Baxi Potterton Condensing Combination Boiler Plume Outlet Elbow, General Fitting Notes, Supplied

Page 28

Plume Outlet

Fig. 34

Fig. 35

Elbow

 

9.0

 

Plume Displacement

 

 

 

 

 

 

 

 

 

 

9.3

 

General Fitting Notes (cont.)

15. For aesthetic purposes it is permissible to route the

60Ø exhaust in an enclosed box, but the air inlet and

plume outlet MUST remain in free air.

16. It is also possible to separate the plume outlet from the

93° elbow to allow the flue to be installed as shown in

Fig. 34.

 

 

17. To do this, first slacken the two screws retaining the

plume outlet to the elbow, and remove the outlet (Fig. 35).

The elbow can now be used to connect the vertical to

horizontal 60Ø exhaust (Fig. 34). Retighten the screws in

the elbow.

18. The outlet can now be fitted into the female end of an

60Ø extension piece. It must be secured using two of the

screws supplied in the bag with the ‘Jubilee’ clip.

19. Mark the female end of the extension at 30mm as

shown in two positions, directly opposite each other

(Fig. 36).

 

 

30mm

Fig. 36

200mm Min.

Fig. 37

20.

Using a suitable bit (e.g. 2mm), drill through the

extension and outlet. Secure using two of the screws

supplied.

21.

The remaining screw must be used to secure the

adaptor to the concentric terminal.

22.

When the plume outlet is positioned under a balcony

or other projection (Fig. 37) it must protrude at least

200mm (it is not necessary to extend it further than this).

23.

When under balconies or projections it is permissible to

rotate the concentric flue length up to 70°, clockwise or

anti-clockwise (Fig. 38), if there is insufficient space to

connect vertically.

24.This will allow the connection of the exhaust to the outlet spigot.

25.All other minimum & maximum dimensions must be adhered to, and the air inlet positioned such that it will not be subject to rain entry.

70°

 

 

Concentric Flue Length

 

Outlet Spigot

(shown end-on)

 

 

28

© Baxi Heating UK Ltd 2012

Fig. 38

 

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Installation & Service Instructions 0086 Installer Notification Guidelines Scheme Members onlyLegislation Important Installation, Commissioning, Service & RepairCodes of Practice refer to the most recent version Safe Manual Handling GeneralPreparation TechniqueContents Contents of Pack IntroductionDescription Optional ExtrasGeneral Layout LayoutCentral Heating Mode Fig Domestic Hot Water Mode FigFrost Protection Mode Appliance OperationTechnical Data Heatmax Combi 24, 28Dimensions and Fixings System Details InformationCentral Heating Circuit BypassSystem Filling and Pressurising Safety Pressure Relief Valve FigExpansion Vessel Central Heating only Showers Domestic Hot Water Circuit FigHard Water Areas Location Site RequirementsClearances Figs Site Requirement Ventilation of CompartmentsGas Supply Electrical SupplyCondensate Drain 50mm per 500mm minRun Minimum fallPlume Displacement Kit FlueBelow windows or openings on pitched roofs 2000 Likely flue positions requiring a flue terminal guardFlue Options Horizontal FluesHorizontal Flue Systems This bend is equivalent to 1 metreVertical Flues Vertical Flue SystemsRoof Terminal This bend is equivalent to 1 metre Metre for each 91.5 bend Metre for each 135 bendFlue Accessories Key Accessory Size Code NoFlue Dimensions For Roof TerminalsFlue Trim Terminal Guard FigPlume Displacement Plume Displacement Kit Fig28/33 Determining Permissible LengthsExample 5121368General Fitting Notes 30mmElbow to allow the flue to be installed as shown 60Ø extension piece. It must be secured using twoUsing a suitable bit e.g mm, drill through Extension and outlet. Secure using two of the screwsInstallation Unpacking & Initial PreparationFlushing After considering the site requirementsFitting The Boiler Condensate Drain see sectionFitting The Flue Wall Thickness Flue ElbowEnsure Elbow is fully engaged into Boiler Adaptor WasteY Flue25mm Extension Cut End Inner Flue Support BracketEnsure Extension is fully engaged into Boiler Adaptor Preliminary Electrical Checks Making The Electrical ConnectionsTerminal Block Cover Cable Clamp Commissioning Commissioning the BoilerCheck the Operational Working Gas Inlet Pressure Selector Switch DisplayGas Valve Completion CompletionCase Front Panel Facia Panel Annual Servicing ServicingAnnual Servicing Inspection Electrode Leads Venturi Injector Fan, Collector and Cover Assembly Threaded BushRestricter Filter Hall Effect Sensor Igniter Fig Changing ComponentsSpark and Sensing Electrodes Fig Fan Fig Venturi FigInjector Fig Gasket Venturi Injector Cover Gas Inlet Pipe Fan CollectorBurner Fig Insulation FigCentral Heating Temperature Sensor NTC Fig Safety Thermostat FigDHW Temperature Sensor NTC Fig Flue/Heat Exchanger Thermostat Sensor FigPump Complete Fig Pump Head Only FigAutomatic Air Vent Fig Pressure Gauge Figs Hall Effect Sensor FigDiverter Valve Motor Unit & Assembly Fig Plate Heat Exchanger FigSelector Switch Fig 14.22 P.C.B. FigGas Valve Fig Expansion Vessel FigSetting the Gas Valve Setting the Gas Valve CO2 checkIllustrated Wiring Diagram ElectricalShort Parts List Short Parts List306 302Initial Fault Finding Checks Fault FindingError Codes Error 133 flashing Go to section ‘A’ Turn the selector switch toReset position for 5 seconds Pump runsError 133 flashing Go to section ‘I’ Turn Domestic Hot WaterOpen DHW tap fully Close DHW tapPCB X3 connector terminals 3 Switch terminalFan jammed or faulty winding Replace PCB Replace waterReplace sensor or PCB E28 Gas at burnerReplace gas valve Terminals 1Replace PCB Is there 230V at Replace safety thermostatReplace sensor Page GAS Boiler System Commissioning Checklist Service Record Brooks House, Coventry Road, Warwick. CV34 4LL

Condensing Combination Boiler specifications

The Baxi Potterton Condensing Combination Boiler is a sophisticated heating solution designed to meet the demands of modern households while promoting energy efficiency. This state-of-the-art boiler combines both heating and hot water capabilities into a compact unit, making it an ideal choice for homes with limited space.

One of the standout features of the Baxi Potterton Condensing Combination Boiler is its impressive energy efficiency. With a high energy efficiency rating, these boilers can significantly reduce energy bills and minimize carbon footprints. The condensing technology maximizes heat recovery, allowing the boiler to utilize heat that would otherwise be lost in traditional systems. By extracting more energy from the combustion process, homeowners can enjoy reliable heating and hot water without the typical energy waste associated with older boilers.

The Baxi Potterton range is engineered for easy installation and maintenance, featuring a lightweight design that simplifies the fitting process. The built-in digital control system allows homeowners to easily adjust settings for optimal comfort and energy usage. Additionally, the boiler includes a frost protection feature, making it a reliable option for homes in colder climates.

Another key characteristic of the Baxi Potterton Condensing Combination Boiler is its powerful hot water delivery system. The combination boiler provides instant hot water on demand, eliminating the need for a separate water tank. This ensures that households have a constant supply of hot water for showers, cooking, and other domestic needs, without long wait times.

Safety is a top priority with the Baxi Potterton. The boiler is equipped with multiple safety features, including pressure relief valves and safety cut-off systems, ensuring peace of mind for homeowners. The compact design further includes a quiet operation feature, which is particularly beneficial for households where noise levels need to be kept to a minimum.

In summary, the Baxi Potterton Condensing Combination Boiler is a highly efficient, compact, and user-friendly solution for home heating and hot water needs. With its advanced technology and strong emphasis on safety, it stands out as a reliable choice for modern households looking to improve energy efficiency while maintaining comfort. Whether you are replacing an old boiler or installing a new system, the Baxi Potterton offers a perfect blend of practicality and innovation.
Top Page Image Contents