Hearth and Home Technologies RHW-485H fireplace burns the wood too fast. What can I do?

Page 33

The fireplace burns the wood too fast. What can I do?

Diagnostic Questions

 

Possible Causes of Condition

Solutions

Do you have glass doors?

•

Need to slow air intake

Add glass doors.

 

 

 

 

What is the condition of the

•

Extremely dry wood

Mix in less seasoned wood after fire established.

wood?

 

 

 

 

 

 

 

I smell smoke in the house during operation. What’s causing that?

Diagnostic Questions

 

Possible Causes of Condition

Solutions

Does the fire start and burn

No:

 

well?

• Damper not fully open

Open damper; check and clean chimney if needed; use adequate

 

 

•

Chimney obstruction

kindling and fuel; open glass doors or open window, check for

 

need for balanced air make-up.

 

•

Not enough kindling and/or fuel to establish

 

 

 

 

draft

 

 

•

Inadequate combustion air

 

 

Yes:

 

 

•

Fire too close to front

Build fire farther back. Do not use exhaust fans during startup

 

•

Competition with exhaust devices

and/or check for need for balanced air make-up system.

 

 

 

 

 

 

I smell smoke in the house after we’ve had a fire in the fireplace. What is the cause/what can we do?

Diagnostic Questions

 

Possible Causes of Condition

Solutions

Is the damper closed?

• No: Down draft or negative pressure

Close the damper at end of burn.

 

•

Yes: Negative pressure from exhaust fans

Check for need for glass doors. Check for need for balanced air

 

 

and/or house stack effect.

make-up system or raising chimney.

 

 

 

Is the chimney clean?

• No: Creosote odor

Have chimney cleaned.

 

•

Yes: Damper closed too early

Wait until fire completely out before closing damper.

 

 

 

 

Heat & Glo • RHW-485 • 33221 Rev O • 08/06

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Fire Risk Models RHW-485, RHW-485H Woodburning FireplaceListing Label Information/Location GrateNumber Table of Contents Listing and Code Approvals Appliance CertificationNot intended for use as a primary heat source Getting Started Design and Installation ConsiderationsNegative Pressure Asphyxiation RiskMarginal Location Typical Fireplace System Typical Fireplace SystemTools and Supplies Needed Inspect Fireplace and ComponentsFire Risk Explosion Risk Selecting Fireplace Location Framing and ClearancesClearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsChimney Requirements Construct the ChaseInstall the Outside Air Kit Installation of FireplaceSharp Edges Asphyxiation Risk Risk of Smoke SpillageFt min. from top of uppermost chimney section to air inlet Position the Fireplace Secure the FireplacePlace the Protective Metal Hearth Strips Level the FireplaceChimney Assembly Height of Chimney Components Degree SL306 SL312 SL318 SL324 SL336 SL348 Using Offsets/ReturnsAssemble the Chimney Sections Install the Ceiling FirestopsInstall the Attic Insulation Shield Double-check the Chimney AssemblySecure the Chimney Chimney Termination Complete the EnclosureInstall the Termination Cap Install the Chimney Air Kit required in CanadaChase Top Installing an ST375 Square Termination Cap Accessories Gas Log/Lighter ProvisionsGas Code, Ansi Z223.1 Hearth Extension FinishingMantel Finishing MaterialGlass Doors Combustible MaterialGeneral Information Operating InstructionsClear Space Near the Fireplace Outside AirFlue Damper FirescreenWood Fuel GrateFirewood MoistureStarting a Fire Understanding Vent Problems TroubleshootingDiagnostic Questions Diagnostics and Problem SolvingSolutions Can’t get a good fire going. What am I doing wrong?fireplace burns the wood too fast. What can I do? Chimney Inspection/Cleaning Maintenance and Servicing the FireplaceDisposal of Ashes Firebox RefractoryWhen cleaning glass door Maintenance Task ListClean Chimney FireReference Materials Fireplace DimensionsCatalog # Description Fireplace ComponentsCatalog # Chimney Components14-1/2 1829 mm 10-7/8 276 mm 406 mm 508 mm Minimum Base Dimensions 26.5 X 28 with 34 X 34 with Minimum Base Dimensions 28 X 28 with 32 X 32 with 23 XTR442 TR442 / 444 TV 20 xThis page intentionally left blank RHW-485 Service PartsHerringbone Brick Refractory option available week 03/04 Description of Part RHW-485 RHW-485H QtyThis page intentionally left blank Limited Warranty Warranty For Heat & GLO FireplacesDo Discardnot Contact Information

RHW-485, RHW-485H specifications

Hearth and Home Technologies (HHT) is a leader in the manufacture of innovative and high-quality hearth products, and their RHW-485H and RHW-485 models are no exceptions. These wood-burning heaters are designed to provide efficient and effective heating solutions for residential spaces while offering an elegant aesthetic that complements various home decors.

One of the main features of the RHW-485H and RHW-485 is their impressive heating capacity. Both models are designed to heat areas up to 2,000 square feet efficiently, making them ideal for large living spaces or open-concept homes. This significant heating capability is made possible by advanced combustion technology that allows for a longer burn time, ensuring extended warmth throughout the night.

Another defining characteristic of these units is their clean-burning technology. HHT has incorporated a unique air wash system that enhances combustion efficiency and minimizes emissions. This ensures that homeowners can enjoy the beauty and comfort of a wood fire while adhering to environmental standards. Furthermore, these models have received certification from the EPA for meeting stringent guidelines, making them an excellent choice for those who are environmentally conscious.

In terms of design, the RHW-485H features an attractive cast iron door with a large viewing window. This allows for an unobstructed view of the mesmerizing flames and adds a touch of sophistication to any room. The RHW-485, while similar in heating efficiency, offers slightly different aesthetic options, giving homeowners the ability to choose a model that aligns with their personal style.

Both models come equipped with a robust refractory system that enhances heat retention and distribution. This technology ensures that heat is released evenly and efficiently, providing consistent warmth without the need for constant refueling. Additionally, they feature adjustable air controls that allow users to manage burn rates and heat output according to their preferences.

Another important aspect is the ease of installation and maintenance. The RHW-485H and RHW-485 have been designed with user-friendly features, including accessible clean-out ports that simplify ash removal. This reduces the hassle of routine care, allowing homeowners to enjoy their fireplace without extensive upkeep.

In conclusion, Hearth and Home Technologies’ RHW-485H and RHW-485 models are premium wood-burning heaters that combine efficiency, elegance, and environmental responsibility. They offer a perfect blend of modern technology and classic design, making them an excellent choice for discerning homeowners looking to enhance their living space with warmth and style.
Top Page Image Contents