Hearth and Home Technologies RHW-485H Maintenance and Servicing the Fireplace, Disposal of Ashes

Page 34

11 Maintenance and Servicing the Fireplace

A. Disposal of Ashes

Ashes should be placed in a metal container with a tight-fit- ting lid. The closed container of ashes should be placed on a noncombustible floor or on the ground, well away from all combustible materials, pending final disposal. If the ashes are disposed of by burial in soil or otherwise locally dis- persed, they should be retained in the closed container until all embers have thoroughly cooled.

WARNING

Fire Risk

Disposal of ashes

•Ashes should be placed in metal container with tight fitting lid.

•Do not place metal container on combustible surface.

•Ashes should be retained in closed container until all embers have thoroughly cooled.

WARNING

Fire Risk

Prevent creosote buildup

•Inspect chimney once every two months during heating season.

•Remove creosote to reduce risk of chimney fire.

•Ignited creosote is extremely HOT.

B. Chimney Inspection/Cleaning

Inspect the chimney internally for obstructions and construc- tion damage. Flue pipe joints and seams must be continu- ous and mechanically tight.

The chimney should be inspected once every two months during the heating season.

If creosote has accumulated, it should be removed to reduce the risk of a chimney fire.

Refer to Figure 11.1 to remove/reinstall termination caps.

C. Firebox Refractory

Check firebox refractory for excessive cracks or gaps. If cracks exceed 1/4 in. (6 mm) in width the refractory should be replaced. See Section 12 for replacement information.

WARNING

Fire Risk

•Inspect fireplace refractory annually.

Crumbling, deteriorated refractory can allow overheating of surrounding materials.

Note: As you use the fireplace, expansion and contraction will cause minor cracking of the refractory. This is normal, unavoidable, and will not affect the performance of the fireplace. If the cracks become large enough that the metal behind the refractory is exposed or large pieces fall out, the panels should be replaced.

Remove 8 screws (9 for King), lift top cover.

Cap Top

(Be sure holes in cap top and cap base are aligned.)

Cap Base

Remove screws,

Remove 4 screws

lift top cover.

and lift top pan off.

Top Cover

 

 

 

Cap

Cap

 

 

Chimney

Slip

Section

1.Remove the 4 screws.

2.Remove the screen.

3.Remove the baffle.

Cap

Chase

Remove 2 screws from the front and back and lift the top off.

European Copper Series

TR344/TR342

ST375

TS345/TS345P

TCT375

Termination Cap

Round

Square

Square

Terra Cotta

(CT3-King shown)

Termination Cap

Termination Cap

Termination Caps

Termination Cap

Figure 11.1 Chimney & Termination Cap Cleaning

34

Heat & Glo • RHW-485 • 33221 Rev O • 08/06

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Models RHW-485, RHW-485H Woodburning Fireplace Fire RiskGrate Listing Label Information/LocationNumber Table of Contents Appliance Certification Listing and Code ApprovalsNot intended for use as a primary heat source Negative Pressure Design and Installation ConsiderationsGetting Started Asphyxiation RiskMarginal Location Typical Fireplace System Typical Fireplace SystemInspect Fireplace and Components Tools and Supplies NeededFire Risk Explosion Risk Framing and Clearances Selecting Fireplace LocationClearances Clearances to Combustible MaterialsSidewalls/Surrounds Frame the FireplaceConstruct the Chase Chimney RequirementsSharp Edges Asphyxiation Risk Installation of FireplaceInstall the Outside Air Kit Risk of Smoke SpillageFt min. from top of uppermost chimney section to air inlet Place the Protective Metal Hearth Strips Secure the FireplacePosition the Fireplace Level the FireplaceChimney Assembly Height of Chimney Components Using Offsets/Returns Degree SL306 SL312 SL318 SL324 SL336 SL348Install the Ceiling Firestops Assemble the Chimney SectionsDouble-check the Chimney Assembly Install the Attic Insulation ShieldSecure the Chimney Complete the Enclosure Chimney TerminationInstall the Chimney Air Kit required in Canada Install the Termination CapChase Top Installing an ST375 Square Termination Cap Gas Log/Lighter Provisions AccessoriesGas Code, Ansi Z223.1 Finishing Hearth ExtensionGlass Doors Finishing MaterialMantel Combustible MaterialOperating Instructions General InformationFlue Damper Outside AirClear Space Near the Fireplace FirescreenFirewood GrateWood Fuel MoistureStarting a Fire Troubleshooting Understanding Vent ProblemsSolutions Diagnostics and Problem SolvingDiagnostic Questions Can’t get a good fire going. What am I doing wrong?fireplace burns the wood too fast. What can I do? Disposal of Ashes Maintenance and Servicing the FireplaceChimney Inspection/Cleaning Firebox RefractoryClean Maintenance Task ListWhen cleaning glass door Chimney FireFireplace Dimensions Reference MaterialsFireplace Components Catalog # DescriptionChimney Components Catalog #14-1/2 1829 mm 10-7/8 276 mm 406 mm 508 mm TR442 TR442 / 444 TV Minimum Base Dimensions 28 X 28 with 32 X 32 with 23 XMinimum Base Dimensions 26.5 X 28 with 34 X 34 with 20 xThis page intentionally left blank Service Parts RHW-485Description of Part RHW-485 RHW-485H Qty Herringbone Brick Refractory option available week 03/04This page intentionally left blank Warranty For Heat & GLO Fireplaces Limited WarrantyContact Information Do Discardnot

RHW-485, RHW-485H specifications

Hearth and Home Technologies (HHT) is a leader in the manufacture of innovative and high-quality hearth products, and their RHW-485H and RHW-485 models are no exceptions. These wood-burning heaters are designed to provide efficient and effective heating solutions for residential spaces while offering an elegant aesthetic that complements various home decors.

One of the main features of the RHW-485H and RHW-485 is their impressive heating capacity. Both models are designed to heat areas up to 2,000 square feet efficiently, making them ideal for large living spaces or open-concept homes. This significant heating capability is made possible by advanced combustion technology that allows for a longer burn time, ensuring extended warmth throughout the night.

Another defining characteristic of these units is their clean-burning technology. HHT has incorporated a unique air wash system that enhances combustion efficiency and minimizes emissions. This ensures that homeowners can enjoy the beauty and comfort of a wood fire while adhering to environmental standards. Furthermore, these models have received certification from the EPA for meeting stringent guidelines, making them an excellent choice for those who are environmentally conscious.

In terms of design, the RHW-485H features an attractive cast iron door with a large viewing window. This allows for an unobstructed view of the mesmerizing flames and adds a touch of sophistication to any room. The RHW-485, while similar in heating efficiency, offers slightly different aesthetic options, giving homeowners the ability to choose a model that aligns with their personal style.

Both models come equipped with a robust refractory system that enhances heat retention and distribution. This technology ensures that heat is released evenly and efficiently, providing consistent warmth without the need for constant refueling. Additionally, they feature adjustable air controls that allow users to manage burn rates and heat output according to their preferences.

Another important aspect is the ease of installation and maintenance. The RHW-485H and RHW-485 have been designed with user-friendly features, including accessible clean-out ports that simplify ash removal. This reduces the hassle of routine care, allowing homeowners to enjoy their fireplace without extensive upkeep.

In conclusion, Hearth and Home Technologies’ RHW-485H and RHW-485 models are premium wood-burning heaters that combine efficiency, elegance, and environmental responsibility. They offer a perfect blend of modern technology and classic design, making them an excellent choice for discerning homeowners looking to enhance their living space with warmth and style.
Top Page Image Contents