Hearth and Home Technologies A36RH, A42R Listing and Code Approvals, Appliance Certification

Page 6

1 Listing and Code Approvals

A. Appliance Certification

This fireplace system has been tested and listed in accor- dance with UL 127 and ULC-S610 standards by Under- writers Laboratories Inc. for installation and operation in the United States and Canada.

This fireplace may be installed in sleeping rooms EX- CEPT in manufactured homes. If installed with a gas log set, provisions for the National Fuel Gas Code must be met.

This fireplace has been tested and listed for use with the optional components specified in this manual. These op- tional components may be purchased separately and in- stalled at a later date. Installation of an outside air kit will require significant reconstruction and is best if installed at the time of fireplace installation.

Heatilator is a registered trademark of Hearth & Home Technologies Inc.

WARNING! Risk of Fire! Hearth & Home Technologies disclaims any responsibility for, and the warranty and agency listing will be voided by the following actions.

DO NOT:

•install or operate damaged fireplace

•modify fireplace

•install other than as instructed by Hearth & Home Technologies

•operate the fireplace without fully assembling all components

•overfire

•install an unvented gas log set

•install any component not approved by Hearth & Home Technologies

•install parts or components not Listed or approved

B. Non-Combustible Materials

•Materials which will not ignite and burn, composed of any combination of the following:

-

Steel

-

Iron

-

Brick

-

Tile

-

Concrete

-

Slate

-

Glass

-

Plasters

•Materials reported as passing ASTM E 136, Standard

Test Method for Behavior of Metals, in a Vertical Tube Furnace at 750° C

C. Combustible Materials

•Materials made of or surfaced with any of the following materials:

-

Wood

-

Compressed paper

-

Plant fibers

-

Plastic

•Any material that can ignite and burn; flame proofed or not, plastered or un-plastered

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information, consult a qualified installer, service agency or your dealer.

NOTICE: This fireplace is tested and approved as a decorative fireplace. It should not be factored as a primary heat source in residential heating calculations.

6

Heatilator • A36R & A42R • 28376 • Rev AF • 11/08

Page 5 Page 7
Image 6
Page 5 Page 7
Contents
Hot screen/mesh and glass doors will cause burns Wood Burning FireplaceOperation Fire RiskListing Label Information/Location GrateNumber Table of Contents Installer GuideUser Guide Warranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHeatilator A36R & A42R 28376 Rev AF 11/08 Non-Combustible Materials Listing and Code ApprovalsAppliance Certification Combustible MaterialsOperating Instructions Your FireplaceHot glass will cause burns Grate Seasoned WoodStarting a Fire FirescreenOptional Components Glass DoorsVented Gas Log Sets & Gas Log Lighters Clear SpaceWood Fuel Hardwood vs SoftwoodMaintainance and Service Chimney Inspection/CleaningDisposal of Ashes Inspect Grate Glass CleaningCheck Firebox Refractory Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemDesign and Installation Considerations DraftNegative Pressure Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsTools and Supplies Needed Inspect Fireplace and ComponentsFraming & Clearances Fireplace Dimensions .A 1219 mm MinimumMm all configurations Select Fireplace LocationClearances Clearances to Combustible MaterialsSidewalls/Surrounds Frame the FireplacePosition the Fireplace Installation of FireplaceThings to Consider Place Protective Metal Hearth StripsFt min. from top of uppermost chimney section to air inlet Secure flex duct with metal tape, screws or wire ties Install Outside Air KitHood Wire Ties Flexible Duct not suppliedChimney Assembly Maintain minimum height of chimney above roofChimney Requirements Height of Chimney ComponentsUsing Offsets/Returns ExampleInstall Chimney Air Kit Installing Ceiling FirestopsAssembling Chimney Sections Installing Attic Insulation Shield Prepare Attic Insulation ShieldComplete Installation Install FlashingCut out Hole in Roof Chimney Termination Requirements Flat RoofsChase Installations Construct the ChaseInstall Fireplace & Chimney Install Chase TopInstall Termination Cap ST375 Square Termination CapTS345/TS345P Square Termination Cap TCT375 Terra Cotta CapRadiation Shield Some shrouds require a radiation shield. Use where specifiedShrouds Field Constructed ShroudsMailbox Style Shroud radiation shield required Finishing Hearth Extension= 1/k x inches of thickness Finishing Material HX3 or HX4 Hearth Ext or equivilent insulationCombustible Mantel 305 mmGas Log/Lighter Provision AccessoriesInstall Fan Wood Burning Inserts165 mm 267 mm Dia 28376 Gas Knockout Rev Outside 23-3/8 Air 222 mm 22-3/4578 mm 10-1/2 235 mm 594 mm 244 mm 219 mm 206 mm 108 mm 13-1/2 343 mmFireplace Components Catalog # DescriptionChimney Components Catalog #305 mm 27-3/8 24-5/8 695 mm 625 mm Effective Outside Height Diameter 10-1/2 121 mm 267 mm10-1/2 267 mm 305 mm 24-5/8 625 mm 787 mm10-7/8 276 mm Service Parts A36R, A36RHA42R, A42RH Contact Information