Sears 139.53930D owner manual Having a PROBLEM?, Refer to Adjustment , Adjust the Force

Page 33

HAVING A PROBLEM?

1.My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction.

•Verify the safety sensors are properly installed, aligned and free of any obstructions. Refer to Installation Step 10: Install The Protector Syster_.

•Check diagnostic LED for flashes on the motor unit then refer to the Diagnostic Chart on the following page.

2.My remotes will not activate the door:

•Reprogram remotes following the programming instructions. Refer to Programming.

•If remote will still not activate your door, check diagnostic LED for flashes on motor unit then refer to Diagnostic Chart on the following page.

3.My door reverses for no apparent reason: Repeat safety reverse test after adjustments to force or travel limits. The need for occasional adjustment for the force and limit settings is normal. Weather conditions in particular can affect door travel.

•Manually check door for balance or any binding problems.

•Refer to Adjustment Step 2, Adjust the Force.

4.My door reverses for no apparent reason after fully closing and touching the floor: Repeat safety reverse test after adjustments to force or travel limits. The need for occasional adjustment for the force and limit settings is normal. Weather conditions in particular can affect door travel.

•Refer to Adjustment Step 1, Adjust the UP and DOWN Travel Limits. Decrease down travel by turning down limit adjustment screw clockwise.

5.My lights will not turn off when door is open:

•The garage door opener is equipped with a security light feature. This feature activates the light on when the safety sensor beam has been obstructed.

Bell Wire

Safety

Reversing Sensor

 

 

Sending

Eye Safety Reversing

Receiving Eye

Safety Reversing

Sensor (Green

Indicator Light)

Sensor

(Amber Indicator Light)

 

 

 

 

,/

 

6.My motor unit hums briefly:

•First verify that the trolley is against the stop bolt.

•Release the door from the opener by pulling the Emergency Release Rope.

•Manually bring the door to a closed position.

•Loosen the chain by adjusting the outer nut 4 to 5 turns. This relieves the tension.

•Run the motor unit from the remote control or door control. The trolley should travel towards the door and stop. If the trolley re-engages with the door, pull the Emergency Release Rope to disengage.

•Decrease the UP travel by turning the UP Travel adjustment screw 2 full turns away from the arrow.

•Re-tighten the outer nut so the chain is a 1/4" (6 mm) above the base of the rail. (When the door is reconnected and closed, the chain will sag. This is normal.)

•If the trolley does not move away from the bolt, repeat the steps above.

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents 315N= Garage Door Opener Abridor DE Puerta DE Cochera 315.= Introduction ContentsPreparing your garage door Tools neededSectional Door Installation Sectional Door InstallationsPlanning ONE-PIECE Door Installations ONE-PIECE Door Without TrackONE-PIECE Door with Track Secu RITY,I Carton InventoryAssembly Hardware Installation HardwareHardware Inventory Assemble the Rail & Install the Trolley Assembly StepFasten the Rail to the Motor Unit Install the Idler PulleyInstall the Chain/Cable Installation Readand Followall Installationwarnings and InstructionsTighten Chain Determine the Header Bracket Location Installation StepInstall the Header Bracket Wall Header Bracket InstallationCeiling Header Bracket Installation Attach the Rail to the Header Bracket Sectional Door or ONE-PIECE Door with Track Position the OpenerFinished Ceiling Hang the OpenerUntil the sensor beam is connected and properly aligned Install the Door ControlAttach the Emergency Release Rope and Handle Install the LightElectrical Requirements Important Information about the Safety Reversing Sensor Install The Protector SystemGarage door track installation preferred Installing the BracketsWall installation Floor installation FigureAligning the Safety Reversing Sensors Troubleshooting the Safety Reversing SensorsSensors Fasten the Door Bracket StepSectional Doors ONE-PIECEDOORS Sectional Doors only Connect Door Arm to TrolleyALL ONE-PIECE Doors Adjustment procedures, FigureAssemble the door arm, Figure Connect the door arm to the trolleyAdjust the UP and Down Travel Limits Adjustment StepIf door does not open at least 5 feet 1.5 m If the door does not close completelyAdjust the Force HOW and When to Adjust the ForcesTest the Down close force Adjust Test the Safety Reversal SystemImportant Safety Check Test The Protector SystemOperation Using Your Garage Door OpenerReadand Followall Warningsand Instructions No Oneshouldgoundera STOPPED,PARTIALLY OpeneddoorControl To Open the Door Manually Using the Wall.Mounted DoorDisconnect the Trolley To RE-CONNECT the TrolleyAdjustments Remote Control BatteryCare of Your Garage Door Opener Refer to Adjustment , Adjust the Force Having a PROBLEM?Symptom Motor unit doesnt operate Symptom LED is not fit on door controlUsing the Learn Button To Add or Reprogram a Hand.held Remote ControlProgramming To Erase All Codes From Motor Unit MemoryTo Add, Reprogram or Change a Keyless Entry PIN To change an existing, known PINTo set a temporary PIN Rail Assembly Parts Repair PartsInstallation Parts KEY Part DescriptionMotor Unit Assembly Parts KEY Part NO. noKEY Part Description Warranty Accessories

139.53930D specifications

The Sears 139.53930D is a sophisticated and reliable garage door opener that has made a significant mark in the world of home automation. With its innovative design and advanced features, this model stands out in the crowded marketplace of garage door systems.

One of the defining characteristics of the 139.53930D is its powerful motor. The opener is equipped with a robust 1/2 horsepower motor, providing ample lifting power for a variety of garage door sizes and weights. This ensures smooth and efficient operation, allowing homeowners to go about their daily routines without the worry of a sluggish or malfunctioning door.

Another key feature of the 139.53930D is its safety and security enhancements. The unit comes with a complete set of safety sensors that can detect objects in the door's path, stopping the door from closing if an obstruction is detected. This ensures added safety for children and pets, an essential consideration for any family. Additionally, the model incorporates a rolling code technology that generates a new access code every time the remote is used. This significantly reduces the risk of unauthorized access, giving homeowners peace of mind.

The installation process has also been made simpler with this model's user-friendly design. The package includes detailed instructions and all necessary hardware, making it accessible for both professional installers and DIY enthusiasts. The opener is compatible with various garage door sizes, accommodating most standard installations, which boosts its versatility.

Moreover, the Sears 139.53930D supports multiple forms of remote access. It comes with two streamlined remotes that make it easy to open and close the garage from a distance. For added convenience, the system is compatible with Smart Home technology, allowing users to control the door via smartphone apps or smart home systems. This level of integration is becoming increasingly popular, providing an additional layer of convenience for modern households.

In conclusion, the Sears 139.53930D delivers a robust and secure solution for garage door automation. With its powerful motor, advanced safety features, easy installation, and compatibility with smart technology, it represents a formidable choice for homeowners looking to enhance their garage door system. As the trend towards home automation continues to grow, this model stands out as a reliable and efficient option.
Top Page Image Contents