Hearth and Home Technologies A36R TS345/TS345P Square Termination Cap, TCT375 Terra Cotta Cap

Page 34

•TS345/TS345P Square Termination Cap

Termination Cap

Collar

2 in. (51 mm)

Minimum Height

Chase Top

Chimney

Pipe

Place waterproof sealer under each flange of the termina- tion cap and on top of each screw to help prevent leaks.

3 in. (76 mm)

Maximum

top of chase to top of

chimney section

Chase

Termination cap pipe and chimney section must overlap 1-1/2 in. (38 mm).

Figure 9.7 Installing a TS345/TS345P Square Termination Cap

•TCT375 Terra Cotta Cap

Collar

2 in. (51 mm)

Minimum Height

Chase Top

Place waterproof sealer under each flange of the termina- tion cap and on top of each screw to help prevent leaks.

Termination Cap

The last section of pipe must stop between 2 in. (51 mm) above top of chase and 7 in. (178 mm) below top of chase

2 in. (51 mm)

7 in. (178 mm)

Chase

Chimney

Pipe

Termination cap pipe and chimney section must overlap 1-1/2 in. (38 mm)

Figure 9.8 Installing a TCT375 Terra Cotta Cap

34

Heatilator • A36R & A42R • 28376 • Rev AF • 11/08

Page 33 Page 35
Image 34
Page 33 Page 35
Contents
Hot screen/mesh and glass doors will cause burns Wood Burning FireplaceOperation Fire RiskGrate Listing Label Information/LocationNumber Installer Guide Table of ContentsUser Guide Warranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHeatilator A36R & A42R 28376 Rev AF 11/08 Non-Combustible Materials Listing and Code ApprovalsAppliance Certification Combustible MaterialsYour Fireplace Operating InstructionsHot glass will cause burns Grate Seasoned WoodStarting a Fire FirescreenOptional Components Glass DoorsVented Gas Log Sets & Gas Log Lighters Clear SpaceWood Fuel Hardwood vs SoftwoodChimney Inspection/Cleaning Maintainance and ServiceDisposal of Ashes Inspect Grate Glass CleaningCheck Firebox Refractory Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemDraft Design and Installation ConsiderationsNegative Pressure Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsTools and Supplies Needed Inspect Fireplace and ComponentsFraming & Clearances Fireplace Dimensions .A 1219 mm MinimumMm all configurations Select Fireplace LocationClearances Clearances to Combustible MaterialsSidewalls/Surrounds Frame the FireplacePosition the Fireplace Installation of FireplaceThings to Consider Place Protective Metal Hearth StripsFt min. from top of uppermost chimney section to air inlet Secure flex duct with metal tape, screws or wire ties Install Outside Air KitHood Wire Ties Flexible Duct not suppliedChimney Assembly Maintain minimum height of chimney above roofChimney Requirements Height of Chimney ComponentsUsing Offsets/Returns ExampleInstalling Ceiling Firestops Install Chimney Air KitAssembling Chimney Sections Installing Attic Insulation Shield Prepare Attic Insulation ShieldInstall Flashing Complete InstallationCut out Hole in Roof Chimney Termination Requirements Flat RoofsChase Installations Construct the ChaseInstall Fireplace & Chimney Install Chase TopInstall Termination Cap ST375 Square Termination CapTS345/TS345P Square Termination Cap TCT375 Terra Cotta CapRadiation Shield Some shrouds require a radiation shield. Use where specifiedShrouds Field Constructed ShroudsMailbox Style Shroud radiation shield required Hearth Extension Finishing= 1/k x inches of thickness Finishing Material HX3 or HX4 Hearth Ext or equivilent insulationCombustible Mantel 305 mmGas Log/Lighter Provision AccessoriesInstall Fan Wood Burning Inserts165 mm 267 mm Dia 28376 Gas Knockout Rev Outside 23-3/8 Air 222 mm 22-3/4578 mm 10-1/2 235 mm 594 mm 244 mm 219 mm 206 mm 108 mm 13-1/2 343 mmFireplace Components Catalog # DescriptionChimney Components Catalog #305 mm 27-3/8 24-5/8 695 mm 625 mm Effective Outside Height Diameter 10-1/2 121 mm 267 mm10-1/2 267 mm 305 mm 24-5/8 625 mm 787 mm10-7/8 276 mm Service Parts A36R, A36RHA42R, A42RH Contact Information