting with One 90 Elbow Use SL D-Series Use DVP-Series Venting with Two 90 ElbowsUse SL D-Series components only Venting with Three 90 elbows + H1 MAX. = 16 4.8m + H + V1 + H1 MAX. = 40 12.2m Venting with Four 90 elbows Go to Install Firestops DVP Series Venting OnlySL-D and SL-Flex Series Venting Only Attach the First Vent Component to the Starting CollarsDVP, SL-D and SL-Flex Series Venting Hole and Vent PipeVent Termination SL-Series Venting OnlyFor DVP Venting Only For All VentingVent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Positioning, Leveling, and Securing the Fireplace Gas Control SystemSecuring of a Fireplace Standing Pilot Ignition SystemGas Pressure Requirements Gas Supply LinePressure Natural Gas Propane Wiring the Fireplace Valve will be DestroyedRemote Wiring Diagram IPI Intermittent Pilot Ignition IPI Wiring Diagram Finishing Installing Trim, Logs, and Ember MaterialLET/OUTLET Grilles in ANY Manner Glass Specifications Tempered Placing the Ember MaterialAfter the Installation Double-check for faulty componentsBefore Lighting the Fireplace Lighting the FireplaceFireplace Maintenance Important Turn OFF the GAS Before Servicing Your Fireplace
Related manuals
Manual 65 pages 5.66 Kb

BE-36-C, BE-36-CIPI specifications

Hearth and Home Technologies, a leader in innovative heating solutions, offers two remarkable gas fireplaces: the BE-36-CIPI and BE-36-C. Both models are designed to deliver efficient heating, aesthetic charm, and user-friendly features, making them ideal for modern living spaces.

The BE-36-CIPI is a direct vent fireplace that provides the warmth of a traditional fire without the hassle of wood. One of its most notable features is its contemporary design, featuring clean lines and a wide viewing area. This model comes with an impressive heat output, ensuring that spaces remain comfortably warm during chilly seasons. The BE-36-CIPI incorporates innovative technologies like the IntelliFire™ ignition system, which promotes energy efficiency by providing reliable performance while minimizing fuel consumption.

Moreover, the fireplace's advanced burner system creates a stunning flame pattern and realistic look, enhancing the ambiance of any room. With customizable options, homeowners can choose different media types, such as ceramic logs or contemporary stones, allowing for personal expression in their décor.

On the other hand, the BE-36-C model offers similar features but with its unique twist. This model is characterized by its traditional aesthetic appeal, making it an excellent choice for those who prefer a classic look with modern convenience. The BE-36-C also utilizes the IntelliFire™ system, ensuring efficiency and ease of use. With a versatile design, this fireplace can fit into various style preferences, from rustic to modern.

Both models come equipped with optional heat management systems, allowing for effective temperature regulation. This feature is particularly useful for maintaining a comfortable environment without overheating the space. The fireplaces are also designed with safety in mind, adhering to strict safety standards and offering numerous safety features like a safety pilot and tempered glass doors.

In conclusion, Hearth and Home Technologies’ BE-36-CIPI and BE-36-C gas fireplaces present an ideal blend of aesthetics, efficiency, and advanced technology. Whether opting for the contemporary style of the BE-36-CIPI or the classic allure of the BE-36-C, homeowners are guaranteed to enjoy a superior heating experience that complements their home’s design while providing warmth and comfort.
Top Page Image Contents