Multiquip QP4TE manual Engine Safety

Page 8

CAUTION

„NEVER lubricate components or attempt service on a running machine.

„NEVER block or restrict flow from discharge hose. Remove kinks from discharge line before starting pump. Operation with a blocked discharge line can cause water inside pump to overheat.

NOTICE

„ALWAYS fill the pump casing with water before starting the engine. Failure to maintain water inside the pump housing will cause severe damage to the pump and mechanical seal.

„In winter drain water from pump housing to prevent freezing.

„NEVER start the pump with the clean-out cover removed. The rotating impeller inside the pump can cut or sever objects caught in it. Before starting the pump, check that the clean-out cover is securely fastened.

„ALWAYS keep the machine in proper running condition.

„ALWAYS ensure pump is on level ground before use.

„Fix damage to machine and replace any broken parts immediately.

„ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel.

SAFETY INFORMATION

ENGINE SAFETY

WARNING

„NEVER operate the engine with heat shields or guards removed.

„ DO NOT remove the engine oil drain plug while the engine is hot. Hot oil will gush out of the oil tank and severely scald any persons in the general area of the pump.

CAUTION

„NEVER touch the hot exhaust manifold, muffler or cylinder. Allow these parts to cool

before servicing equipment.

NOTICE

„NEVER run engine without an air filter or with a dirty air filter. Severe engine damage may occur. Service air filter frequently to prevent engine malfunction.

„NEVER tamper with the factory settings of the engine or engine governor. Damage to the engine or equipment can result

if operating in speed ranges above the maximum allowable.

PAGE 8 —OPERATION AND PARTS MANUAL — REV. #1 (10/10/08)

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Model QP4TE Proposition 65 Warning Operation & Parts Manual REV. #0 01/25/06 Table of Contents Parts Ordering Procedures Ordering parts has never been easierSafety Information Safety MessagesGeneral Safety Engine Safety Fuel Safety Transporting Safety Operation and Parts Manual REV. #1 10/10/08 General Information ApplicationSpecifications Pump Specifications Engine Specifications EnginePump Components Used in general de-watering applications. TypicalBasic Engine Initial ServicingPRE-INSPECTION Engine InspectionPRE-SETUP Pump Before StartingInitial START-UP Engine Initial START-UP Engine Normal ShutdownMaintenance Pump Pump Vacuum TestPressure reading may vary Maintenance Engine Engine Maintenance Schedule24 -OPERATION and Parts Manual REV. #1 10/10/08 Preparation for Long -TERM Storage Pump StorageTroubleshooting Engine Troubleshooting ENGINE/PUMP Explanation of Code in Remarks Column Suggested Spare Parts QP4TE 1 to 5 Units withPump Assy Pump Assy 32 -OPERATION and Parts Manual REV. #1 10/10/08 Part Name QTY Remarks Robin EX270D50220 Engine AIR Cleaner Assy Base CP Robin EX270D50220 Engine Camshaft Assy PIN, CAMSHAFT, 9DX78.5L Robin EX270D50220 Engine Carburetor Assy Valve Throttle Robin EX270D50220 Engine Crankcase Assy Robin EX270D50220 Engine Crankcase Assy Robin EX270D50220 Engine CRANKSHAFT/PISTON Assy Crankshaft CP Robin EX270D50220 Engine Cylinder Head Assy Collet Valve Robin EX270D50220 Engine Fueltank Assy Part Name Robin EX270D50220 Engine Governor Assy Governor Lever Robin EX270D50220 Engine Ignition COIL/FLYWHEEL Assy Robin EX270D50220 Engine Ignition COIL/FLYWHEEL Assy Robin EX270D50220 Engine Muffler Assy Muffler CP Robin EX270D50220 Engine OIL Sensor Assy OIL Sensor CP Robin EX270D50220 Engine Recoil Starter Assy LABEL, Trade Mark 64D Terms and Conditions of Sale Parts Operation and Parts Manual REV. #1 10/10/08 HERE’S HOW to GET Help
Top Page Image Contents