Pella 81470102 installation instructions Cable clamps Jamb covers

Pella 81470102 installation instructions Cable clamps Jamb covers Pella 81470102 1ROUGH Opening Preparation, Remember to USE Appropriate Personal Protective Equipment Pella 81470102 installation instructions Siding Pella 81470102 installation instructions 2PREPARING and Setting the Window Pella 81470102 3CABLE Clamp Installation, TWO or More People will be Required for the Following Steps Pella 81470102 Cross Bracing Mount of Cable Clamps, Cross Bracing Mount NON Accessible Cable Attachment Pella 81470102 Supporting the Window, Header Mount of Cable Clamps, Remove blocking from under the seat board Pella 81470102 installation instructions 5INSULATING Foam Application, Apply insulating foam sealant. From the interior Pella 81470102 installation instructions Angle Jamb Cover, Vinyl Siding Replacement Wood Siding Replacement Pella 81470102 6SEALING the Window to the Exterior Wall Cladding, If using Square Jamb Cover, Proceed to C Pella 81470102 installation instructions 7INSTALLING Interior Jamb Cove Mould Pella 81470102 installation instructions Interior Finishing, Exterior Finish, Care and Maintenance Important Notice
Page 1

© 2009 Pella CorporationPart Number: 81470102

INSTALLATION INSTRUCTION - INSTRUCCIONES DE INSTALACIÓN FOR SQUARE DESIGN BAY AND BOW WINDOW WITH SEAT BOARD

Lea las instrucciones en español en el reverso.

Read these instructions thoroughly before performing any steps.

Cable clamps

Jamb covers

(2-1/2" Wide)

Head frame

expander

Flashing tape #1

Flashing tape #2

Knee braces

Always read the Pella® Limited Warranty before purchasing or installing Pella products. By installing this product, you are acknowledging that this Limited Warranty is part of the terms of the sale. Failure to comply with all Pella installation and maintenance instructions may void your Pella product warranty. See Limited Warranty for complete details at http://warranty.pella.com.

Note: These instructions may be used for Square Design Pella Bay and Bow windows that have a head and seat board. Support cables are installed in factory assembled bay and bow combinations.

Caution: The factory-installed support cables must be attached to members capable of supporting 1,300 lbs. If the members are not capable of supporting 1,300 lbs., knee braces must be used in addition to the cables. Bay and bow units are not intended to support any roof structure. Consult an architect, engineer or construction professional if the ability of the members to support the bay or bow is not known.

Installation Instructions for Typical Wood Frame Construction.

These instructions were developed and tested for use with typical wood frame wall construction in a wall system designed to manage water. These instructions are not to be used with any other construction method. Installation instructions for use with other construction methods, multiple units or other bow and bay windows, may be obtained from Pella Corporation, a local Pella retailer, or by visiting http://www.pella.com. Building designs, construction methods, building materials, and site conditions unique to your project may require an installation method different from these instructions and additional care. Determining the appropriate installation method is the responsibility of you, your architect, or construction professional.

Page 1 Page 2
Image 1
Page 1 Page 2
Contents Cable clamps Jamb covers 1ROUGH Opening Preparation Replacement Applications RemoveRemember to USE Appropriate Personal Protective Equipment Remove all packaging from the windowSiding 2PREPARING and Setting the Window TWO or More People will be Required for the Following Steps 3CABLE Clamp InstallationInstall 2 x 6 cross braces between the rafter Cross Bracing Mount NON Accessible Cable AttachmentCross Bracing Mount of Cable Clamps Run the cable up through the bottom of the cable clampHeader Mount of Cable Clamps Supporting the WindowRemove blocking from under the seat board Run the cable up through the bottomApply insulating foam sealant. From the interior 5INSULATING Foam ApplicationAngle Jamb Cover Vinyl Siding Replacement Wood Siding ReplacementIf using Angle Jamb Cover, Proceed to G If using Square Jamb Cover, Proceed to C6SEALING the Window to the Exterior Wall Cladding Cove Mould 7INSTALLING Interior Jamb Cove MouldInterior Finishing Care and Maintenance Important NoticeExterior Finish
Top Page Image Contents