Hearth and Home Technologies A42RH, A36RH Install Outside Air Kit, Flexible Duct not supplied

Page 23

E. Install Outside Air Kit

•Keep duct runs short and straight to minimize restriction. A small dip is acceptable for a cold air trap.

•The outside air kit must be installed on the left hand side of the fireplace.

•Locate the air inlet in a clear area, preferably into prevailing wind during the heating season. Refer to Figure 5.2.

•Install as shown in Figures 7.3, 7.4 and 7.5.

•The air duct may be run vertically.

•The outside air inlet must be at least 3 ft (.91 m) below the top of the uppermost chimney section.

CAUTION! Risk of Fire or Asphyxiation! DO NOT draw outside combustion air from wall, floor or ceiling cavity, or enclosed spaces such as an attic or garage.

•DO NOT place outside air inlet close to exhaust vents or chimneys. Fumes or odor could be drawn into the room through the fireplace.

•Locate outside air inlet to prevent blockage from leaves, snow/ice, or other debris. Blockages could cause combustion air starvation.

Flexible Duct (not supplied)

 

 

Outside Air

Outside Air

 

Plate

 

Assembly

Hood

2 Wire Ties

 

•Hearth & Home Technologies Inc recommends using UL181 Class 0 or Class I rigid or flexible ducting.

•Secure flex duct with metal tape, screws or wire ties.

Figure 7.5 Outside Air Installation

Heatilator • A36R & A42R • 28376 • Rev AF • 11/08

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Fire Risk Wood Burning FireplaceOperation Hot screen/mesh and glass doors will cause burnsNumber Listing Label Information/LocationGrate User Guide Table of ContentsInstaller Guide CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited WarrantyHeatilator A36R & A42R 28376 Rev AF 11/08 Combustible Materials Listing and Code ApprovalsAppliance Certification Non-Combustible MaterialsHot glass will cause burns Operating InstructionsYour Fireplace Firescreen Seasoned WoodStarting a Fire GrateClear Space Glass DoorsVented Gas Log Sets & Gas Log Lighters Optional ComponentsHardwood vs Softwood Wood FuelDisposal of Ashes Maintainance and ServiceChimney Inspection/Cleaning Frequency As desired Glass CleaningCheck Firebox Refractory Inspect GrateStart Fire Problems Possible Cause Solution Troubleshooting GuideTypical Fireplace System Getting StartedNegative Pressure Design and Installation ConsiderationsDraft Frequently open doors Central heat outlets or returns Locating Fireplace & ChimneyInspect Fireplace and Components Tools and Supplies NeededSelect Fireplace Location Fireplace Dimensions .A 1219 mm MinimumMm all configurations Framing & ClearancesClearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsPlace Protective Metal Hearth Strips Installation of FireplaceThings to Consider Position the FireplaceFt min. from top of uppermost chimney section to air inlet Flexible Duct not supplied Install Outside Air KitHood Wire Ties Secure flex duct with metal tape, screws or wire tiesMaintain minimum height of chimney above roof Chimney AssemblyHeight of Chimney Components Chimney RequirementsExample Using Offsets/ReturnsAssembling Chimney Sections Install Chimney Air KitInstalling Ceiling Firestops Prepare Attic Insulation Shield Installing Attic Insulation ShieldCut out Hole in Roof Complete InstallationInstall Flashing Flat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsInstall Chase Top Install Fireplace & ChimneyST375 Square Termination Cap Install Termination CapTCT375 Terra Cotta Cap TS345/TS345P Square Termination CapField Constructed Shrouds Some shrouds require a radiation shield. Use where specifiedShrouds Radiation ShieldMailbox Style Shroud radiation shield required = 1/k x inches of thickness FinishingHearth Extension HX3 or HX4 Hearth Ext or equivilent insulation Finishing Material305 mm Combustible MantelWood Burning Inserts AccessoriesInstall Fan Gas Log/Lighter Provision235 mm 594 mm 244 mm 219 mm 206 mm 108 mm 13-1/2 343 mm 222 mm 22-3/4578 mm 10-1/2 165 mm 267 mm Dia 28376 Gas Knockout Rev Outside 23-3/8 AirCatalog # Description Fireplace ComponentsCatalog # Chimney Components305 mm 24-5/8 625 mm 787 mm Effective Outside Height Diameter 10-1/2 121 mm 267 mm10-1/2 267 mm 305 mm 27-3/8 24-5/8 695 mm 625 mm10-7/8 276 mm A36R, A36RH Service PartsA42R, A42RH Contact Information

A36RH, A42RH, A36R, A42R specifications

Hearth and Home Technologies offers a distinguished range of fireplace products to cater to diverse consumer needs, focused on delivering warmth and style to any living space. Among their offerings, the A42R, A36R, A42RH, and A36RH models stand out, each equipped with advanced features and innovative technologies that enhance the overall user experience.

The A42R and A36R are designed specifically for those who appreciate the elegance of traditional fireplaces while also seeking the efficiency and convenience of modern technology. Both models feature a large viewing area, providing an impressive flame display that creates a captivating focal point in any room. The clean face design eliminates the need for a traditional mantel, allowing for more flexible installation options and a contemporary aesthetic that complements various interior styles.

One of the key characteristics of both the A42R and A36R is their advanced combustion technology, which promotes efficient fuel use while minimizing emissions. This ensures that customers can enjoy the comforting warmth of a fire without compromising air quality. Additionally, these models come equipped with a state-of-the-art heat distribution system, ensuring that warmth spreads evenly throughout the room.

The A42RH and A36RH models take the concept of efficiency further by incorporating a high-efficiency rating. With a focus on heat retention, these models are capable of generating substantial warmth that can be comfortably felt in larger spaces. The RH designation indicates a built-in blower system that maximizes heat output and ensures a cozy atmosphere during even the coldest months.

All four models feature easy-to-use controls, allowing homeowners to adjust heat output and flame levels to suit their preferences. This versatility sets them apart from traditional wood-burning fireplaces, offering a more user-friendly experience. Moreover, the fireplaces are engineered with durable materials and quality craftsmanship, ensuring a long-lasting investment for any household.

In summary, Hearth and Home Technologies’ A42R, A36R, A42RH, and A36RH models deliver a perfect blend of elegance, efficiency, and innovation. Their key features, including large viewing areas, advanced combustion technology, and effective heat distribution systems, make them ideal choices for homeowners looking to enhance their living spaces with the joy and comfort of a fireplace. Whether opting for the simpler A42R and A36R or the high-efficiency A42RH and A36RH, consumers can expect both style and functionality in their choice of Hearth and Home Technologies fireplaces.
Top Page Image Contents