Hearth and Home Technologies HST-48D owner manual 14-3/4 375 mm 584 mm

Page 46

						72 in.
						(1829 mm)


						13-3/8 in.
						(340 mm)
						(340 mm)
		15-3/4 in.
		(400		mm)
		(400		mm)




TR11/TR444 - Round Termination Cap						2 in.

(51 mm)

CT56 Chase Top

32-3/8 in.

(822 mm)

34-3/8 in.

(873 mm)

TR11T/TR442 - Round Telescoping Termination Cap

36in.

(914 mm)

14-3/4 in.			C
(375 mm)			C
(375 mm)
			D					B
23 in.	23 in.							B
23 in.
(584 mm)
(584 mm)	(584 mm)				A
	(584 mm)				A
ST1175/ST475 - Square Termination Cap			LDS33/LDS46 Decorative Shroud
				A		B		C		D
		Catalog #	in.	mm	in.	mm	in.	mm	in.	mm
20 in.		LDS33	36	914	36	914	8-1/2	216	11	279
20 in.		LDS46	48	1219	72	1829	8-1/2	216	11	279
(508 mm)		LDS46	48	1219	72	1829	8-1/2	216	11	279
(508 mm)
								E
17 in.								D
17 in.
(432 mm)	9-3/8 in.					C
	9-3/8 in.					C
	(238 mm)					B
								A
9-1/4 in.
(235 mm)				LDS-BV Decorative Shroud
				LDS-BV Decorative Shroud
TCT1175 - Terra Cotta Cap		Catalog #			A	B	C	D	E
TCT1175 - Terra Cotta Cap		LDS-BV		in.	26	12-1/2	15-1/2	22	23
				in.	26	12-1/2	15-1/2	22	23
				mm	660	318	394	533	584
				mm	660	318	394	533	584

46	Heat & Glo • HST-48D US-CAN • 4012-040 • Rev F • 11/08

Image 46

Contents Hot screen/mesh and glass doors will cause burns Wood Burning FireplaceOperation Fire RiskGrate Listing Label Information/LocationNumber Installer Guide Table of ContentsUser Guide Warranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHeat & Glo HST-48D US-CAN 4012-040 Rev F 11/08 Non-Combustible Materials Listing and Code ApprovalsAppliance Certiﬁcation Combustible MaterialsYour Fireplace Operating InstructionsHot glass will cause burns Grate Seasoned WoodStarting a Fire FirescreenOptional Components Glass DoorsVented Gas Log Sets & Gas Log Lighters Clear SpaceWood Fuel Hardwood vs SoftwoodChimney Inspection/Cleaning Maintainance and ServiceDisposal of Ashes Inspect Grate Glass CleaningCheck Firebox Refractory Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemDraft Design and Installation ConsiderationsNegative Pressure Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsFireplace System Requirements Tools and Supplies NeededInspect Fireplace and Components Select Fireplace Location Framing & Clearances1676 mm Hearth Clearances Clearances to Combustible MaterialsSidewalls/Surrounds Frame the FireplacePosition the Fireplace Installation of FireplaceThings to Consider Place Protective Metal Hearth StripsFt min. from top of uppermost chimney section to air inlet YESHood Wire Ties Install Outside Air KitOutside Air Chimney Assembly Maintain minimum height of chimney above roofChimney Requirements C,fUsing Offsets/Returns ExampleInstall Chimney Air Kit Assemble Chimney SectionsInstall Ceiling Firestops Installing the Ceiling FirestopInstall Attic Insulation Shield 330 mmInstall Flashing Complete InstallationCut out Hole in Roof Chimney Termination Requirements Flat RoofsChase Installations Construct the ChaseInstall as per Sections 7 Install Fireplace & ChimneyInstall Chase Top Caulk all seams to prevent leaks Refer to FigureInstall Termination Cap ST1175/ST475 Square Termination CapInstalling a TCT1175 Terra Cotta Cap TCT1175 Terra Cotta CapRadiation Shield ShroudsField Constructed Shrouds Mailbox Style Shroud radiation shield required Hearth Extension Finishing= 1/k x inches of thickness High temperature sealant Finishing MaterialFireplace opening 1194 mm Width of fireplace 305 mm Combustible MantelWood Burning Inserts AccessoriesGas Log/Lighter Provision Gas Code, Ansi Z223.1Heat & Glo HST-48D US-CAN Fireplace DimensionsReference Materials Rev F 11/08 1676 mm 508 mm 13 mm 457 mm Chimney ComponentsCatalog # Inside Diameter25-1/4 51 mm39-7/8 711 mm 14-3/4 375 mm 584 mm Service Parts HST-48DDo not Discard this Manual