Niles Audio RS 5s manual Speaker wire preparation, Speaker Phase

Page 12

INSTALLATION

4.Connect one stripped end of the speaker cable coming from the amplifier to the RS5 connection cable’s red wire. To connect the two wires, twist the stripped ends of the wire together and screw down the wire nut on the twisted wires. The material inside the wire nut will protect the stripped ends of the wire. However, if added protection is desired, place a large amount of silicone sealant so the bottom of the wire nut is encased and sealed. Pay attention to the markings on the speaker cable. Each loudspeaker you connect must be connected to the amplifier’s speaker wire in the same way.

5.Repeat step 4 with the RS5 connection cable’s black wire and the other stripped amplifier speaker cable’s conductor.

6.Connect the opposite end of the speaker cable to the amplifier or receiver. Start by performing step 1 and 2 on the speaker cable near the amplifier. Paying attention to the markings on the speaker cable conductor, attach the same conductor you attached to the red loudspeaker wire to the positive (red) or (+) amplifier output terminal. Attach the other conductor to the amplifier’s negative (black) or (–) amplifier output terminal.

Figure 6 Speaker wire preparation

Speaker Phase

Speaker wire has two conductors. One conductor is attached to the negative (black) or (-) terminals and one conductor is attached to the positive (red) or (+) terminals of both the loudspeaker and the amplifier. Usually, the wire is marked for your convenience. There are different ways to mark the conductor; a stripe on one wire, a ribbed area on one conductor that you can feel, different color metal conductor wire inside the insulation, the insulation covering the conductor might be different colors, or there might be a fabric string wound onto one of the conductors. Of course some cables make it difficult to determine which conductor is which. Be careful to avoid mistakes. If you do, one loudspeaker will be playing out of “phase” with the other loudspeaker. An out of phase pair of speakers work against each other and the sound of the two speakers playing together will be lacking in bass response and have a “phasey”sound quality. If you suspect the sound is not right,

11

Page 11 Page 13
Image 12
Page 11 Page 13
Contents RS5 Table of Contents Introduction Features & Benefits Connection Cable with Water Resistant Wire Nuts Precision CrossoverConeForward Design Rigid Acoustically Inert Cabinet ConstructionInstallation Considerations Tools and Materials RequiredSelecting the number and location for your speakers Stereo Coverage 6 speakers Installation Considerations Choosing the Speaker CableIncorporating a Volume Control 60 ft 18 m 100 ft 30 m 160 ft 50 mTwo Zone Volume Control Wiring Recommended Amplifier PowerInstallation Connecting the loudspeakerRun the speaker cable Speaker wire preparation Speaker PhaseVerify System Operation and Loudspeaker Coverage Installing the Security Bracket and Cable Security Cable in EyeletSecurity Stake Driven into Ground Upgraded Security Attachment Method Optional To install an upgraded security systemFinal Adjustments Listening at Higher Volumes CleaningOperation Specifications Nominal ImpedanceNiles Audio Corporation

RS 5s specifications

The Niles Audio RS 5s are a remarkable addition to any enthusiast’s audio setup, offering a blend of advanced technology, thoughtful design, and superior sound quality. These speakers are engineered to deliver an immersive audio experience, underpinned by a host of features that cater to both casual listeners and audiophiles alike.

One of the standout features of the RS 5s is their dynamic range. They incorporate a 5.25-inch woofer that delivers deep, rich bass, allowing for an expanded low-frequency response that enhances music and movie soundtracks alike. This woofer works in conjunction with a 1-inch silk dome tweeter, which ensures that high frequencies are reproduced with clarity and precision, resulting in a balanced sound profile that captures the nuances of the audio.

The construction of the RS 5s also contributes significantly to their performance. Designed with MDF cabinets, these speakers minimize resonance and distortion, promoting a cleaner sound output. The cabinets are finished with an attractive veneer that not only enhances aesthetic appeal but also reinforces durability. Additionally, the speakers come equipped with a rear-firing bass port that aids in delivering increased bass extension and responsiveness, allowing for greater flexibility in placement within a room.

Another noteworthy aspect of the Niles Audio RS 5s is their versatility. They are designed for both indoor and outdoor use, making them an excellent choice for various settings, from home theaters to backyard gatherings. The weather-resistant design ensures longevity when exposed to outdoor conditions, which is crucial for users who enjoy entertaining outside.

In terms of connectivity, the RS 5s support a range of integration options, allowing them to seamlessly connect with various audio systems, including multi-room setups. This compatibility makes them a smart choice for those looking to create a cohesive audio environment throughout their living spaces.

Overall, the Niles Audio RS 5s stand out due to their impressive sound quality, robust build, and innovative features that cater to a wide array of audio applications. Whether you're enjoying your favorite music or watching an action-packed movie, these speakers promise an engaging auditory experience that elevates your listening pleasure to new heights.
Top Page Image Contents