Sears 139.53627SRT, 139.53636SRT, 139.53641SRT, 139.53525SRT, 139.53640SRT Fasten Door Bracket

Page 24

Installation Step 11

Fasten Door Bracket

Follow instructions which apply to your door type as illustrated below or on page 25.

To prevent damage to steel, aluminum,

fiberglass or glass panel doors, always reinforce the inside of the door both vertically and horizontally with an angle iron.

A horizontal brace should be long enough to be secured to 2 vertical supports. A vertical brace should cover the height of the top panel.

The illustration shows one piece of angle iron as the horizontal brace. For the vertical brace, 2 pieces of angle iron are used to create a "U"-shapedsupport. The best solution is to check with your garage door manufacturer for an opener installation door reinforcement kit.

Header

/ Bracket

Door

reinforcement

is needed for lightweight garage doors

(fiberglass, aluminum, steel,Figure 1 doors with glass paeet, etc).

Bracket

Location

\

Carriage BoIt 5/16"-18x2-1/2"

Lock Washer 5/16"

•Center the door bracket on the previously marked vertical guideline used for the header bracket installation.

Door

Bracket j_

Nut/

Vertical _ 5/16"-18

Guideline

Figure 2

Inside Ed(

of Door or

Reinforcement Board

Door

Door Bracket

Plate

•Position the bracket on the face of the door within the following limits:

A)The top edge of the bracket 2"-4" below the top edge of the door.

B)The top edge of the bracket directly below any structural support across the top of the door.

•Mark and drill 5/16" left and right fastening holes.

Secure the bracket as shown in Figure 1 if there is vertical reinforcement.

If your installation doesn't require vertical reinforce- ment but does need top and bottom fastening holes for the door bracket, position the door plate over the door bracket as shown in Figure 2. Fasten securely with hardware shown in Figure 11

Hardware Shown Actual Size

© ©

Nut 5/16-18

Lock Washer 5/16"

Carriage Bolt 5/16"-18x2-1/2"

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents
Sears Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.AStart by reviewing these important safety alert symbols Installation Section pages 11Mechanical Electrical Youll Need Tools IArm One-Piece Door without Track One-Piece Door with TrackBefore you begin, survey your garage area to Closed PositionEndsections Opener Carton inventoryAssembly Hardware Installation HardwareSafety Reversing InstallationAssembly Section Pages 8 Assembly StepAssembly Step Install the Trolley on the T-railFasten the T-rail to the Opener Hardware Shown Actual SizeLinkBar Figure To make Sure the chain is notTwisted To attach the sprocket coverImportant Installation Instructions Tighten the Chain & CableProceed to , RememberOne-piecedoor without track jamb hardware One-piecedoor without track Pivot hardwareInstallation Step Install the Header BracketFasten the Header Bracket to the Wall Fasten the Header Bracket to the CeilingAttach the T-rail to the Header Bracket Tro, y Position the OpenerTwo representative installations are shown Nstallation StepHang the Opener Install the Deluxe Lighted Console Wall Control See Safety Reversing Sensor Instructions beginning onOutdoor Key Switch Accessory Connections Clearly, and there are no obstructions to door travelInstall the Lights and the Lenses Install the lightsInstall the lenses Attach Emergency Release Rope Handle Wiring Electrical Requirements Connections PermanentSafety Reversing System Facing the door from inside the garageInstall the Safety Reversing Sensor Alternate Floor MountTrouble Shooting Push Connector Wire Connector Until You hear a clickFasten Door Bracket Finished Ceiling Connect Door Arm to Trolley Hole Alignment AlternativeAdjustment Procedures for One-Piece Doors Assemble the Door ArmDecrease UP limit Connect the door arm to the trolleyAdjustment Section Pages 28 Adjustment Step Adjust the UP and Down LimitsTo Adjust the Limits How and WhenAdjust the Force To Adjust the ForcesTest the UP open force If the door doesnt open at least 5 feetTest The Safety Reversing Sensor Test the Safety Reverse SystemImportant safety check Maintenance Remote control batteryDispose of your old battery properly Care of Your OpenerOperation of Your Opener Operation of the Deluxe Lighted Console Wall ControlReceiver and Remote Control Programming Mini 3-Function Remote ControlTo Add a Remote Control To Erase All Remote control CodesHaving a Problem? Situation Probable Cause and SolutionSituationProbable Cause & Solution Door opens butRepair Parts Installation PartsOpener Assembly Parts 1918Accessories Index For the repair or replacement parts you need For the location of a
Top Page Image Contents