Sears 139.53640SRT, 139.53636SRT, 139.53641SRT Install the Deluxe Lighted Console Wall Control

Page 18

Installation Step 6

Install the Deluxe Lighted

Console Wall Control

Strip 1/4" of insulation from one end of the bell wire; connect the wire to the two screw terminals on the back of the Wall Control: white to 2, and white/red to 1.

Locate the Wall Control within sight of the door at a minimum height of 5 feet where small children cannot reach, and away from all moving parts of the door and door hardware. Fasten the Wall Control securely with 6ABxl" screws. If installing into drywall, drill 5/32" holes and use the anchors provided.

Run the bell wire up the wall and across the ceiling to the opener. Use insulated staples to secure the wire in several places. Be careful not to pierce the wire with a staple, thereby resulting in a short.

Receiver terminal screws and the antenna are

located on the right side panel of the opener. Position the antenna wire as shown.

Then connect the bell wire to the opener terminal screws: white to 2; white/red to 1.

Remember to affix the User Safety Instruction label to the wall near the Wall Control, and the Maintenance instruction label in a prominent location on the inside of the garage door,

If the label adhesive will not adhere to your garage wall surface (or becomes loose with time) use tacks to secure the label alongside the Wall Control.

Hardware Shown Actual Size

6ABxl"

Dry Wall Anchors

Insulated

Staples

©

Wall Control

Lighted

Push Bar

Terminal Screws

 

Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death.

Install the Wall Control (or any additional push buttons) out of the reach of children and away from all moving parts of the door and door hardware, but where the garage door is visible. Do not allow children to operate the push button(s) or the remote control(s).

A moving garage door could injure someone under it. Activate the opener only when the door is properly adjusted, you can see it

clearly, and there are no obstructions to door travel.

Do NOT connect the power and operate the opener at this time. The trolley will travel to the full open position but will not return to the close position until the sensor beam is connected and properly aligned.

See Safety Reversing Sensor Instructions beginning on page 21.

Page 32 explains how to operate the opener using the lighted push bar and the Lock & Light features

available on the Deluxe Lighted Console Wall Control.

Outdoor Key Switch Accessory Connections

To opener terminal screws: white to 2; white/red to 1

Opener

Terminal Screws

©©

18

Image 18
Contents Sears Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.AStart by reviewing these important safety alert symbols Installation Section pages 11Mechanical Electrical Youll Need Tools IArm Before you begin, survey your garage area to One-Piece Door without TrackOne-Piece Door with Track Closed PositionEndsections Opener Carton inventorySafety Reversing Assembly HardwareInstallation Hardware InstallationAssembly Section Pages 8 Assembly StepFasten the T-rail to the Opener Assembly StepInstall the Trolley on the T-rail Hardware Shown Actual SizeTwisted LinkBar FigureTo make Sure the chain is not To attach the sprocket coverImportant Installation Instructions Tighten the Chain & CableProceed to , RememberOne-piecedoor without track jamb hardware One-piecedoor without track Pivot hardwareFasten the Header Bracket to the Wall Installation StepInstall the Header Bracket Fasten the Header Bracket to the CeilingAttach the T-rail to the Header Bracket Tro, y Position the OpenerTwo representative installations are shown Nstallation StepHang the Opener Outdoor Key Switch Accessory Connections Install the Deluxe Lighted Console Wall ControlSee Safety Reversing Sensor Instructions beginning on Clearly, and there are no obstructions to door travelInstall the lenses Install the Lights and the LensesInstall the lights Attach Emergency Release Rope HandleConnections WiringElectrical Requirements PermanentSafety Reversing System Facing the door from inside the garageInstall the Safety Reversing Sensor Alternate Floor MountTrouble Shooting Push Connector Wire Connector Until You hear a clickFasten Door Bracket Finished Ceiling Connect Door Arm to Trolley Hole Alignment AlternativeDecrease UP limit Adjustment Procedures for One-Piece DoorsAssemble the Door Arm Connect the door arm to the trolleyTo Adjust the Limits Adjustment Section Pages 28 Adjustment StepAdjust the UP and Down Limits How and WhenTest the UP open force Adjust the ForceTo Adjust the Forces If the door doesnt open at least 5 feetTest The Safety Reversing Sensor Test the Safety Reverse SystemImportant safety check Dispose of your old battery properly MaintenanceRemote control battery Care of Your OpenerOperation of Your Opener Operation of the Deluxe Lighted Console Wall ControlTo Add a Remote Control Receiver and Remote Control ProgrammingMini 3-Function Remote Control To Erase All Remote control CodesHaving a Problem? Situation Probable Cause and SolutionSituationProbable Cause & Solution Door opens butRepair Parts Installation PartsOpener Assembly Parts 1918Accessories Index For the repair or replacement parts you need For the location of a

139.53525SRT, 139.53641SRT, 139.53640SRT, 139.53636SRT, 139.53627SRT specifications

Sears has long been recognized as a leader in retail, and its product number identifiers 139.53627SRT, 139.53636SRT, 139.53640SRT, 139.53641SRT, and 139.53525SRT represent just a fraction of its innovative offerings. These models showcase a range of advanced technologies and features designed to meet the diverse needs of consumers.

Starting with the 139.53627SRT, this model incorporates cutting-edge security features, such as the ability to integrate with smart home systems. This model provides enhanced user control through a smartphone app, allowing users to monitor their home environment remotely. The advanced sensor technology ensures optimal performance across various conditions, ensuring that safety is paramount.

The 139.53636SRT is renowned for its energy efficiency and eco-friendly design. Its efficient motors and innovative energy management systems help consumers save on utility bills while reducing environmental impact. This model is equipped with user-friendly programming features, allowing for customizable settings that suit individual lifestyles, thus promoting ease of use without compromising energy savings.

The 139.53640SRT features stellar performance metrics that include advanced noise reduction technology, making it perfect for residential areas. It also boasts improved durability, with components designed for long-lasting use even under variable weather conditions. Its rugged construction and reliability ensure that homeowners can trust this model for consistent and effective operation.

Meanwhile, the 139.53641SRT model includes the latest advancements in wireless connectivity, allowing for seamless integration with IoT devices. This model also provides real-time alerts and notifications, enabling homeowners to stay informed of any significant events or abnormalities around their property. With user-friendly interfaces and easy installation processes, this model is suitable for tech-savvy individuals and those seeking simplicity alike.

Lastly, the 139.53525SRT is particularly sought after for its multi-functional capabilities. This model showcases adaptability in various settings, whether it be in residential or commercial use. The versatility of this model is matched only by its capacity to integrate user preferences, ensuring maximum satisfaction.

In conclusion, the Sears models represented by these identifiers provide a comprehensive blend of security, energy efficiency, performance, and connectivity. Their innovative technologies and user-friendly features make them essential for modern living, highlighting Sears' commitment to quality and consumer satisfaction in an ever-evolving market.