State Industries SGV 120 10TS, 198067-000, SGV 82 10TS Wiring of Element, Thermostat

Page 5

3.Fill the tank until water runs out an opened hot water faucet. This will let out air in the tank and the piping. Close the faucet after the water comes out. You must not turn the electricity on until the tank is full of water. IF ANY AIR IS LEFT IN THE TOP OF THE TANK, THE TOP HEATING ELEMENT WILL BURN OUT RIGHT AWAY.

4.Check all the new water piping for leaks. Fix as needed.

WIRING OF ELEMENT

Determine voltage and wattage from the rating plate attached to the tank. All external wiring, connection, and overcurrent protective devices must be provided and installed in accordance with the latest edition of the National Electrical Code, local codes, and local utility requirements. The tank must be electrically “grounded” by the installer. A green ground screw has been provided on the tank’s junction box.

The grounding electrode conductor shall be of copper, aluminum, or copperclad aluminum. The material shall be resistant to corrosion, and shall be of one continuous length without a splice or joint.

Rigid metal conduit, intermediate metal conduit, or electrical metallic tubing may be used for the grounding means if conduit or tubing is terminated in fittings approved for grounding.

FIGURE 5

Flexible metal conduit or flexible metallic tubing shall be permitted for grounding if all the following conditions are met:

1.The length in any ground return path does not exceed 6 feet.

2.The circuit conductors contained therein are protected by overcurrent devices rated at 20 amperes or less.

3.The conduit or tubing is terminated in fittings approved for grounding.

WARNING

Never use this tank unless it is completely full of water.

WARNING

TANKS EQUIPPED FOR ONE TYPE VOLTAGE ONLY. This tank is equipped for one type of voltage only. Check the rating plate near the bottom access panel for the correct voltage. DO NOT USE THIS TANK WITH ANY VOLTAGE OTHER THAN THE ONE SHOWN ON THE MODEL RATING PLATE. Failure to use the correct voltage can cause problems which can result in DEATH, SERIOUS BODILY INJURY OR PROPERTY DAMAGE. If you have any questions or doubts consult your electric company.

CAUTION

If wiring from the fuse box or circuit breaker box was aluminum for the old tank, replace it with copper wire. If you wish to reuse the existing aluminum wire, have the connection at the tank made by a competent electrician. Contact your local utility to arrange for a professional electrician.

FIGURE 6

THERMOSTAT

Each thermostat is factory preset at 120°F to reduce the risk of scald injury. This setting has proven by experience to be most satisfactory from the standpoint of operational costs and household needs.

Tanks installed in Florida require the thermostat(s) to be set at 125°F. If you wish to adjust the settings, see the “Temperature Adjustment” section of this installation manual.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Rating Plate Geothermal Storage TanksTypical Installation Table of ContentsTEMPERATURE-PRESSURE Relief Valve InstallationLocal Codes Locating the Geothermal Storage TankFilling the Geothermal Storage Tank with Water Water PipingThermostat Wiring of ElementTemperature Settings Temperature RegulationTemperature Adjustment OperationElement Replacement MaintenanceDraining ElementWater Heater Sounds Repair PartsOrdering Repair Parts

198067-000, SGV 120 10TS, SGV 82 10TS specifications

State Industries has a rich history in the manufacturing of high-quality water heaters and heating equipment, and two of its notable products, the State Industries 198067-000, SGV 82 10TS, and SGV 120 10TS, exemplify the company's commitment to innovation and efficiency.

The State Industries 198067-000 is an exemplary water heater designed for both residential and light commercial applications. It features a powerful heating element that ensures a quick recovery rate, providing users with an ample supply of hot water. With a capacity designed to meet various demands, this model stands out for its efficient performance and durability. The use of high-quality materials in its construction helps in maintaining a longer lifespan while minimizing the risk of leaks or failures.

The SGV 82 10TS model is particularly engineered for industrial applications, featuring a robust design that meets the rigorous demands of commercial users. One of its most remarkable features is its high thermal efficiency, which significantly reduces energy consumption while ensuring a steady supply of hot water. This model is equipped with advanced insulation to minimize heat loss, thus enhancing its overall operational efficiency.

In terms of technology, the SGV 120 10TS incorporates an advanced control system that allows for precise management of water heating cycles. This not only improves energy savings but also maximizes the system's performance according to real-time demands. The incorporation of advanced sensors provides seamless monitoring of temperature and pressure, ensuring optimal safety and efficiency in operation.

Both models are designed with user-friendliness in mind, boasting easy installation and maintenance features. An accessible design means that routine checks and servicing can be performed without significant effort, leading to prolonged equipment life and reduced downtime. Furthermore, these water heaters are compliant with various industry standards, ensuring that they meet safety and performance regulations.

Overall, the State Industries 198067-000, SGV 82 10TS, and SGV 120 10TS embody cutting-edge technology and reliable performance, making them top choices for users seeking efficiency, durability, and ease of use in their water heating needs.
Top Page Image Contents