LG Electronics EN 61000-3, EN 61000-2 owner manual Auto operation Optional, During Auto Operation

Page 15

Auto operation (Optional)

1

Press the Start/Stop button.

The unit will respond with

a beep.

Operating Instruction

ENGLISH

2

Open the door of the remote controller. To select Auto

Operation, press the operation mode selection button.

Each time the button is pressed, the operation mode is shifted in the direction of the arrow.

Cooling

Auto

Healthy

Heating

 

 

Dehumidification

(Heat pump model only)

ON

3

The temperature and fan speed are automatically set by the

electronic controls based on the actual room temperature. If

you want to change the set temperature, press the Room Temperature Setting buttons. The cooler or warmer you feel, the more times (up to two times) you should press the button. The set temperature will be changed automatically.

To raise the temperature

To lower the temperature

During Auto Operation

❏You cannot control the indoor fan speed. It has already been set by the Fuzzy rule.

❏If the system is not operating as desired, manually switch to another mode. The system will not automatically switch from the cooling mode to the heating mode, or from heating mode to cooling mode, it must be done by manually resetting.

❏During Auto Operation, pressing the CHAOS swing button makes the horizontal louvers swing up and down automatically. If you want to stop auto-swing, press the CHAOS swing button again.

Owner’s Manual 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Room Air Conditioner Table of Contents There is risk of electric shock Safety PrecautionsBe sure not to do Be sure to follow the instruction There is risk of fire or electric shockExplosion, or injury Damage to the product Edges Could cause personal injury Personal injuryShock There is risk of electrical shock There is risk of fire or product failureOxygen deficiency could occur There is risk of explosion or fireTo avoid vibration or water leakage It may cause a problem for your neighborsThere is risk of fire or electrical shock Bad connection may cause water leakageThere is risk of personal injury Avoid personal injuryThis could damage your health ProductBe careful and avoid personal injury There is risk of fire or explosionThey may burn or explode Usage ServicePrior To Operation Preparing For OperationIndoor Symbols Used In This ManualFeatures IntroductionElectrical Safety Operating Instruction Controls Remote Control OperationsGentle Breeze by the Chaos logic Cooling operationDuring Auto Operation Auto operation OptionalDuring Auto Changeover Operation Auto changeover operationOptionalFan speed mode is shifted Healthy dehumidification operationDuring Healthy Dehumidification Operation Heating operation Heat pump model only Close the door of the remote controllerTemperature can be set within a range Remote controller still closed. You canJet cool operation NEO Plasma Air Purifying Operation only NEO Plasma purification operationOptionalButton is pressed again 2nd F operationDelay start/Pre-set stop Additional FeaturesSleep mode Setting the timeVertical Airflow Direction Control Adjust the left/right airflow direction by hand22C71.6F 23C73.4F 24C75.2F Auto clean OptionalForced operation Test operationHelpful information To disable functionTo enable function Auto restartIndoor Unit Maintenance And ServiceAir conditioner is operating normally when Outdoor UnitAir conditioner does not cool as it should TroubleshootingAir conditioner may be operating abnormally when Air conditioner does not start
Related manuals
Manual 27 pages 36.57 Kb Manual 29 pages 29.82 Kb

EN 61000-3, EN 61000-2 specifications

LG Electronics is committed to delivering cutting-edge technology while ensuring compliance with international standards. Among these standards are the EN 61000-2 and EN 61000-3 norms, which address electromagnetic compatibility (EMC) and are critical in defining how electrical and electronic devices interact with their electromagnetic environment.

EN 61000-2 focuses on the environment within which devices operate. This standard outlines the general requirements for the compatibility of various electrical devices in residential, commercial, and industrial environments. It specifies the necessary electromagnetic interference (EMI) levels to protect devices from disturbances that could impact their functionality. For LG Electronics, adherence to EN 61000-2 means engineering products that minimize the potential for EMI disruptions, thereby ensuring reliable performance in diverse settings.

On the other hand, EN 61000-3 addresses the emission limits for harmonic currents in electrical systems and equipment. It focuses on ensuring that devices do not generate excessive current harmonics that could disrupt the normal operation of other equipment. For LG, compliance with EN 61000-3 involves implementing technologies that reduce harmonic distortion, which improves the overall power quality in electrical systems. This aspect is particularly important for ensuring energy efficiency and enhancing the longevity of both LG products and the systems they are integrated into.

One of the main features of LG’s products that adhere to these standards is the incorporation of advanced filtering technologies. These filters are designed to suppress harmful electromagnetic emissions and ensure that devices operate within permissible limits. Furthermore, LG employs superior circuit designs that prioritize efficient power management, helping to minimize harmonic generation.

Moreover, LG’s commitment to sustainability is reflected in its adherence to these norms. By reducing electromagnetic emissions and improving power quality, LG Electronics not only complies with regulations but also contributes to a greener environment. This aligns with the company’s broader vision of producing environmentally friendly and energy-efficient products.

In summary, LG Electronics continuously invests in technologies that ensure compliance with EN 61000-2 and EN 61000-3 norms. Through advanced filtering solutions and efficient circuit designs, the company demonstrates its dedication to electromagnetic compatibility, reliability, and sustainability, reinforcing its position as a leader in the global electronics market.
Top Page Image Contents