Fluke fluke123 user manual About this Chapter, Cleaning the Test Tool, Storing the Test Tool

Page 44

About this Chapter

This chapter covers basic maintenance procedures that can be performed by the user. For complete service, disassembly, repair, and calibration information, see the Service Manual. You will find the part number of the Service Manual in the section ‘Parts and Accessories’ in this manual.

Chapter 2

Maintaining the Test Tool

Cleaning the Test Tool

Clean the test tool with a damp cloth and a mild soap to avoid abrasion of text on the test tool. Do not use abrasives, solvents, or alcohol.

Storing the Test Tool

If you are storing the test tool for an extended period of time, charge the Ni-Cd battery pack before storing. It is not necessary to remove the battery pack.

37

Image 44

Contents Fluke Limited Warranty & Limitation of Liability Service Centers Table of Contents Fluke Iii Specifications Declaration of Conformity ManufacturerStatement of Conformity Sample testsUnpacking the Test Tool Kit # DescriptionModel 123 123/SCCScopeMeter Test Tool Kit Safely Using the Test Tool Safely Using the Test Tool Fluke Powering the Test Tool Goal of this ChapterResetting the Test Tool Screen After ResetChanging Backlight Reading the Screen From full to emptyMaking Selections in a Menu Basic NavigationInput B Looking at the Measurement ConnectionsInput a Displaying an Unknown Signal with Connect-and View Screen After an Auto SetMeasurement Setup Making MeasurementsHz and Vpp as Main Readings Touch Hold OFF appears on Freezing the ScreenHolding a Stable Reading Making Relative Measurements Making a Relative MeasurementSelecting Auto/Manual Ranges Changing the Graphic Representation on the ScreenChanging the Time Base Changing the AmplitudeOn the screen Positioning the Waveform on the ScreenObserve that the trigger identifier moves horizontally Smoothing the Waveform 11. Smoothing the WaveformDisplaying the Envelope of a Waveform 12. Displaying the Envelope of a WaveformTrendPlotting a Waveform Starting a TrendPlot functionAcquiring the Waveform Changing the TrendPlot ReadingTurning Off the TrendPlot Display Making a Single Acquisition14. Making a Single Acquisition Recording Slow Signals over a Long Period of Time Start RecordingSelecting AC-Coupling Reversing the Polarity of the Displayed WaveformSetting Trigger Level and Slope Triggering on a Waveform     Selecting the Trigger ParametersIsolated Triggering Triggering on Video Signals 17. Isolated Triggering18. Measuring Video Signals Triggering on a Specific Video Line Recalling Screens Saving and Recalling a Setup or a ScreenSaving Screens Deleting Screens Using a Printer 19. Connecting a Serial Printer    Using FlukeView Software 21. Connecting a ComputerStoring the Test Tool Cleaning the Test ToolAbout this Chapter Charging the Ni-Cd Battery Pack Charging the Battery PackKeeping Batteries in Optimal Condition Replacing and Disposing of the Ni-Cd Battery Pack Replacing the Battery PackUsing and Adjusting 101 Scope Probes Adjusting Scope Probes  Calibrating the Test Tool Parts and AccessoriesStandard Accessories Standard Accessories Ordering CodeMaintaining the Test Tool Parts and Accessories Optional Accessories SW90WUsing the Tilt Stand Using the Tilt StandChanging the Information Language Setting the Grid Display Adjusting the Screen Contrast Changing the DisplayChanging Date and Time Saving Battery Life Setting the Power Down TimerChanging the Auto Set Options Using Proper Grounding PotentialFluke multimeter Solving Printing and Other Communication ErrorsBattery Testing of Fluke Accessories Performance Characteristics Safety CharacteristicsIntroduction Environmental DataDual Input Oscilloscope VerticalHorizontal TriggerRanges Sampling Rate for both channels simultaneouslyAuto Set Advanced Scope FunctionsDisplay Modes Dual Input Meter Input a and Input BPhase Duty Cycle DutyPulse Width Pulse Decibel dBAdvanced Meter Functions Power MiscellaneousDisplay MemoryEnvironmental Electromagnetic Compatibility EMCUp to 400 Hz SafetyMax. Input Voltage Input a and B Trace disturbance with STL120 No visible disturbance = 3 V/m= 10 V/m Disturbance less than 10% of full scaleVDC, VAC, VAC+DC OHM, CONT, Diode CAP Index Fluke Index Fluke