Hearth and Home Technologies HUDBAY-INS Maintaining and Servicing Appliance, Glass Replacement

Page 28

11 Maintaining and Servicing Appliance

Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualified service technician should perform an appliance checkup at the beginning of each heating season.

WARNING

Risk of injury or property damage.

Before servicing:

•Turn off gas.

•Turn off electricity to appliance.

•Disable remote control, if one is present.

•Ensure appliance is completely cooled.

After servicing:

•Replace any screen or barrier that was removed.

•Reseal and reinstall any venting removed for servicing.

WARNING

Annual inspection by qualified technician recommended.

Check:

•Condition of glass, glass assembly and glass seal.

•Obstructions of combustion and ventilation air.

•Obstructions of termination cap.

•Burner ignition and operation.

•Burner air shutter adjustment

•Gas connections and fittings.

Clean:

•Glass

•Air passageways, grilles, control compartment

•Burner, burner ports

Risk of:

•Fire

•Delayed ignition or explosion

•Exposure to combustion fumes

•Odors

CAUTION

Handle glass assembly with care.

NOTE: Clean glass after initial 3-4 hours operation.

Longer operation without cleaning glass may cause a permanent white film on glass.

When cleaning glass door:

•Avoid striking, scratching or slamming glass.

•Do NOT use abrasive cleaners.

•Use a hard water deposit glass cleaner on white film.

•Do NOT clean glass when hot.

•Turn off appliance after 3-4 hours of operation and

ALLOW TO COOL.

•Remove and clean glass assembly.

•Replace glass assembly and operate appliance for additional 12 hours.

Refer to maintenance instructions.

WARNING

Inspect external vent cap regularly.

•Ensure no debris blocks cap.

•Combustible materials blocking cap may ignite.

•Restricted air flow affects burner operation.

A.Glass Replacement

Glass can be replaced either as three separate pieces, or as an assembly with the door. See Service Parts List.

To Replace Separate Glass Pieces

•Turn off gas to the appliance.

•Remove the door and set on a protective surface.

•Remove the door crown.

•Remove the top and bottom retainer screws from the front of the door. Set the top and bottom glass retainers aside.

•Loosen the side glass retainer screws, but do not remove.

•Remove the glass pieces and discard. Keep the aluminum channels for reassembly.

•Slide replacement side glass into the side glass retainers.

•Place the aluminum channels over the side glass.

•Install the center glass into the aluminum channels.

•Reinstall the glass retainers and screws. Reinstall door crown.

Door Frame with Glass Assembly Replacement

Use only Door Assembly replacement as specified in Sec- tion 8 of this manual, available from your dealer, if any glass becomes broken in the Hudson Bay Insert.

Follow the previous instructions to install the door crown and grille to the new Door Assembly.

Note: The glass and gasketing must be replaced as a complete unit as supplied by the manufacturer. Do not use substitute material.

28

Quadra-Fire • Hudson Bay Insert • 7008-115 Rev. H • 10/08

Page 27 Page 29
Image 28
Page 27 Page 29
Contents HUDBAY-INS What to do if you smell gasDo Discardnot Welcome to the Quadra-Fire Family Table of Contents Listing and Code Approvals Installation to ensure maximum safety and benefit Getting StartedTools and Supplies Needed Read all of the instructions before starting the instaFraming and Clearances Selecting Appliance LocationClearances to Combustibles HearthTermination Locations Vent Termination Minimum ClearancesVenting and Installation Vent InformationExhaust AIR Vent Pipe Termination CAP Adaptor Gas Information Fuel ConversionsConverting to LP Gas Screws Nuts Holding Burner PANValve Regulator Replacement Gas Pressures Gas Connection Check for GAS LeaksRecommendation for Wire Connecting to the ApplianceStanding Pilot Ignition System Wiring Wire Size Max. LengthPilot Appliance Setup AccessoriesDoor Crown Installation Remove Shipping MaterialsPanel Set Installation Grille InstallationBack of TOP Panel Screws Back of Side Panel Brick Installation Retaining TabsPositioning the Logs Rear Brick Retaining TabsMineral Wool Blower InstallationIncluded in kit Blower = 1/4 in mm female spade = 1/4 in mm male spade Air Shutter Adjustment Operating Instructions Before Lighting ApplianceFor Your Safety Read Before Lighting Lighting ApplianceInitial Break-in Procedure Frequently Asked QuestionsAfter Appliance is Lit Symptom Possible Causes Corrective Action TroubleshootingStanding Pilot Ignition System Troubleshooting Symptom Possible Cause Corrective ActionGlass Replacement Door Frame with Glass Assembly ReplacementMaintaining and Servicing Appliance To Replace Separate Glass PiecesMaintenance Tasks Inspect Necessary. USE Caution When CLEANING/HANDLING Ceramic BurnerAppliance Dimension Diagram Reference MaterialsVent Components List HHTLog Set Assembly Service PartsDepot Service Parts ListDescription Serial # Part Number Standing Pilot Valve Assembly StockedCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information

HUDBAY-INS specifications

Hearth and Home Technologies (HHT) has consistently set the benchmark in the hearth industry with its innovative products. One of its noteworthy offerings is the HUDBAY-INS, a vent-free gas fireplace insert designed to provide unparalleled comfort and efficiency in home heating. The HUDBAY-INS showcases a blend of modern technology, aesthetic appeal, and user-friendly features that cater to the evolving needs of homeowners.

At the heart of the HUDBAY-INS is its advanced vent-free technology. This allows the fireplace insert to operate without the need for flues or chimneys, resulting in an efficient heating solution that maximizes energy use. Homeowners can enjoy the benefits of a warm, inviting space without the complexities associated with traditional vented models. The vent-free design also simplifies installation, making it a versatile option suitable for various home layouts.

One of the standout features of the HUDBAY-INS is its adjustable flame. Users can customize their experience by controlling the height and intensity of the flames, allowing for a cozy ambiance that can be tailored to any occasion. Additionally, the insert is equipped with high-grade ceramic glass that provides both durability and a clear view of the mesmerizing flames, enhancing the visual appeal of any room.

Another important characteristic of the HUDBAY-INS is its safety features. The unit comes with a built-in Oxygen Depletion Sensor (ODS), which ensures that the fireplace will shut off automatically if oxygen levels become too low, providing peace of mind for families. This feature underscores HHT’s commitment to safety in home heating solutions.

Energy efficiency is a key consideration for modern homeowners, and the HUDBAY-INS excels in this area. With its ability to provide warmth without excessive energy consumption, the insert is an eco-friendly choice that aligns with sustainable living practices. It is compatible with various home designs, lending flexibility to those looking to enhance their interiors with functional yet stylish heating solutions.

Durability is another hallmark of the HUDBAY-INS. Constructed with high-quality materials, it promises longevity and reliable performance while also providing a range of customizable finishes to suit individual tastes. Whether one prefers a sleek modern look or a more traditional aesthetic, the HUDBAY-INS can seamlessly integrate into any environment.

In conclusion, the Hearth and Home Technologies HUDBAY-INS represents a perfect synthesis of innovative technology, safety features, and aesthetic versatility. It stands out as an era-defining product that prioritizes user comfort, energy efficiency, and design flexibility, making it an ideal choice for contemporary households seeking effective home heating solutions.
Top Page Image Contents