Hearth and Home Technologies BC36C Complete the Enclosure, Gas Log/Lighter Provisions

Page 19

BC36C/BC36R INSTALLATION INSTRUCTIONS

14.Complete the Enclosure

Complete the fireplace enclosure, allowing space for outside air ducts and gas piping if desired. Electrical wiring should not come in contact with the fireplace. A minimum clearance of 1 in. must be maintained between the fireplace sides and the enclosure as well as the fireplace back and the enclosure. See pages 10-12 for framing details.

Note: Use only a noncombustible material to fin- ish the face of the fireplace below the level of the front standoffs. A noncombustible material such as USG MICORE CV230 Mineral Fiber Board, or USG DUROCK Cement Board is recommended for this purpose.

CAUTION:

When using a gas log set, the fireplace damper must be set in the fully open position. This en- sures proper venting of combustion products.

15.Gas Log/Lighter Provisions

Knockouts are provided on both sides of the fireplace to allow for connection of a certified gas log lighter or a decorative gas appliance with a maximum input of 100,000 BTU/hour, incorporating an automatic gas shut-off device and complying with the Standard for Decorative Gas Appliances for Installation in Vented Fireplaces, ANSI Z21.60. The decorative gas appliance should be installed in accordance with the National Fuel Gas Code, ANSI Z223.1-1980. The side refractories are designed to allow 1/2 in . iron pipe to pass through. Use a noncombustible sealant to seal any opening between the gas pipe and refractory on the inside. Repack the insulation removed to seal around the gas pipe where it exits the side of the fireplace. A minimum 1-1/2 in. air clearance must be provided around the 1/2 in. iron pipe for a minimum of 4 in. beyond the fireplace. See Figure 16.

This fireplace has been set up for installation of the gas pipe on the right hand side. If it is necessary to plumb the fireplace from the left hand side, remove the gas cover plate and gas tube from the right hand side of the fireplace and install on the left hand side. Cover the hole in the right hand side outershell of the fireplace with the cover plate that covered the gas tube.

Figure 16 - Air Clearance Around Gas Line

CLEARANCES!

A minimum 1 in. air clearance must be maintained at the back and sides of the fireplace assembly ex- cept at the nailing flange where the clearance is 1/2 in.

Chimney sections at any level require a 2 in. mini- mum air space clearance between the framing and chimney section.

WARNING!

This fireplace was not tested by the fireplace manufacturer for use with an unvented gas log heater. To reduce risk of injury, do not install an unvented gas log heater in this fireplace un- less it has been specifically tested and listed by Underwriter’s Laboratories Inc. for use in this specific model fireplace. Unless the unvented gas log heater is tested and listed for use in this factory built fireplace, a fire hazard may be created that can result in a structure fire.

08/04

34962 Rev G

19

Image 19
Contents Installation & Operating Instructions Table of Contents Design and Installation Considerations Description of the Fireplace System Listings and Code ApprovalsFireplace Components System ComponentsBC36C/BC36R Installation Instructions CAK4A Chimney ComponentsCatalog # BC36C/BC36R Installation Instructions Fireplace Locations and Space Requirements PRE-INSTALLATION PreparationFraming the Fireplace Frame the FireplaceSidewalls/Surrounds Chimney RequirementsOffset Chart Using Offsets and ReturnsNumber of Sections Required Chimney Height Requirements above roof lineLevel the Fireplace Installation of FireplacePosition the Fireplace Place the Protective Metal Hearth StripsAssemble the Chimney Sections Install the Firestop SpacersAttic Insulation Shield Double-check the Chimney AssemblySecure the Chimney System Cut out the Hole in the Roof Install the Roof FlashingInstall the Outside Air Kit Mark the Exit Point of the RoofGas Log/Lighter Provisions Complete the EnclosureFactory Built Hearth Extension Hearth ExtensionGlass Doors Position the Hearth ExtensionFinishing Material MantelMaterials Constructing a ChaseTermination Cap Chase TopInstalling an ST375 Square Termination Cap General Information Outside Air Operating InstructionsFlue Damper Firescreen GrateWood Fuel Starting a Fire Draft ProblemsBC36C/BC36R Installation Instructions Creosote and Soot Maintenance InstructionsChimney Cleaning Disposal of Ashes Clear Space Near the FireplaceHOMEOWNER’S Notes Index Hearth & Home Technologies INC. Woodburning Fireplace

BC36C specifications

The Hearth and Home Technologies BC36C is a premium gas fireplace that seamlessly blends comfort, efficiency, and aesthetic appeal. Ideal for residential spaces, this model enhances the ambiance of any room while providing a reliable source of warmth. Its design emphasizes both modern aesthetics and advanced functionality, making it a popular choice among homeowners and interior designers alike.

One of the standout features of the BC36C is its impressive heating capability. With a heat output of up to 30,000 BTUs, this fireplace efficiently warms large areas, ensuring that your space remains cozy even on the coldest nights. The unit’s advanced venting system allows for flexible installation options, whether you prefer traditional venting or direct venting through an exterior wall.

The BC36C is designed with an adjustable flame control feature, allowing users to customize the intensity of the fire to suit their mood or specific heating needs. This not only enhances the user experience but also contributes to energy efficiency. The glass viewing area is expansive, providing an unobstructed view of the flames, while the clean face design minimizes distractions and frames the fire beautifully.

Moreover, the incorporation of advanced technologies such as ProFlame and Eco-Boost systems elevates the fireplace’s performance. The ProFlame technology ensures consistent operation, while the Eco-Boost feature enhances heat output without compromising efficiency. The unit is equipped with a reliable remote control system, granting homeowners the convenience of adjusting settings from across the room.

The BC36C also takes safety seriously. It includes features like the automatic shut-off function and a safety barrier screen, providing peace of mind for families with children or pets. Additionally, the unit’s high-quality construction materials ensure durability and longevity, making it a worthwhile investment for any homeowner.

In terms of aesthetic options, the BC36C comes with various decorative choices, including different media types such as decorative logs, crystals, or stones, allowing you to personalize the look of your fireplace. This versatility ensures that the fireplace complements your interior design style, turning it into a centerpiece of your living space.

In conclusion, the Hearth and Home Technologies BC36C gas fireplace combines cutting-edge technology, efficient heating, and a beautiful design, making it a top choice for anyone looking to add warmth and elegance to their home. With features that prioritize safety, efficiency, and user customization, this fireplace represents a perfect blend of functionality and style.