Insulation Blankets

Minimum clearances between the water heater and combustible construction are 0 inch at the sides and rear, 4 inches (102 mm) at the front, and 6 inches (153 mm) from the vent pipe, see Figure 8. Clearance from the top of the jacket is 12 inches (305 mm) on most models. Note that a lesser dimension may be allowed on some models, refer to the label attached adjacent to the gas control valve on the water heater.

FIGURE8.

A gas water heater cannot operate properly without the correct amount of air for combustion, see Figure 9. Do not install in a confined area such as a closet, unless you provide air as shown in the Locating The New Water Heater section. Never obstruct the flow of ventilation air. If you have any doubts or questions at all, call your gas supplier. Failure to provide the proper amount of combustion air can result in a fire or explosion and cause death, serious bodily injury, or property damage.

FIGURE9.

If this water heater will be used in beauty shops, barber shops, cleaning establishments, or self-service laundries with dry cleaning equipment, it is imperative that the water heater or water heaters be installed so that combustion and ventilation air be taken directly from outdoors (direct vent).

Propellants of aerosol sprays and volatile compounds, (cleaners, chlorine based chemicals, refrigerants, etc.) in addition to being highly flammable in many cases, will also change to corrosive hydrochloric acid when exposed to the combustion products of the water heater. The results can be hazardous, and also cause product failure.

Insulation blankets available to the general public for external use on gas water heaters are not necessary with Kenmore products. The purpose of an insulation blanket is to reduce the standby heat loss encountered with storage tank heaters. Your Kenmore water heater meets or exceeds the National Appliance Energy Conservation Act standards with respect to insulation and standby loss requirements, making an insulation blanket unnecessary.

WARNING

Should you choose to apply an insulation blanket to this heater, you should follow these instructions (See Figure 1 for identification of components mentioned below). Failure to follow these instructions can restrict the air flow required for proper combustion, potentially resulting in fire, asphyxiation, serious personal injury or death.

153.336466 40 GALLON, 153.336162, 153.336262 40 GALLON SHORT, 153.336762 30 GALLON PROPANE (L.P.), 153.336362 30 GALLON specifications

Sears offers a range of propane storage tanks designed to meet various domestic and commercial heating needs. Among the popular models are the 40-gallon propane tank (L.P.) with the model numbers 153.336862 and 153.336466, as well as the 50-gallon tank identified by 153.336566, and the 30-gallon propane tank represented by 153.336762. Each of these tanks incorporates modern technologies and features tailored for efficiency, safety, and convenience.

The 40-gallon propane tank is an excellent choice for homeowners looking to efficiently store fuel for heating applications, cooking, or outdoor entertainment. Its compact design allows for easy installation in smaller spaces while ensuring sufficient fuel capacity for moderate consumption needs. The tank is constructed from high-quality steel, providing durability and resistance against environmental factors, ensuring long-lasting service.

Sears also provides the 50-gallon propane tank for users with higher fuel demand. This model is essential for households with larger heating requirements or for businesses utilizing propane for cooking or heating. The larger capacity reduces the frequency of refills and enhances convenience for users.

On the other hand, the 30-gallon propane tank serves as a reliable option for customers with minimal fuel needs. Whether for heating specific areas or powering smaller outdoor appliances, this model offers ample capacity while remaining manageable in size.

Safety features are paramount in all Sears propane tanks. Each tank is equipped with safety valves that prevent over-pressurization, along with a robust design that minimizes the risk of leaks. These tanks also meet stringent safety standards, ensuring users confidence in their performance.

Additionally, all models feature external brackets for easy installation and securing to a solid foundation, reducing the risk of accidents during use or adverse weather conditions. The tanks are compatible with various propane appliances, ensuring versatility across applications.

In conclusion, Sears provides a selection of propane tanks that combine practicality with advanced safety features. Whether users opt for the 30-gallon, 40-gallon, or 50-gallon models, they can trust in the quality and reliability of Sears propane tanks to efficiently meet their fuel storage needs while maintaining safety as a top priority.