Hearth and Home Technologies HST-48D Accessories, Gas Log/Lighter Provision, Wood Burning Inserts

Page 41

12 Accessories

A. Gas Log/Lighter Provision

WARNING! Fire and/or Asphyxiation Risk! Use with solid wood fuel or decorative gas appliance only. Gas fire generates fumes.

•DO NOT install unvented gas logs

•Damper must be locked fully open when gas logs are installed

A certified gas log lighter or decorative gas log set can be installed in this fireplace.

•Maximum input is 100,000 BTU/hr.

•Decorative gas appliance must be certified to ANSI Z21.60 “Standard for Decorative Gas Appliances for Installation in Vented Fireplaces”.

•Must be installed in accordance with the National Fuel

Gas Code, ANSI Z223.1.

•A gas log set must incorporate a gas shutoff.

•Gas Log set requires the damper to be locked fully open.

•A listed automatic damper system with safety interlock may be used in this fireplace with only compatible, listed gas log sets. See damper system manufacturer’s insturctions.

•Knockouts are provided on both sides of the fireplace and in refractories for 1/2 in. (13 mm) iron pipe.

•Seal refractory around pipe with fireplace mortar or a non-combustible sealant.

B. Wood Burning Inserts

WARNING! Risk of Fire! Improper installation of wood in- serts may cause fireplace or chimney system to overheat.

If a wood burning insert is being installed in this fireplace, Hearth & Home Technologies recommends full reline of the chimney.

•Cooling air openings at the top of the chimney must not be obstructed in any manner.

•Hearth & Home Technologies recommends securing the reline at the top of the flue and using the cap certified for use with this fireplace system.

Firebox

Refractory

Seal with fireplace mortar or non-combust- ible sealant

Outer Shell

of Fireplace

Maintain air clearance to combustibles.

Combustible

Materials

Gas Line

Repack

Insulation

Knockout

Gas Line

4 in. (102 mm)

1 1/2 in. (38 mm) air space around

pipe

Combustible materials may be located at zero clearance to gas line beyond 4 in. (102 mm) from fireplace side.

Figure 12.1 Gas Line Installation

Heat & Glo • HST-48D US-CAN • 4012-040 • Rev F • 11/08

41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Operation Wood Burning FireplaceHot screen/mesh and glass doors will cause burns Fire RiskNumber Listing Label Information/LocationGrate User Guide Table of ContentsInstaller Guide CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited WarrantyHeat & Glo HST-48D US-CAN 4012-040 Rev F 11/08 Appliance Certification Listing and Code ApprovalsNon-Combustible Materials Combustible MaterialsHot glass will cause burns Operating InstructionsYour Fireplace Starting a Fire Seasoned WoodGrate FirescreenVented Gas Log Sets & Gas Log Lighters Glass DoorsOptional Components Clear SpaceHardwood vs Softwood Wood FuelDisposal of Ashes Maintainance and ServiceChimney Inspection/Cleaning Check Firebox Refractory Glass CleaningInspect Grate Frequency As desiredStart Fire Problems Possible Cause Solution Troubleshooting GuideTypical Fireplace System Getting StartedNegative Pressure Design and Installation ConsiderationsDraft Frequently open doors Central heat outlets or returns Locating Fireplace & ChimneyInspect Fireplace and Components Tools and Supplies NeededFireplace System Requirements 1676 mm Hearth Framing & ClearancesSelect Fireplace Location Clearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsThings to Consider Installation of FireplacePosition the Fireplace Place Protective Metal Hearth StripsYES Ft min. from top of uppermost chimney section to air inletOutside Air Install Outside Air KitHood Wire Ties Maintain minimum height of chimney above roof Chimney AssemblyC,f Chimney RequirementsExample Using Offsets/ReturnsAssemble Chimney Sections Install Chimney Air KitInstalling the Ceiling Firestop Install Ceiling Firestops330 mm Install Attic Insulation ShieldCut out Hole in Roof Complete InstallationInstall Flashing Flat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsInstall Chase Top Install Fireplace & ChimneyInstall as per Sections 7 Caulk all seams to prevent leaks Refer to FigureST1175/ST475 Square Termination Cap Install Termination CapTCT1175 Terra Cotta Cap Installing a TCT1175 Terra Cotta CapField Constructed Shrouds ShroudsRadiation Shield Mailbox Style Shroud radiation shield required = 1/k x inches of thickness FinishingHearth Extension Finishing Material High temperature sealantCombustible Mantel Fireplace opening 1194 mm Width of fireplace 305 mmGas Log/Lighter Provision AccessoriesWood Burning Inserts Gas Code, Ansi Z223.1Reference Materials Fireplace DimensionsHeat & Glo HST-48D US-CAN Rev F 11/081676 mm 508 mm 13 mm Catalog # Chimney Components457 mm Inside Diameter39-7/8 711 mm 51 mm25-1/4 14-3/4 375 mm 584 mm HST-48D Service PartsDo not Discard this Manual

HST-48D specifications

Hearth and Home Technologies (HHT) is renowned for its commitment to innovation and quality in the hearth industry, and the HST-48D model exemplifies this dedication. The HST-48D is a versatile and efficient gas fireplace designed to enhance both residential and commercial spaces. With its modern aesthetic and impressive performance, it has become a popular choice among homeowners and builders alike.

One of the standout features of the HST-48D is its sleek design. Featuring a large viewing area, the fireplace allows for maximum visibility of the dancing flames while contributing to a contemporary décor. The clean lines and elegant finish make it a perfect fit for various interior styles, from traditional to modern. Optional decorative fronts and media options offer further customization, enabling homeowners to tailor the look of their fireplace to match their personal taste.

In terms of performance, the HST-48D boasts a high efficiency rating, ensuring that it not only provides warmth but does so in an eco-friendly manner. The fireplace operates on natural gas or propane, offering flexibility in terms of fuel choice, and its efficient burner system generates a significant amount of heat while minimizing energy consumption. This makes it an excellent option for both primary and supplementary heating.

The HST-48D is equipped with advanced technology to enhance user experience. The fireplace features a state-of-the-art electronic ignition system, allowing for reliable and easy starts. Additionally, the multi-function remote control gives users the ability to adjust the flame height, control the blower, and manage other settings with ease from the comfort of their chair.

Safety is another key characteristic of the HST-48D. It adheres to strict safety standards and includes features such as a tempered glass front to prevent accidental burns, ensuring peace of mind for families and pets.

Overall, the Hearth and Home Technologies HST-48D represents a fusion of aesthetics, technology, and safety. Its modern design, high efficiency, and user-friendly features make it a standout choice for those looking to enhance their living spaces with a reliable and stylish heating solution. Whether for relaxing evenings with family or entertaining guests, the HST-48D transforms any environment into a warm and inviting haven.
Top Page Image Contents