Hearth and Home Technologies 43M-ACC-MBK Chimney Requirements, Venting Components Chimney Systems

Page 16

4300 Wood Stove Series (ACC)

R

 

Chimney Requirements

 

Venting Components

B. Chimney Systems

A.5

 

Chimney Connector:

Prefabricated Metal Chimney

 

It is also known as flue pipe or stove pipe. The chimney connector joins the stove to the chimney. It must be a 6 inch (152mm) minimum diameter 24 gauge mild steel black or 26 gauge blued steel, or an approved air-insulated double wall venting pipe.

Thimble:

A manufactured or site-constructed device installed in combustible walls through which the chimney connector passes to the chimney. It is intended to keep the walls from igniting. Site constructed thimbles must meet NFPA 211 Standards. Prefabricated must be suitable for use with selected chimney and meet UL103 Type HT Standards. Follow instructions provided by the manufacturer for manufactured thimbles for masonry chimney and prefabricated chimneys.

Chimney:

The chimney can be new or existing, masonry or prefabricated and must meet the following minimum requirements specified in Section 5B.

Listed Termination Cap

Roof Brace (if required)

Storm Collar

 

Flashing

Trim Collar on

Listed Chimney

Inside Wall

Insulated "T "

 

Chimney

Wall Support

Connector

 

 

Thimble

Floor

 

Protector

 

•Must be a 6 inch (152mm) diameter (ID) high temperature chimney listed to UL 103 HT (2100oF) or ULC S629M.

•Must use components required by the manufacturer for installation.

•Must maintain clearances required by the manufacturer for installation.

•Refer to manufacturers instructions for installation.

NOTE: In Canada when using a factory-built chimney it must be safety listed, Type UL103 HT (2100oF) CLASS “A” or conforming to CAN/ULC-S629M, STANDARD FOR 650oC

FACTORY-BUILT CHIMNEYS.

Listed Termination Cap

Storm Collar

Flashing

Listed Chimney

Ceiling Support

Chimney

Connector

Floor

Protector

Figure 16.1 Prefabricated Exterior Chimney

Figure 16.2 - Prefabricated Interior Chimney

Page 16

7037-135E

September 1, 2008

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Step Top Uni-Body Model Millennium Model Hot glass will cause burns7037-135E September 1 Pedestal Model ShownWood Stove Series ACC Mfg. Date 7037-135E September 1Table of Contents Appliance Certification BTU & Efficiency Specifications Glass SpecificationsListing and Code Approvals Mobile Home ApprovedFire Safety Getting StartedAppliance needs to draft properly for safety Wood Stove Series ACC Negative PressureWood Stove Series ACC Flue Draft Considerations Venting SystemsTools And Supplies Needed Inspect Appliance & Components and Pre-Use Check ListWood Stove Series ACC Typical Stove Systems Masonry ChimneyAppliance Dimensions Dimensions and ClearancesMillennium Model 11/16 170mm11/16 in mm 89mm Back of Stove to Glass 25-/8 645mm 10-/8 264mmInstallation 90 Elbow Off Top of Stove Through Backwall Wood Stove Series ACC Clearances to Combustibles UL and ULCInstallation Wood Stove Series ACC 4300Hearth Protection Requirements Millennium ModelWood Stove Series ACC Step-Top Uni-Body Model Items Needed for Installation not supplied Wood Stove Series ACC Outside Air Kit InstallationFire Risk Asphyxiation Risk Wood Stove Series ACC Blower Optional Shock RiskChimney Connector Chimney RequirementsVenting Components Chimney Systems ThimbleComponents Air ClearancesInstructions Solid Pack Chimney with Metal Supports as a ThimbleSolid Pack Chimney with Metal Supports as a Thimble Cont’d Installing Chimney ComponentsChimney Height / Rise and Run Wood Stove Series ACC Chimney Termination Requirements RulePitched Roof Flat RoofMobile Home Installation Appliance Set Up Begin installing the ARS SystemInstalling Pedestal Assembly Finishing the ARS InstallationSlip wooden decorative strips onto pedestal edges Front cut bricks. FigureInstalling Leg Kit Corners. FigureWood Stove Series ACC Door Handle Assembly Adjusting The Blower Speed ControlOperating Instructions Over-Firing Your Appliance Wood Selection & Storage Cont’dBurning Process Wood Selection & StorageAutomatic Combustion Control ACC Air ControlsBurn Rates and Operating Efficiency Wood Stove Series ACC Building a Fire Correct Position Frequently Asked Questions Opacity Smoke Initial cold start-up and all Burn SettingsWood Stove Series ACC Blower Operating Instructions Snap Disc LocationGeneral Maintenance Ash Removal System ARS Operating and CleaningCreosote Chimney Cleaning Maintaining & Servicing Your ApplianceGlass Cleaning Frequency As desired Cleaning Plated SurfacesWhen cleaning glass Disposal of AshesWood Stove Series ACC Glass Replacement Wood Stove Series ACC Firebrick Replacement Available for the Step Top Model and notFor the Millennium Model To your authorized dealerWood Stove Series ACC Baffle Removal Snap Disc Replacement Snap Disc LocationRemoving Tube Channel Assembly Wood Stove Series ACC Tube Channel Assembly ReplacementReplacing Tube Channel Assembly Troubleshooting Start Fire Problems Possible Cause SolutionExploded view Reference MaterialsDescription #33 Baffle Board 2 w x 15-3/4 h, each #29 Ceramic Blanket 19 w x 13-3/4 h, 1/2 thickStep-Top Uni-Body Model Door, Cast not sold separatelyWood Stove Series ACC Service Parts & Accessories Blower AssemblyItem # Service Parts Item # Service Parts Wood Stove Series ACC Service And Maintenance Log Date of Service Performed By Description of ServiceWood Stove Series ACC Homeowner’s Notes CONDITIONS, Exclusions & Limitation of Liability September 1 7037-135E Contact Information

43M-ACC-MBK, 43ST-ACC specifications

Hearth and Home Technologies has long been a leader in the design and manufacturing of high-quality heating appliances, and their models 43ST-ACC and 43M-ACC-MBK are no exception. These gas fireplaces combine aesthetic appeal with innovative technologies aimed at providing efficient heating solutions for residential spaces.

The 43ST-ACC is designed with versatility in mind. It features a traditional style that can seamlessly integrate into a variety of home decors. One of its standout characteristics is the expansive viewing area that allows homeowners to enjoy the mesmerizing flames. The fireplace utilizes advanced ceramic glass technology that enhances the thermal efficiency, ensuring a warm environment without compromising on safety.

On the technical side, the 43ST-ACC is equipped with the IntelliFire ignition system which provides convenient, reliable startup. This system also allows for enhanced safety features, ensuring the unit operates smoothly and safely. The adjustable flame height and heat output settings further allow users to create their desired ambiance while optimizing fuel consumption.

Additionally, the 43M-ACC-MBK model is geared towards those who appreciate a modern, sophisticated design. This model is characterized by its sleek, black finish and clean lines, making it an eye-catching centerpiece in any room. Like the 43ST-ACC, it also boasts an impressive viewing area, but it comes with the added benefit of customizable features, including remote control operation and programmable thermostats.

Both models are designed with efficiency in mind, incorporating technology that maximizes heat distribution throughout the room. Their direct vent operation ensures that combustion gases are exhausted outside, making them a safe choice for indoor spaces. The inclusion of a blower system in both models enhances air circulation, providing an even distribution of warmth throughout the environment.

In conclusion, the Hearth and Home Technologies 43ST-ACC and 43M-ACC-MBK gas fireplaces combine style, functionality, and advanced technology. Whether you are looking for a traditional touch or a modern flair, these models cater to diverse preferences while ensuring efficient heating and safety. With their innovative features and beautiful designs, they truly represent the pinnacle of home heating solutions. Whether settling in for a cozy evening or entertaining guests, these fireplaces are sure to enhance any living space.
Top Page Image Contents