Sears 139.53930D owner manual Fasten the Door Bracket, Step, Sectional Doors

Page 23

INSTALLATION STEP 1 1

Fasten the Door Bracket

Follow instructions which apply to your door type as illustrated below or on the following page.

A horizontal reinforcement brace should be long enough to be secured to two vertical supports. A vertical reinforcement brace should cover the height of the top panel.

The illustration shows one piece of angle iron as the horizontal brace. For the vertical brace, two pieces of angle iron are used to create a U-shaped support (Figure 1). The best solution is to check with your garage

door manufacturer for an opener installation door reinforcement kit.

NOTE: Many vertical brace installations provide for direct attachment of the clevis pin and door arm. In this case you will not need the door bracke# proceed to Installation

Step 12.

SECTIONAL DOORS

Fiberglass,aluminum or lightweight steel garage doors WILL REQUIREreinforcement BEFOREinstallation of door bracket.

Contactyour door manufacturerfor reinforcement kit.

HARDWARE SHOWN ACTUAL SIZE

© ©

Nut 5/16"-18

LockWasher

5/16"

Carriage Bolt 5/16"-18x2-1/2"

•Center the door bracket on the previously marked vertical centerline used for the header bracket

installation. Note correct UP placement, as stamped inside the bracket (Figure 2).

•Position the bracket on the face of the door within the following limits:

A)The top edge of the bracket 2"-4" (5-10 cm) below the top edge of the door.

B)The top edge of the bracket directly below any structural support across the top of the door.

•Mark and drill 5/16" left and right fastening holes.

Secure the bracket as shown in Figure 1 if there is vertical reinforcement.

If your installation doesn't require vertical reinforcement but does need top and bottom fastening holes for the door bracket, fasten as shown in Figure 2.

Header Bracket

Horizontal and vertical reinforcement

is needed for lightweight garage doors (fiberglass, aluminum, steel, doors with glass panel, etc.). (Not Provided)

 

Vertical

 

 

Reinforcement

 

 

 

Vertical

 

 

Centerline

 

 

//of Garage

 

 

,' Door

 

Carriage Bolt

UP

 

 

ge

 

 

of Door or

 

 

 

Door

 

einforcement Board

Bracket

 

 

Lock Washer

-_(

 

5/16"

 

 

Nut

 

 

5/16"-18

z

Figure 1

Door Bracket

Figure 2

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents 315N= Garage Door Opener Abridor DE Puerta DE Cochera 315.= Introduction ContentsPreparing your garage door Tools neededPlanning Sectional Door InstallationSectional Door Installations ONE-PIECE Door with Track ONE-PIECE Door InstallationsONE-PIECE Door Without Track Secu RITY,I Carton InventoryHardware Inventory Assembly HardwareInstallation Hardware Assemble the Rail & Install the Trolley Assembly StepFasten the Rail to the Motor Unit Install the Idler PulleyInstall the Chain/Cable Tighten Chain InstallationReadand Followall Installationwarnings and Instructions Determine the Header Bracket Location Installation StepCeiling Header Bracket Installation Install the Header BracketWall Header Bracket Installation Attach the Rail to the Header Bracket Sectional Door or ONE-PIECE Door with Track Position the OpenerFinished Ceiling Hang the OpenerUntil the sensor beam is connected and properly aligned Install the Door ControlAttach the Emergency Release Rope and Handle Install the LightElectrical Requirements Important Information about the Safety Reversing Sensor Install The Protector SystemFloor installation Figure Installing the BracketsGarage door track installation preferred Wall installationSensors Aligning the Safety Reversing SensorsTroubleshooting the Safety Reversing Sensors Sectional Doors Fasten the Door BracketStep ONE-PIECEDOORS Sectional Doors only Connect Door Arm to TrolleyConnect the door arm to the trolley Adjustment procedures, FigureALL ONE-PIECE Doors Assemble the door arm, FigureIf the door does not close completely Adjustment StepAdjust the UP and Down Travel Limits If door does not open at least 5 feet 1.5 mTest the Down close force Adjust the ForceHOW and When to Adjust the Forces Test The Protector System Test the Safety Reversal SystemAdjust Important Safety CheckNo Oneshouldgoundera STOPPED,PARTIALLY Openeddoor Using Your Garage Door OpenerOperation Readand Followall Warningsand InstructionsTo RE-CONNECT the Trolley Using the Wall.Mounted DoorControl To Open the Door Manually Disconnect the TrolleyCare of Your Garage Door Opener AdjustmentsRemote Control Battery Refer to Adjustment , Adjust the Force Having a PROBLEM?Symptom Motor unit doesnt operate Symptom LED is not fit on door controlTo Erase All Codes From Motor Unit Memory To Add or Reprogram a Hand.held Remote ControlUsing the Learn Button ProgrammingTo set a temporary PIN To Add, Reprogram or Change a Keyless Entry PINTo change an existing, known PIN KEY Part Description Repair PartsRail Assembly Parts Installation PartsKEY Part Description Motor Unit Assembly PartsKEY Part NO. no Warranty Accessories

139.53930D specifications

The Sears 139.53930D is a sophisticated and reliable garage door opener that has made a significant mark in the world of home automation. With its innovative design and advanced features, this model stands out in the crowded marketplace of garage door systems.

One of the defining characteristics of the 139.53930D is its powerful motor. The opener is equipped with a robust 1/2 horsepower motor, providing ample lifting power for a variety of garage door sizes and weights. This ensures smooth and efficient operation, allowing homeowners to go about their daily routines without the worry of a sluggish or malfunctioning door.

Another key feature of the 139.53930D is its safety and security enhancements. The unit comes with a complete set of safety sensors that can detect objects in the door's path, stopping the door from closing if an obstruction is detected. This ensures added safety for children and pets, an essential consideration for any family. Additionally, the model incorporates a rolling code technology that generates a new access code every time the remote is used. This significantly reduces the risk of unauthorized access, giving homeowners peace of mind.

The installation process has also been made simpler with this model's user-friendly design. The package includes detailed instructions and all necessary hardware, making it accessible for both professional installers and DIY enthusiasts. The opener is compatible with various garage door sizes, accommodating most standard installations, which boosts its versatility.

Moreover, the Sears 139.53930D supports multiple forms of remote access. It comes with two streamlined remotes that make it easy to open and close the garage from a distance. For added convenience, the system is compatible with Smart Home technology, allowing users to control the door via smartphone apps or smart home systems. This level of integration is becoming increasingly popular, providing an additional layer of convenience for modern households.

In conclusion, the Sears 139.53930D delivers a robust and secure solution for garage door automation. With its powerful motor, advanced safety features, easy installation, and compatibility with smart technology, it represents a formidable choice for homeowners looking to enhance their garage door system. As the trend towards home automation continues to grow, this model stands out as a reliable and efficient option.
Top Page Image Contents