LG Electronics P1BRENTW-A Outside AIR KIT Optional, Outside Air Installation

Page 21

3.6OUTSIDE AIR KIT (Optional)

During operation, the fireplace requires fresh air for combustion and draws air out of the house. It may starve other fuel burning appliances such as gas or oil furnaces. As well, exhaust fans may compete for air, causing negative pressure in the house, resulting in smoke entering the house from the fireplace. This situation is aggravated in modern airtight houses. To overcome this problem, we strongly recommend that you install an outside air assembly. Check with local authorities having jurisdiction in your area, it may be mandatory.

NOTE: Should you decide not to install the outside air assembly, proceed as follows:

-Remove the bottom grill. The air box is located on front left and is on a slant.

-Unscrew the four screws holding the inside air box covering plate and remove it.

3.6.1Outside Air Installation

The outside air assembly may be installed according to the following requirements :

A)Duct length should be kept to a minimum. The maximum length of duct is 20 ft. (6.1 m) for a 4 in. dia. pipe (See note below).

B)The air intake register must not be installed more than 10 ft. (3050 mm) above the base of the fireplace.

C)The fresh air must come from outside the house. The air intake must not draw air from the attic, from the basement or garage.

D)The air intake should be installed where it is not likely to be blocked by snow or exposed to extreme wind and away from automobile exhaust fumes, gas meters and other vents.

E)The duct and register may be installed above or below floor level.

The following components are required : - Outside air kit (UZI)

- 4" adapter for fireplace connection (supplied with the unit)

Make a 4 ¼" (110 mm) hole in the outside wall of the house at the chosen location. From outside, place the outside air register in the hole (open side down) and fasten the register to the wall, with screws as shown (see figure 18). Slip the pipe into the insulated sleeve. Place the insulated pipe over the register tube and over the fireplace’s outside air connector (see figure 19). At each end, carefully pull back the insulation and plastic cover exposing the flexible pipe. Using the aluminium tape provided, wrap the tape around the joint between the flexible pipe and the air inlets. Carefully push the insulation and plastic cover back over the pipe. Using aluminium tape, fasten the plastic cover in place.

NOTE: We recommend not to exceed 20 feet of 4” flexible pipe. If you require a longer length we recommend that you use a 5” diameter flexible pipe for the complete run up to 30 feet and a 6” diameter pipe for a run of up to 40 feet.

Figure 18

Figure 19

19

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Brentwood Table of Contents Safety Rules for Operating Your Fireplace Model Brentwood Certification Label Introduction Parts RequiredAdditional Equipment optional Fuel Operating the BrentwoodFirst Fires Building a FireAccelerated Combustion Primary Air and Air Boost ControlsMedium Combustion Slow CombustionRefuelling For Best Performance Negative pressure in the house Smoking Causes and TroubleshootingImportant Notes Chimney MaintenanceDealing With a Chimney Fire Top Baffle Removal Prior to Cleaning The ChimneyFinish Door Casing Care AshesDoor Installation Refractory ReplacementGlass Care Replacement Door AdjustmentGlass Care Cleaning Gasket ReplacementFireplace Installation Locating The BrentwoodHearth Extension Requirements Framing, Facing And Mantel Insulated Chase Construction Mantel Gravity Kit HOT AIR Ducting InstallationPage Duct system must be installed respecting the following Outside AIR KIT Optional Outside Air InstallationAC Chimney Outside AIR KIT Optional Chimney Chimney Installation NotesChimney Square Hole Size Chimney Installation InstructionsAC Chimney Installation AIR Cooled Galvalume Chimney Roof Down Slope Hole Size Brentwood Offset Chimney InstallatonPage Angled Wall Radiation Shield ACRSM30, ACRSMI30 Chimney Chase and Multiple Terminations Chimney Support InstallationPage Parts and Components List AC Chimney Options Appendix

P1BRENTW-A specifications

LG Electronics has consistently been at the forefront of technological innovation, and the P1BRENTW-A is a prime example of its commitment to quality and performance. This air conditioning unit is engineered to provide optimal indoor climate control, ensuring comfort in a variety of environments.

One of the standout features of the P1BRENTW-A is its energy-efficient design. With a high Energy Efficiency Ratio (EER), it minimizes electricity consumption while delivering powerful cooling capabilities. The unit is equipped with a dual inverter compressor, which adjusts its cooling capacity according to the temperature in the room, enhancing energy savings while maintaining a consistently comfortable temperature.

The P1BRENTW-A also boasts a variety of smart technologies that enhance user experience. Its Wi-Fi connectivity allows users to control the unit remotely through a smartphone app. This functionality means that homeowners can adjust settings, monitor energy usage, and schedule operation times even when they are not at home, all contributing to greater convenience and efficiency.

In addition, the air conditioning unit features a multi-functional air purification system. This system includes a high-efficiency particulate air (HEPA) filter that captures dust, allergens, and other particles, making the air cleaner and healthier to breathe. The inclusion of a dehumidifying function helps to maintain a balance in humidity levels, preventing excessive moisture buildup that can lead to mold growth and discomfort.

Installation of the P1BRENTW-A is made straightforward with LG's user-friendly design. It is suitable for a variety of spaces, including residential areas, office environments, and commercial spaces. The sleek and modern aesthetic of the unit ensures that it blends well with contemporary interior designs.

Moreover, the LG P1BRENTW-A is built for long-lasting durability, featuring high-quality materials that withstand the test of time. It undergoes rigorous testing to ensure reliability and performance in varying environmental conditions. Additionally, the unit includes a few operational modes, providing flexibility to users depending on their cooling or heating needs.

In summary, the LG Electronics P1BRENTW-A stands out for its energy efficiency, smart technologies, superior air purification capabilities, and user-friendly design. Whether for personal comfort or maintaining a suitable work environment, this air conditioning unit offers a well-rounded solution for modern indoor climate control needs.
Top Page Image Contents