Hearth and Home Technologies RHW-485H owner manual Complete the Enclosure, Chimney Termination

Page 21

6 Complete the Enclosure

A. Chimney Termination

Chimney Termination Requirements (See Figures 6.1 and 6.2)

•Must have a cap approved and listed for this fireplace system

•Must not be located where it will become plugged by snow or other material

•Must terminate at least 3 ft (914 mm) above the roof and at least 2 ft (610 mm) above any portion of the roof within 10 ft (3.05 m)

•Must be located away from trees or other structures

Slanted Roofs

Chimney must

 

 

Chimney must extend 2 ft (.6 m)

 

 

 

above any portion of the roof

 

extend 3 ft (.9 m)

 

 

 

 

 

within 10 ft (3 m) of the chimney

 

above the roof

 

 

 

 

 

 

 

 

 

 

 

 

 

Flat Roofs

Chimney must extend 2 ft (.6 m) above any portion of the roof within 10 ft (3 m) of the chimney

Chimney must extend 3 ft (.9 m) above the roof

Figure 6.1 Termination Requirements

 

Gas, Wood or Fuel

 

 

Oil Termination

 

 

 

 

20 in.

 

 

 

(508 mm)

 

18 in.

 

(minimum) to

 

 

Perpendicular

 

(457 mm)

 

Wall

 

 

A

(gas only)

 

 

 

Gas

 

 

 

Termination

 

 

Gas Termination

Wood & Fuel Oil Terminatio

A

6 in. (152 mm)

 

20 in. (508 mm)

Figure 6.2

Multiple Chimneys

 

Mark the Exit Point of the Roof

Locate the point where the chimney will exit the roof by plumbing down to the center of the chimney. Drive a nail up through the roof to mark the center. See Figure 6.3.

Cut Out the Hole in the Roof

Measure to either side of the nail and mark the 14-1/2 in. x 14-1/2 in. (368 mm x 368 mm) opening required. This is measured on the horizontal; actual length may be larger depending on the pitch of the roof. Cut out and frame the opening. See Chapter 25 of the Uniform Building Code for roof framing details.

WARNING

Fire Risk

•Must maintain 2 in. (51 mm) air clearance to insulation and other combustible materials.

Assemble the Chimney Sections Through the Roof

Continue to add chimney sections through the roof opening, maintaining at least a 2 in. (51 mm) air space to combustible materials.

Install the Roof Flashing

 

If a roof flashing is to be used, install the roof flashing appropriate to the

 

roof pitch and install a round termination cap and storm collar following the

 

instructions shipped with the cap.

Figure 6.3 Ceiling/Attic Construction

Heat & Glo • RHW-485 • 33221 Rev O • 08/06

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Fire Risk Models RHW-485, RHW-485H Woodburning FireplaceListing Label Information/Location GrateNumber Table of Contents Listing and Code Approvals Appliance CertificationNot intended for use as a primary heat source Getting Started Design and Installation ConsiderationsNegative Pressure Asphyxiation RiskMarginal Location Typical Fireplace System Typical Fireplace SystemTools and Supplies Needed Inspect Fireplace and ComponentsFire Risk Explosion Risk Selecting Fireplace Location Framing and ClearancesClearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsChimney Requirements Construct the ChaseInstall the Outside Air Kit Installation of FireplaceSharp Edges Asphyxiation Risk Risk of Smoke SpillageFt min. from top of uppermost chimney section to air inlet Position the Fireplace Secure the FireplacePlace the Protective Metal Hearth Strips Level the FireplaceChimney Assembly Height of Chimney Components Degree SL306 SL312 SL318 SL324 SL336 SL348 Using Offsets/ReturnsAssemble the Chimney Sections Install the Ceiling FirestopsInstall the Attic Insulation Shield Double-check the Chimney AssemblySecure the Chimney Chimney Termination Complete the EnclosureInstall the Termination Cap Install the Chimney Air Kit required in CanadaChase Top Installing an ST375 Square Termination Cap Accessories Gas Log/Lighter ProvisionsGas Code, Ansi Z223.1 Hearth Extension FinishingMantel Finishing MaterialGlass Doors Combustible MaterialGeneral Information Operating InstructionsClear Space Near the Fireplace Outside AirFlue Damper FirescreenWood Fuel GrateFirewood MoistureStarting a Fire Understanding Vent Problems TroubleshootingDiagnostic Questions Diagnostics and Problem SolvingSolutions Can’t get a good fire going. What am I doing wrong?fireplace burns the wood too fast. What can I do? Chimney Inspection/Cleaning Maintenance and Servicing the FireplaceDisposal of Ashes Firebox RefractoryWhen cleaning glass door Maintenance Task ListClean Chimney FireReference Materials Fireplace DimensionsCatalog # Description Fireplace ComponentsCatalog # Chimney Components14-1/2 1829 mm 10-7/8 276 mm 406 mm 508 mm Minimum Base Dimensions 26.5 X 28 with 34 X 34 with Minimum Base Dimensions 28 X 28 with 32 X 32 with 23 XTR442 TR442 / 444 TV 20 xThis page intentionally left blank RHW-485 Service PartsHerringbone Brick Refractory option available week 03/04 Description of Part RHW-485 RHW-485H QtyThis page intentionally left blank Limited Warranty Warranty For Heat & GLO FireplacesDo Discardnot Contact Information

RHW-485, RHW-485H specifications

Hearth and Home Technologies (HHT) is a leader in the manufacture of innovative and high-quality hearth products, and their RHW-485H and RHW-485 models are no exceptions. These wood-burning heaters are designed to provide efficient and effective heating solutions for residential spaces while offering an elegant aesthetic that complements various home decors.

One of the main features of the RHW-485H and RHW-485 is their impressive heating capacity. Both models are designed to heat areas up to 2,000 square feet efficiently, making them ideal for large living spaces or open-concept homes. This significant heating capability is made possible by advanced combustion technology that allows for a longer burn time, ensuring extended warmth throughout the night.

Another defining characteristic of these units is their clean-burning technology. HHT has incorporated a unique air wash system that enhances combustion efficiency and minimizes emissions. This ensures that homeowners can enjoy the beauty and comfort of a wood fire while adhering to environmental standards. Furthermore, these models have received certification from the EPA for meeting stringent guidelines, making them an excellent choice for those who are environmentally conscious.

In terms of design, the RHW-485H features an attractive cast iron door with a large viewing window. This allows for an unobstructed view of the mesmerizing flames and adds a touch of sophistication to any room. The RHW-485, while similar in heating efficiency, offers slightly different aesthetic options, giving homeowners the ability to choose a model that aligns with their personal style.

Both models come equipped with a robust refractory system that enhances heat retention and distribution. This technology ensures that heat is released evenly and efficiently, providing consistent warmth without the need for constant refueling. Additionally, they feature adjustable air controls that allow users to manage burn rates and heat output according to their preferences.

Another important aspect is the ease of installation and maintenance. The RHW-485H and RHW-485 have been designed with user-friendly features, including accessible clean-out ports that simplify ash removal. This reduces the hassle of routine care, allowing homeowners to enjoy their fireplace without extensive upkeep.

In conclusion, Hearth and Home Technologies’ RHW-485H and RHW-485 models are premium wood-burning heaters that combine efficiency, elegance, and environmental responsibility. They offer a perfect blend of modern technology and classic design, making them an excellent choice for discerning homeowners looking to enhance their living space with warmth and style.
Top Page Image Contents