Hearth and Home Technologies RHW-485H owner manual Starting a Fire

Page 30

I. Starting a Fire

Check the flue damper to be certain it is in the full open po- sition. Place crumpled or twisted paper under the fireplace grate. Loosely arrange kindling or small pieces of wood to form a layer above the paper.

The fires must be built on the fireplace grate, without danger of the burning fuel falling out of the fireplace opening.

Light the paper and add small pieces of wood until a hot bed of embers has been established.

After establishing the fire bed, and the small firewood is burn- ing briskly, add a minimum of three average sized pieces of split firewood, place the wood in such a manner to allow combustion air and flames between them.

Note: When first lighting your fireplace, it may be neces- sary to pre-warm the flue to establish a draft. This is done by holding a rolled up piece of burning newspaper under the flue damper for a few moments. This will help reduce smoke spillage during start-up.

Note: The first three or four fires should be of moderate size to allow the oils and binders to be burned from the fireplace and the refractory and paint to cure. You may notice an industrial odor the first few fires. This is consid- ered normal.

CAUTION

Odors and vapors released during initial operation.

•Curing of high temperature paint.

•Open windows for air circulation.

Odors may be irritating to sensitive individuals.

WARNING

Fire Risk

Keep combustible materials, gasoline and other flammable vapors and liquids clear of fireplace.

•Do NOT store flammable materials close to the fireplace.

•Do NOT use gasoline, lantern fuel, kerosene, charcoal lighter fluid or similar liquids to start or “freshen up” a fire in this fireplace.

•Keep all such liquids well away from the fireplace while it is in use.

Combustible materials may ignite.

30

Heat & Glo • RHW-485 • 33221 Rev O • 08/06

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Models RHW-485, RHW-485H Woodburning Fireplace Fire RiskListing Label Information/Location GrateNumber Table of Contents Listing and Code Approvals Appliance CertificationNot intended for use as a primary heat source Negative Pressure Design and Installation ConsiderationsGetting Started Asphyxiation RiskMarginal Location Typical Fireplace System Typical Fireplace SystemTools and Supplies Needed Inspect Fireplace and ComponentsFire Risk Explosion Risk Framing and Clearances Selecting Fireplace LocationClearances Clearances to Combustible MaterialsSidewalls/Surrounds Frame the FireplaceConstruct the Chase Chimney RequirementsSharp Edges Asphyxiation Risk Installation of FireplaceInstall the Outside Air Kit Risk of Smoke SpillageFt min. from top of uppermost chimney section to air inlet Place the Protective Metal Hearth Strips Secure the FireplacePosition the Fireplace Level the FireplaceChimney Assembly Height of Chimney Components Using Offsets/Returns Degree SL306 SL312 SL318 SL324 SL336 SL348Install the Ceiling Firestops Assemble the Chimney SectionsInstall the Attic Insulation Shield Double-check the Chimney AssemblySecure the Chimney Complete the Enclosure Chimney TerminationInstall the Termination Cap Install the Chimney Air Kit required in CanadaChase Top Installing an ST375 Square Termination Cap Accessories Gas Log/Lighter ProvisionsGas Code, Ansi Z223.1 Finishing Hearth ExtensionGlass Doors Finishing MaterialMantel Combustible MaterialOperating Instructions General InformationFlue Damper Outside AirClear Space Near the Fireplace FirescreenFirewood GrateWood Fuel MoistureStarting a Fire Troubleshooting Understanding Vent ProblemsSolutions Diagnostics and Problem SolvingDiagnostic Questions Can’t get a good fire going. What am I doing wrong?fireplace burns the wood too fast. What can I do? Disposal of Ashes Maintenance and Servicing the FireplaceChimney Inspection/Cleaning Firebox RefractoryClean Maintenance Task ListWhen cleaning glass door Chimney FireFireplace Dimensions Reference MaterialsFireplace Components Catalog # DescriptionChimney Components Catalog #14-1/2 1829 mm 10-7/8 276 mm 406 mm 508 mm TR442 TR442 / 444 TV Minimum Base Dimensions 28 X 28 with 32 X 32 with 23 XMinimum Base Dimensions 26.5 X 28 with 34 X 34 with 20 xThis page intentionally left blank Service Parts RHW-485Description of Part RHW-485 RHW-485H Qty Herringbone Brick Refractory option available week 03/04This page intentionally left blank Warranty For Heat & GLO Fireplaces Limited WarrantyContact Information Do Discardnot

RHW-485, RHW-485H specifications

Hearth and Home Technologies (HHT) is a leader in the manufacture of innovative and high-quality hearth products, and their RHW-485H and RHW-485 models are no exceptions. These wood-burning heaters are designed to provide efficient and effective heating solutions for residential spaces while offering an elegant aesthetic that complements various home decors.

One of the main features of the RHW-485H and RHW-485 is their impressive heating capacity. Both models are designed to heat areas up to 2,000 square feet efficiently, making them ideal for large living spaces or open-concept homes. This significant heating capability is made possible by advanced combustion technology that allows for a longer burn time, ensuring extended warmth throughout the night.

Another defining characteristic of these units is their clean-burning technology. HHT has incorporated a unique air wash system that enhances combustion efficiency and minimizes emissions. This ensures that homeowners can enjoy the beauty and comfort of a wood fire while adhering to environmental standards. Furthermore, these models have received certification from the EPA for meeting stringent guidelines, making them an excellent choice for those who are environmentally conscious.

In terms of design, the RHW-485H features an attractive cast iron door with a large viewing window. This allows for an unobstructed view of the mesmerizing flames and adds a touch of sophistication to any room. The RHW-485, while similar in heating efficiency, offers slightly different aesthetic options, giving homeowners the ability to choose a model that aligns with their personal style.

Both models come equipped with a robust refractory system that enhances heat retention and distribution. This technology ensures that heat is released evenly and efficiently, providing consistent warmth without the need for constant refueling. Additionally, they feature adjustable air controls that allow users to manage burn rates and heat output according to their preferences.

Another important aspect is the ease of installation and maintenance. The RHW-485H and RHW-485 have been designed with user-friendly features, including accessible clean-out ports that simplify ash removal. This reduces the hassle of routine care, allowing homeowners to enjoy their fireplace without extensive upkeep.

In conclusion, Hearth and Home Technologies’ RHW-485H and RHW-485 models are premium wood-burning heaters that combine efficiency, elegance, and environmental responsibility. They offer a perfect blend of modern technology and classic design, making them an excellent choice for discerning homeowners looking to enhance their living space with warmth and style.
Top Page Image Contents