Sears 153.336262 40 GALLON SHORT, 153.336566 50 GALLON Temperature-Pressure Relief Valve

Page 14

Fit T & P valve insulation over valve. Make sure that the insulation does not interfere with the lever of the T & P valve.

Secure all insulation using tape.

Temperature-Pressure Relief Valve

This heater is provided with a properly certified combination temperature - pressure relief valve by the manufacturer.

The valve is certified by a nationally recognized testing laboratory that maintains periodic inspection of production of listed equipment as meeting the requirements for Relief Valves and Automatic Gas Shut-off Devices for Hot Water Supply Systems, ANSI Z21.22 and the code requirements of ASME.

If replaced, the valve must meet the requirements of local codes, but not less than a combination temperature and pressure relief valve certified as indicated in the above paragraph.

The valve must be marked with a maximum set pressure not to exceed the marked hydrostatic working pressure of the water heater (150 psi = 1,035kPa) and a discharge capacity not less than the water heater input rate as shown on the model rating plate.

For safe operation of the water heater, the relief valve must not be removed from its designated opening nor plugged.

The temperature-pressure relief valve must be installed directly into the fitting of the water heater designed for the relief valve. Position the valve downward and provide tubing so that any discharge will exit only within 6 inches (153 mm) above, or at any distance below the structural floor, see Figure 16. Be certain that no contact is made with any live electrical part. The discharge opening must not be blocked or reduced in size under any circumstances. Excessive length, over 30 feet (9.14 m), or use of more than four elbows can cause restriction and reduce the discharge capacity of the valve.

No valve or other obstruction is to be placed between the relief valve and the tank. Do not connect tubing directly to discharge drain unless a 6 inch air gap is provided. To prevent bodily injury, hazard to life, or property damage, the relief valve must be allowed to discharge water in quantities should circumstances demand. If the discharge pipe is not connected to a drain or other suitable means, the water flow may cause property damage.

FIGURE16.

The Discharge Pipe:

•Shall not be smaller in size than the outlet pipe size of the valve, or have any reducing couplings or other restrictions.

•Shall not be plugged or blocked.

•Shall be of material listed for hot water distribution.

•Shall be installed so as to allow complete drainage of both the temperature-pressure relief valve, and the discharge pipe.

•Shall terminate at an adequate drain.

•Shall not have any valve between the relief valve and tank.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Power Miser GAS Water Heater Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.ASafe INSTALLATION, USE and Service Important DefinitionsSafety Precautions Table of Contents Customer Responsibilities Product SpecificationsTo Install or Operate the Water Heater Materials Needed Additional Tools Needed When Sweat SolderingMaterials and Basic Tools Needed Basic ToolsPilot & Main Burner Typical InstallationThermostat Installation Instructions Removing the Old Water HeaterFacts to Consider About the Location Insulation Blankets ALL AIR from Inside Buildings See on page 9 and belowWater Piping Hotter Water can ScaldValve and Pipe Insulation Temperature-Pressure Relief Valve Filling the Water Heater VentingGas Piping GAS Piping with Flexible Connector Sediment TrapsFor Your Safety Read Before Lighting Operating InstructionsTemperature Regulation Temperature Time to Produce 2nd & 3rdBurner Cleaning Service and AdjustmentTank Sediment Cleaning Vent System InspectionAnode Rod Inspection Temperature-Pressure Relief Valve OperationHousekeeping DrainingDrain Valve Washer Replacement ServiceTroubleshooting Guide Start Up ConditionsOperational Conditions CondensationLeakage Checkpoints Troubleshooting Guide Page Page Burnerassembly Parts Order List153.336466 Gallon 153.336566 Burner Assembly 153.336962Warranty Service Year Limited Warranty on Water HeaterYear Exclusive Kenmore Labor Warranty

153.336466 40 GALLON, 153.336162, 153.336262 40 GALLON SHORT, 153.336762 30 GALLON PROPANE (L.P.), 153.336362 30 GALLON specifications

Sears offers a range of propane storage tanks designed to meet various domestic and commercial heating needs. Among the popular models are the 40-gallon propane tank (L.P.) with the model numbers 153.336862 and 153.336466, as well as the 50-gallon tank identified by 153.336566, and the 30-gallon propane tank represented by 153.336762. Each of these tanks incorporates modern technologies and features tailored for efficiency, safety, and convenience.

The 40-gallon propane tank is an excellent choice for homeowners looking to efficiently store fuel for heating applications, cooking, or outdoor entertainment. Its compact design allows for easy installation in smaller spaces while ensuring sufficient fuel capacity for moderate consumption needs. The tank is constructed from high-quality steel, providing durability and resistance against environmental factors, ensuring long-lasting service.

Sears also provides the 50-gallon propane tank for users with higher fuel demand. This model is essential for households with larger heating requirements or for businesses utilizing propane for cooking or heating. The larger capacity reduces the frequency of refills and enhances convenience for users.

On the other hand, the 30-gallon propane tank serves as a reliable option for customers with minimal fuel needs. Whether for heating specific areas or powering smaller outdoor appliances, this model offers ample capacity while remaining manageable in size.

Safety features are paramount in all Sears propane tanks. Each tank is equipped with safety valves that prevent over-pressurization, along with a robust design that minimizes the risk of leaks. These tanks also meet stringent safety standards, ensuring users confidence in their performance.

Additionally, all models feature external brackets for easy installation and securing to a solid foundation, reducing the risk of accidents during use or adverse weather conditions. The tanks are compatible with various propane appliances, ensuring versatility across applications.

In conclusion, Sears provides a selection of propane tanks that combine practicality with advanced safety features. Whether users opt for the 30-gallon, 40-gallon, or 50-gallon models, they can trust in the quality and reliability of Sears propane tanks to efficiently meet their fuel storage needs while maintaining safety as a top priority.
Top Page Image Contents