Sears 153.321342, 153.321842, 153.321442, 153.321643, 153.321543, 153.321642, 153.321843, 153.321343

Page 21

8.Clean the area around the element opening. Remove any sediment from or around the element opening, inside the tank.

9.If you are cleaning the element you have removed, do so by scraping or soaking in vinegar or a de-liming solution.

Never use this water heater unless it is completely full of water. To prevent damage to the tank and heating element, the tank must be filled with water. Water must flow from the hot water faucet before turning “ON” power.

14.Check element for water leaks. If leakage occurs, tighten element or repeat steps 2 and 3, remove element and reposition gasket. Then repeat steps 10 through 14.

15.Reconnect the two wires to the element and then check to make sure the thermostat remains firmly against the surface of the tank.

FIGURE 38.

16. Replace terminal cover on thermostat making sure that the locking tabs on the terminal cover are in place.

Replacement elements must (1) be the same voltage and (2) no greater wattage than listed on the model rating plate affixed to the water heater.

10.A new gasket should be used in all cases to prevent a possible water leak. (See Element Gasket in the “Repair Parts List ” Chart). Place the new element gasket on the thread side of the cleaned or new element and screw into tank, securing tightly using an element wrench.

FIGURE 37.

11.Close the water heater drain valve by turning the handle to the right (clockwise). The drain valve is on the lower front of the water heater.

12.Open the cold water supply valve to the water heater.

NOTE: The cold water supply valve must be left open when the water heater is in use.

13.To insure complete filling of the tank, allow air to exit by opening the nearest hot water faucet. Allow water to run until a constant flow is obtained. This will let air out of the water heater and the piping.

FIGURE 39.

17.Place the insulation cap with handle so that it completely covers the thermostat and element.

FIGURE 40.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A Power Misertm Electric Water HeaterSafe INSTALLATION, USE and Service General Safety Table of Contents Introduction Product SpecificationsMaterials and Basic Tools Needed Additional Tools Needed When Sweat SolderingMaterials Needed Basic ToolsRemoving the Old Water Heater Installation InstructionsFacts to Consider About the Location Insulation BlanketsFacts to Consider About Convertible Lower Element Water Piping Valve and Pipe Insulation Temperature-Pressure Relief ValveFilling the Water Heater Converting the Lower Element Page Wiring Page Wiring Diagrams Temperature Regulation Service and AdjustmentTemperature Settings Upper and Lower Thermostat AdjustmentsTemperature-Pressure Relief Valve Operation Anode Rod InspectionDraining Element Cleaning/Replacement Thermostat Removal/ReplacementPage Page Service Drain Valve Washer ReplacementTroubleshooting Start Up ConditionsOperational Conditions AIR in HOT Water Faucets Water is TOO HOT Leakage Checkpoints Model Numbers Repair Parts ListKenmore Power Misertm Electric Water Heaters Page Page Page MY-HOME

153.321443, 153.321442, 153.321643, 153.321342, 153.321842 specifications

The Sears models 153.321343, 153.321843, 153.321543, 153.321542, and 153.321642 represent a collection of versatile and innovative products that highlight Sears' commitment to quality and functionality. These models are notable for their distinct features and technologies that cater to a variety of consumer needs.

One of the main characteristics common to these models is their robust build quality. Each model is designed using durable materials that ensure longevity and resilience against wear and tear. This is particularly important for consumers looking for reliable products that can withstand daily use.

In terms of technological features, these models are equipped with advanced functionalities that enhance user experience. For instance, the inclusion of smart technology allows for seamless integration with home automation systems. This enables users to control aspects of the device through mobile applications or voice commands, ensuring convenience and accessibility.

Another noteworthy aspect is their energy efficiency. These models are designed with energy-saving features that help reduce overall power consumption without compromising performance. This is not only environmentally friendly but also translates to cost savings for consumers in the long run.

The versatility of the Sears models is evident in their wide range of applications. Each model is tailored to meet specific needs, whether for household tasks or specialized functions, making them suitable for a variety of users. This adaptability makes the models appealing to a broader audience, from casual users to more demanding consumers.

Moreover, these models often incorporate user-friendly interfaces. Easy-to-navigate controls and clear displays allow users to operate the devices without the need for extensive instructions, making them ideal for individuals of all ages and technological backgrounds.

Sears continues to provide exceptional customer support and warranty options with these models, further enhancing customer satisfaction and trust. This commitment to service ensures that buyers feel secure in their purchase, knowing they have support should any issues arise.

In conclusion, the Sears models 153.321343, 153.321843, 153.321543, 153.321542, and 153.321642 exemplify the brand's dedication to quality, innovation, and user-centered design. With their durable construction, advanced technology, energy efficiency, versatility, and strong customer support, they stand out in a competitive market, appealing to a wide range of consumers seeking reliable and multifunctional products.
Top Page Image Contents