Hearth and Home Technologies HUDBAY-INS For Your Safety Read Before Lighting, Lighting Appliance

Page 24

B. Lighting Appliance

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may

result causing property damage, personal injury or loss of life

A.This appliance has a pilot that must be lit manually. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING, smell around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS:

*Do not try to light any appliance.

*Do not touch any electric switch, do not use any phone in your building.

*Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

*If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

 

LIGHTING INSTRUCTIONS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.

STOP! Read the safety information above on this label.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2.

Set the thermostat to the lowest setting (if applicable) and turn off

 

 

 

 

 

 

 

 

 

 

the switch at the control panel.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

Disconnect the power from the appliance.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

Open the door of the appliance. May need to remove face/front first.

 

 

 

 

5.

Push in gas control knob slightly and turn clockwise

to the "OFF"

 

 

 

position. Do not force.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6.Wait five (5) minutes to clear out any gas. Smell for gas, including near the floor. If you smell gas, STOP! Follow "B" of the safety information above. If you don't smell gas go to the next step.

7.Push gas control knob in and turn counterclockwise to the pilot position. NOTE: Knob cannot be turned unless knob is pushed in slightly. Do not force.

8.PIEZO IGNITER: Press down on the gas control knob in pilot position and simultaneously press the piezo igniter.

(This may take many repetitions for lighting.)

ELECTRONIC IGNITER: If the unit is equipped with an electronic igniter it should begin sparking right away.

9.The pilot should be visible through the door opening.

10.After the pilot is lit, continue holding control knob down for approximately

30 seconds. Release the knob and it will pop back up. Pilot should remain lit.

MILLIVOLT

PILOT HOOD

THERMOCOUPLE

If it goes out, repeat steps 7 through 9.

GENERATOR

* If the knob does not pop up when released, stop and immediately call your

 

 

service technician or gas supplier.

 

 

* If the pilot will not stay lit after several tries, turn the gas control knob

 

 

clockwise

to "OFF" and call your service technician or gas supplier.

 

 

11. Reinstall door and face. Wait five minutes to allow pilot flame to stabilize and establish proper draft.

12.Push down and turn gas control knob counterclockwise to "ON".

13.Push burner rocker switch on the control panel to "ON". If thermostat is to be used, leave switch in "OFF" position and set the thermostat to desired setting.

14.Reconnect electrical power to appliance.

TO TURN OFF GAS TO APPLIANCE

1.Set the thermostat to lowest setting.

2.Turn off all electric power to the appliance if service is to be performed.

3. Push in gas control knob slightly and turn clockwise

to "OFF" position.

24

Quadra-Fire • Hudson Bay Insert • 7008-115 Rev. H • 10/08

Image 24
Contents What to do if you smell gas HUDBAY-INSDo Discardnot Welcome to the Quadra-Fire Family Table of Contents Listing and Code Approvals Installation to ensure maximum safety and benefit Getting StartedTools and Supplies Needed Read all of the instructions before starting the instaFraming and Clearances Selecting Appliance LocationClearances to Combustibles HearthTermination Locations Vent Termination Minimum ClearancesVenting and Installation Vent InformationExhaust AIR Vent Pipe Termination CAP Adaptor Gas Information Fuel ConversionsConverting to LP Gas Screws Nuts Holding Burner PANValve Regulator Replacement Gas Pressures Gas Connection Check for GAS LeaksRecommendation for Wire Connecting to the ApplianceStanding Pilot Ignition System Wiring Wire Size Max. LengthPilot Appliance Setup AccessoriesDoor Crown Installation Remove Shipping MaterialsGrille Installation Panel Set InstallationBack of TOP Panel Screws Back of Side Panel Brick Installation Retaining TabsPositioning the Logs Rear Brick Retaining TabsBlower Installation Mineral WoolIncluded in kit Blower = 1/4 in mm female spade = 1/4 in mm male spade Air Shutter Adjustment Operating Instructions Before Lighting ApplianceFor Your Safety Read Before Lighting Lighting ApplianceFrequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting Symptom Possible Causes Corrective ActionStanding Pilot Ignition System Troubleshooting Symptom Possible Cause Corrective ActionGlass Replacement Door Frame with Glass Assembly ReplacementMaintaining and Servicing Appliance To Replace Separate Glass PiecesMaintenance Tasks Inspect Necessary. USE Caution When CLEANING/HANDLING Ceramic BurnerAppliance Dimension Diagram Reference MaterialsVent Components List HHTLog Set Assembly Service PartsService Parts List DepotDescription Serial # Part Number Standing Pilot Valve Assembly StockedCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information

HUDBAY-INS specifications

Hearth and Home Technologies (HHT) has consistently set the benchmark in the hearth industry with its innovative products. One of its noteworthy offerings is the HUDBAY-INS, a vent-free gas fireplace insert designed to provide unparalleled comfort and efficiency in home heating. The HUDBAY-INS showcases a blend of modern technology, aesthetic appeal, and user-friendly features that cater to the evolving needs of homeowners.

At the heart of the HUDBAY-INS is its advanced vent-free technology. This allows the fireplace insert to operate without the need for flues or chimneys, resulting in an efficient heating solution that maximizes energy use. Homeowners can enjoy the benefits of a warm, inviting space without the complexities associated with traditional vented models. The vent-free design also simplifies installation, making it a versatile option suitable for various home layouts.

One of the standout features of the HUDBAY-INS is its adjustable flame. Users can customize their experience by controlling the height and intensity of the flames, allowing for a cozy ambiance that can be tailored to any occasion. Additionally, the insert is equipped with high-grade ceramic glass that provides both durability and a clear view of the mesmerizing flames, enhancing the visual appeal of any room.

Another important characteristic of the HUDBAY-INS is its safety features. The unit comes with a built-in Oxygen Depletion Sensor (ODS), which ensures that the fireplace will shut off automatically if oxygen levels become too low, providing peace of mind for families. This feature underscores HHT’s commitment to safety in home heating solutions.

Energy efficiency is a key consideration for modern homeowners, and the HUDBAY-INS excels in this area. With its ability to provide warmth without excessive energy consumption, the insert is an eco-friendly choice that aligns with sustainable living practices. It is compatible with various home designs, lending flexibility to those looking to enhance their interiors with functional yet stylish heating solutions.

Durability is another hallmark of the HUDBAY-INS. Constructed with high-quality materials, it promises longevity and reliable performance while also providing a range of customizable finishes to suit individual tastes. Whether one prefers a sleek modern look or a more traditional aesthetic, the HUDBAY-INS can seamlessly integrate into any environment.

In conclusion, the Hearth and Home Technologies HUDBAY-INS represents a perfect synthesis of innovative technology, safety features, and aesthetic versatility. It stands out as an era-defining product that prioritizes user comfort, energy efficiency, and design flexibility, making it an ideal choice for contemporary households seeking effective home heating solutions.