Is the recommended installation set up

Installation

10.The pipe must extend at least 12” (30 cm) away from the building. If necessary, bring another length of pipe (PL type) to the outside of the home to connect to the first section. Do not forget to place high temperature silicone around the pipe that passes through the thimble.

11.Install a vertical pipe, or if all requirements for direct venting are met, install vent termination. The stainless steel cap termination manufactured by the vent manufacturer is recommended. However, when the vent terminates several feet above ground level and there are no trees, plants, etc. within several feet, a 45° elbow can be used as termination. The elbow must be turned down to prevent

rain from entering.

NOTE:

•Some horizontal through wall installations may require a “T” and 3 to 5 feet (91 to 152 cm) of vertical pipe outside the building to help naturally draft in the unit.

•This may be required if a proper burn cannot be maintained, after the stove has been tested and the airflow set.

•This is due to the back pressure in the exhaust caused by airflow around the structure.

•All sections of pipe must have three (3) screws evenly spaced and all horizontal and vertical vent sections located within the house must have a bead of high temperature silicone installed on the male end of the pipe before installation to create a gas tight seal.

THROUGH WALL WITH VERTICAL RISE AND HORIZONTAL TERMINATION INSTALLATION - FREESTANDING:

A 45° elbow with a rodent screen may be used in place of the termination cap (or stainless steel termination hood).

Figure 24 is the recommended installation set up.

Figure 25 is the installation to use if there is a concrete or retaining wall in line with exhaust vent on a pellet stove. The termination must be 12” (30 cm) from the outside wall and 12” (30 cm) above the ground.

Termination cap
90° elbow
Wall framing
Vertical section
of vent pipe	Wall strap
Horizontal frame
for thimble
	Clean out tee
	Wall thimble
ENVIRO EF3

Figure 24: Venting horizontally with rise.

Horizontal frame
for thimble	Termination cap
Wall thimble
90° elbow
Wall framing
Vertical section
of vent pipe
	Concrete Wall
ENVIRO EF3	Clean out tee

Figure 25: Venting with concrete wall behind unit .

EF3 specifications

The Enviro EF3 is an innovative and eco-friendly vehicle that is transforming the landscape of sustainable transportation. With a focus on efficiency, performance, and environmental responsibility, the EF3 represents a significant leap forward in automotive technology.

One of the standout features of the Enviro EF3 is its advanced electric powertrain. This vehicle is equipped with a state-of-the-art electric motor that provides impressive torque and acceleration while remaining silent and efficient. The electric motor is powered by a high-capacity lithium-ion battery pack, which can be charged quickly and has a long lifespan. This allows for extended driving ranges, making the EF3 ideal for both urban commuting and longer journeys.

The EF3 also incorporates regenerative braking technology, which captures energy that would otherwise be lost during braking. This innovative feature helps to recharge the battery while enhancing overall energy efficiency. As a result, drivers can enjoy longer trips and reduced charging frequency, while also minimizing the vehicle's overall environmental impact.

In terms of design, the Enviro EF3 boasts a sleek, aerodynamic profile that not only looks modern but also contributes to its overall efficiency. The vehicle's exterior is crafted using lightweight materials, which enhance performance and help to maximize range. Additionally, the spacious interior is designed with comfort and sustainability in mind. Eco-friendly materials are used throughout the cabin, ensuring that the EF3 remains a green choice even inside the vehicle.

Connectivity is another vital characteristic of the Enviro EF3. Equipped with the latest infotainment and navigation technologies, the vehicle offers seamless integration with smartphones and other devices. This feature allows drivers to access real-time traffic updates, manage charging schedules, and even control various vehicle settings from their mobile devices.

Safety is prioritized in the design of the EF3, with advanced driver-assistance systems (ADAS) that include features such as adaptive cruise control, lane-keeping assist, and collision avoidance technology. These systems work together to enhance driver confidence and ensure a safe driving experience.

In conclusion, the Enviro EF3 represents the future of sustainable transportation. With its electric powertrain, advanced technologies, aerodynamic design, and a strong focus on safety and connectivity, the EF3 is a versatile and eco-friendly vehicle that meets the demands of modern drivers while contributing to a healthier planet. As more consumers seek environmentally responsible choices, the Enviro EF3 stands out as a leading option in the electric vehicle market.