Hearth and Home Technologies 43M-ACC-MBK, 43ST-ACC warranty Installing Chimney Components

Page 18

4300 Wood Stove Series (ACC)

R

Solid Pack Chimney with Metal Supports as a Thimble (Cont’d)

Min. Chimney Clearance to

 

Wall Spacer and

Min. Clearance

Combustibles - 2 inch (51mm)

2 inch (51mm)

Chimney Flue

1 inch (25mm) Air

Space to Chimney

Liner

Section

Fireclay

Chimney

Liner or

Equivalent

Connector

 

Chimney Section

 

Trim Collar

 

Wall Band

Masonry Chimney

Wall Spacer

 

Constructed to NFPA 211

 

C. Installing Chimney Components

Chimney Connector

Single wall connector or stove pipe.

This must be at least 24 gauge mild steel or 26 gauge blue steel. The sections must be attached to the appliance and to each other with the crimped (male) end pointing toward the stove. All joints, including the connection at the flue collar, should be secured with 3 sheet metal screws. Make sure to follow the minimum clearances to combustibles. Where passage through the wall, or partition of combustible con- struction is desired in Canada, the installation shall conform to CAN/CSA-B365.

Factory-built listed chimney connector (vented).

A listed connector (vented) must be used when installing this unit in a mobile home. The listed connectors must conform to each other to ensure a proper fit and seal.

Figure 18.1

Chimney Height / Rise and Run

This product was designed for and tested on a 6 inch (152mm) chimney, 14 to 16 feet (420-480cm) high, (includes stove height) measured from the base of the appliance. The further your stack height or diameter varies from this configuration, the possibility of performance problems exists.

Chimney height may need to be increased by 2 - 3% per each 1000 feet above sea level. It is not recommended to use offsets or elbows at altitudes above 4000 feet above sea level or when there are other factors that affect flue draft.

Crimped

Flue Gas

End

Direction

Toward

 

Stove

 

Secure pipe sections with a

minimum of  screws

Figure 18.2 Chimney Connector (Stove Pipe)

WARNING

Fire Risk.

Inspection of Chimney:

Chimney must be in good condition.

Meets minimum standard of NFPA 211

Factory-built chimney must be 6 inch (152mm) UL103 HT.

WARNING

Asphyxiation Risk.

Do NOT connect this unit to a chimney flue servicing another appliance.

Do NOT connect to any air distribution duct or system.

May allow flue gases to enter the house.

WARNING

Fire Risk.

Follow Chimney Connector Manufacturer’s

Instructions for Proper Installation.

ONLY use connector:

Within the room, between appliance and ceiling or wall. Connector shall NOT pass through:

Attic or roof space

Closet or similar concealed space

Floor or ceiling

Maintain minimum clearances to combustibles

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appli- ance. For assistance or additional information consult a qualified installer, service agency or your dealer.

Page 18

7037-135E

September 1, 2008

Image 18
Contents 7037-135E September 1 Step Top Uni-Body Model Millennium ModelHot glass will cause burns Pedestal Model ShownWood Stove Series ACC Mfg. Date 7037-135E September 1Table of Contents Listing and Code Approvals Appliance Certification BTU & Efficiency SpecificationsGlass Specifications Mobile Home ApprovedFire Safety Getting StartedAppliance needs to draft properly for safety Wood Stove Series ACC Negative PressureTools And Supplies Needed Wood Stove Series ACC Flue Draft ConsiderationsVenting Systems Inspect Appliance & Components and Pre-Use Check ListWood Stove Series ACC Typical Stove Systems Masonry ChimneyDimensions and Clearances Appliance DimensionsMillennium Model 11/16 in mm 89mm Back of Stove to Glass 25-/8 645mm 10-/8 11/16170mm 264mmInstallation 90 Elbow Off Top of Stove Through Backwall Wood Stove Series ACC Clearances to Combustibles UL and ULCHearth Protection Requirements InstallationWood Stove Series ACC 4300 Millennium ModelWood Stove Series ACC Step-Top Uni-Body Model Wood Stove Series ACC Outside Air Kit Installation Items Needed for Installation not suppliedFire Risk Asphyxiation Risk Wood Stove Series ACC Blower Optional Shock RiskVenting Components Chimney Systems Chimney ConnectorChimney Requirements ThimbleInstructions ComponentsAir Clearances Solid Pack Chimney with Metal Supports as a ThimbleInstalling Chimney Components Solid Pack Chimney with Metal Supports as a Thimble Cont’dChimney Height / Rise and Run Pitched Roof Wood Stove Series ACC Chimney Termination RequirementsRule Flat RoofMobile Home Installation Appliance Set Up Begin installing the ARS SystemSlip wooden decorative strips onto pedestal edges Installing Pedestal AssemblyFinishing the ARS Installation Front cut bricks. FigureInstalling Leg Kit Corners. FigureWood Stove Series ACC Door Handle Assembly Adjusting The Blower Speed ControlBurning Process Operating InstructionsOver-Firing Your Appliance Wood Selection & Storage Cont’d Wood Selection & StorageAutomatic Combustion Control ACC Air ControlsBurn Rates and Operating Efficiency Wood Stove Series ACC Building a Fire Correct Position Wood Stove Series ACC Blower Operating Instructions Frequently Asked Questions Opacity SmokeInitial cold start-up and all Burn Settings Snap Disc LocationCreosote Chimney Cleaning General MaintenanceAsh Removal System ARS Operating and Cleaning Maintaining & Servicing Your ApplianceWhen cleaning glass Glass Cleaning Frequency As desiredCleaning Plated Surfaces Disposal of AshesWood Stove Series ACC Glass Replacement For the Millennium Model Wood Stove Series ACC Firebrick ReplacementAvailable for the Step Top Model and not To your authorized dealerWood Stove Series ACC Baffle Removal Snap Disc Replacement Snap Disc LocationWood Stove Series ACC Tube Channel Assembly Replacement Removing Tube Channel AssemblyReplacing Tube Channel Assembly Troubleshooting Start Fire Problems Possible Cause SolutionReference Materials Exploded viewDescription #33 Baffle Board 2 w x 15-3/4 h, each #29 Ceramic Blanket 19 w x 13-3/4 h, 1/2 thickStep-Top Uni-Body Model Door, Cast not sold separatelyWood Stove Series ACC Service Parts & Accessories Blower AssemblyItem # Service Parts Item # Service Parts Wood Stove Series ACC Service And Maintenance Log Date of Service Performed By Description of ServiceWood Stove Series ACC Homeowner’s Notes CONDITIONS, Exclusions & Limitation of Liability September 1 7037-135E Contact Information

43M-ACC-MBK, 43ST-ACC specifications

Hearth and Home Technologies has long been a leader in the design and manufacturing of high-quality heating appliances, and their models 43ST-ACC and 43M-ACC-MBK are no exception. These gas fireplaces combine aesthetic appeal with innovative technologies aimed at providing efficient heating solutions for residential spaces.

The 43ST-ACC is designed with versatility in mind. It features a traditional style that can seamlessly integrate into a variety of home decors. One of its standout characteristics is the expansive viewing area that allows homeowners to enjoy the mesmerizing flames. The fireplace utilizes advanced ceramic glass technology that enhances the thermal efficiency, ensuring a warm environment without compromising on safety.

On the technical side, the 43ST-ACC is equipped with the IntelliFire ignition system which provides convenient, reliable startup. This system also allows for enhanced safety features, ensuring the unit operates smoothly and safely. The adjustable flame height and heat output settings further allow users to create their desired ambiance while optimizing fuel consumption.

Additionally, the 43M-ACC-MBK model is geared towards those who appreciate a modern, sophisticated design. This model is characterized by its sleek, black finish and clean lines, making it an eye-catching centerpiece in any room. Like the 43ST-ACC, it also boasts an impressive viewing area, but it comes with the added benefit of customizable features, including remote control operation and programmable thermostats.

Both models are designed with efficiency in mind, incorporating technology that maximizes heat distribution throughout the room. Their direct vent operation ensures that combustion gases are exhausted outside, making them a safe choice for indoor spaces. The inclusion of a blower system in both models enhances air circulation, providing an even distribution of warmth throughout the environment.

In conclusion, the Hearth and Home Technologies 43ST-ACC and 43M-ACC-MBK gas fireplaces combine style, functionality, and advanced technology. Whether you are looking for a traditional touch or a modern flair, these models cater to diverse preferences while ensuring efficient heating and safety. With their innovative features and beautiful designs, they truly represent the pinnacle of home heating solutions. Whether settling in for a cozy evening or entertaining guests, these fireplaces are sure to enhance any living space.