Sears 139.53930D owner manual Install the Light, Attach the Emergency Release Rope and Handle

Page 18

INSTALLATION STEP 7

Install the Light

•Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens.

•Install up to a 100 watt maximum light bulb in the socket. The light will turn ON and remain lit for approximately 4-1/2 minutes when power is connected. Then the light will turn OFR

•Reverse the procedure to close the lens.

•Use A19, standard neck garage door opener bulbs for replacement.

NOTE: Use only a standard light bulb. The use of short neck or speciafity light bulb may overheat the endpanel or light socket.

INSTALLATION STEP 8

Attach the Emergency Release Rope and Handle

•Thread one end of the rope through the hole in the top

of the red handle so "NOTICE" reads right side up as shown. Secure with an overhand knot at least 1"

(2.5 cm) from the end of the rope to prevent slipping.

•Thread the other end of the rope through the hole in the release arm of the outer trolley.

•Adjust rope length so the handle is 6 feet (1.83 m) above the floor. Ensure that the rope and handle clear the tops of all vehicles to avoid entanglement. Secure with an overhand knot.

NOTE: If it is necessary to cut the rope, heat seal the cut end with a match or lighter to prevent unraveling.

To prevent possible OVERHEATINGof the endpanelor light socket,

•DO NOTuse short neck or specialty light bulbs.

•DO NOTuse halogen bulbs. Use ONLYincandescent. To prevent damage to the opener:

•DO NOTuse bulbs larger than IOOW.

•ONLYuse A19 size bulbs.

100 Watt (Max)

Standard

Light Bulb

Release Tab

\\

To prevent possible SERIOUSINJURYor DEATHfrom a failing garage door:

•If possible, use emergency releasehandle to disengage trolley ONLYwhen garagedoor is CLOSED.Weak or broken springs or unbalanceddoor could result in an open door failing rapidly and/or unexpectedly.

•NEVERuse emergency releasehandle unless garage doorway is clear of persons and obstructions.

•NEVERuse handleto pull door open or closed. If rope knot becomes untied,you could fall.

Trolley

Emergency

_K Overhand

 

Release Handle

not

 

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents 315N= Garage Door Opener Abridor DE Puerta DE Cochera 315.= Contents IntroductionTools needed Preparing your garage doorSectional Door Installation Sectional Door InstallationsPlanning ONE-PIECE Door Installations ONE-PIECE Door Without TrackONE-PIECE Door with Track Carton Inventory Secu RITY,IAssembly Hardware Installation HardwareHardware Inventory Assembly Step Assemble the Rail & Install the TrolleyInstall the Idler Pulley Fasten the Rail to the Motor UnitInstall the Chain/Cable Installation Readand Followall Installationwarnings and InstructionsTighten Chain Installation Step Determine the Header Bracket LocationInstall the Header Bracket Wall Header Bracket InstallationCeiling Header Bracket Installation Attach the Rail to the Header Bracket Position the Opener Sectional Door or ONE-PIECE Door with TrackHang the Opener Finished CeilingInstall the Door Control Until the sensor beam is connected and properly alignedInstall the Light Attach the Emergency Release Rope and HandleElectrical Requirements Install The Protector System Important Information about the Safety Reversing SensorWall installation Installing the BracketsGarage door track installation preferred Floor installation FigureAligning the Safety Reversing Sensors Troubleshooting the Safety Reversing SensorsSensors Fasten the Door Bracket StepSectional Doors ONE-PIECEDOORS Connect Door Arm to Trolley Sectional Doors onlyAssemble the door arm, Figure Adjustment procedures, FigureALL ONE-PIECE Doors Connect the door arm to the trolleyIf door does not open at least 5 feet 1.5 m Adjustment StepAdjust the UP and Down Travel Limits If the door does not close completelyAdjust the Force HOW and When to Adjust the ForcesTest the Down close force Important Safety Check Test the Safety Reversal SystemAdjust Test The Protector SystemReadand Followall Warningsand Instructions Using Your Garage Door OpenerOperation No Oneshouldgoundera STOPPED,PARTIALLY OpeneddoorDisconnect the Trolley Using the Wall.Mounted DoorControl To Open the Door Manually To RE-CONNECT the TrolleyAdjustments Remote Control BatteryCare of Your Garage Door Opener Having a PROBLEM? Refer to Adjustment , Adjust the ForceSymptom LED is not fit on door control Symptom Motor unit doesnt operateProgramming To Add or Reprogram a Hand.held Remote ControlUsing the Learn Button To Erase All Codes From Motor Unit MemoryTo Add, Reprogram or Change a Keyless Entry PIN To change an existing, known PINTo set a temporary PIN Installation Parts Repair PartsRail Assembly Parts KEY Part DescriptionMotor Unit Assembly Parts KEY Part NO. noKEY Part Description Accessories Warranty

139.53930D specifications

The Sears 139.53930D is a sophisticated and reliable garage door opener that has made a significant mark in the world of home automation. With its innovative design and advanced features, this model stands out in the crowded marketplace of garage door systems.

One of the defining characteristics of the 139.53930D is its powerful motor. The opener is equipped with a robust 1/2 horsepower motor, providing ample lifting power for a variety of garage door sizes and weights. This ensures smooth and efficient operation, allowing homeowners to go about their daily routines without the worry of a sluggish or malfunctioning door.

Another key feature of the 139.53930D is its safety and security enhancements. The unit comes with a complete set of safety sensors that can detect objects in the door's path, stopping the door from closing if an obstruction is detected. This ensures added safety for children and pets, an essential consideration for any family. Additionally, the model incorporates a rolling code technology that generates a new access code every time the remote is used. This significantly reduces the risk of unauthorized access, giving homeowners peace of mind.

The installation process has also been made simpler with this model's user-friendly design. The package includes detailed instructions and all necessary hardware, making it accessible for both professional installers and DIY enthusiasts. The opener is compatible with various garage door sizes, accommodating most standard installations, which boosts its versatility.

Moreover, the Sears 139.53930D supports multiple forms of remote access. It comes with two streamlined remotes that make it easy to open and close the garage from a distance. For added convenience, the system is compatible with Smart Home technology, allowing users to control the door via smartphone apps or smart home systems. This level of integration is becoming increasingly popular, providing an additional layer of convenience for modern households.

In conclusion, the Sears 139.53930D delivers a robust and secure solution for garage door automation. With its powerful motor, advanced safety features, easy installation, and compatibility with smart technology, it represents a formidable choice for homeowners looking to enhance their garage door system. As the trend towards home automation continues to grow, this model stands out as a reliable and efficient option.
Top Page Image Contents