Operating Instructions, Special Notes | Enviro EF3 instruction

Operating Instructions

AUTOMATIC SAFETY FEATURES:

Your pellet Stove has the following safety features:

A. The stove will shut off when the fire goes out and the exhaust temperature drops below 120°F (49°C).

B. The stove has a high temperature safety switch. If the temperature on the hopper reaches 200°F (93°C), the auger will automatically stop and the stove will shut down when the exhaust temperature cools. If this happens, call your local dealer to reset the 200°F (93°C) high limit switch. ALSO FIND

THE REASONS WHY THE UNIT OVERHEATED.

C. The unit has a convection fan control over-ride. This function causes the convection fan to reach its full speed when the temperature at the back of the firebox reaches 160°F (71°C). This is a normal safety feature of your unit. To compensate for the fan cycling action that may occur, turn up the blower control proportionately to the heat output.

D. If the power goes out, the unit will stop running. When the power comes back on, the stove will not restart unless the exhaust temperature is still above 120°F (49 °C).

SLIDER/DAMPER SETTING:

The slider/damper must be set at time of installation. This is used to regulate the airflow through the pellet stove. The slider damper is located behind the left side panel. To open the left side panel, undo

the one screw located in the upper front corner of the cabinet side

SPECIAL NOTES:

The easiest way to make sure that an efficient flame is achieved is to understand the characteristics of the fire.

•A tall, lazy flame with dark orange tips, requires more air – Open slider (pull out) slightly.

•A short, brisk flame, like a blowtorch, has too much air – Close slider (push in) slightly.

•If the flame is in the middle of these two characteristics with a bright yellow/orange,

Figure 1: Efficient Flame. active flame with no black tips then the air is set for proper operation

Pellet quality is a major factor in how the Pellet stove will operate. If the pellets have a high moisture content or ash content the fire will be less efficient and has a higher possibility of the fire building up and creating clinkers (hard ash build-up).

If the fire should happen to go out and the Dial-A-Fire has been set on the lowest setting, the Slider Damper should be pushed in slightly, decreasing the air in the firebox or the Dial-A-Fire and Auger Trim can be turned up slightly.

If, after long periods of burning, the fire builds up and overflows the burn pot or there is a build up of clinkers, this would be a sign that the pellet quality is poor, this requires more primary air, the slider damper must be pulled out to compensate. Pulling the slider damper out gives the fire more air.

��

Figure 2: Slider / damper positions.

EF3 specifications

The Enviro EF3 is an innovative and eco-friendly vehicle that is transforming the landscape of sustainable transportation. With a focus on efficiency, performance, and environmental responsibility, the EF3 represents a significant leap forward in automotive technology.

One of the standout features of the Enviro EF3 is its advanced electric powertrain. This vehicle is equipped with a state-of-the-art electric motor that provides impressive torque and acceleration while remaining silent and efficient. The electric motor is powered by a high-capacity lithium-ion battery pack, which can be charged quickly and has a long lifespan. This allows for extended driving ranges, making the EF3 ideal for both urban commuting and longer journeys.

The EF3 also incorporates regenerative braking technology, which captures energy that would otherwise be lost during braking. This innovative feature helps to recharge the battery while enhancing overall energy efficiency. As a result, drivers can enjoy longer trips and reduced charging frequency, while also minimizing the vehicle's overall environmental impact.

In terms of design, the Enviro EF3 boasts a sleek, aerodynamic profile that not only looks modern but also contributes to its overall efficiency. The vehicle's exterior is crafted using lightweight materials, which enhance performance and help to maximize range. Additionally, the spacious interior is designed with comfort and sustainability in mind. Eco-friendly materials are used throughout the cabin, ensuring that the EF3 remains a green choice even inside the vehicle.

Connectivity is another vital characteristic of the Enviro EF3. Equipped with the latest infotainment and navigation technologies, the vehicle offers seamless integration with smartphones and other devices. This feature allows drivers to access real-time traffic updates, manage charging schedules, and even control various vehicle settings from their mobile devices.

Safety is prioritized in the design of the EF3, with advanced driver-assistance systems (ADAS) that include features such as adaptive cruise control, lane-keeping assist, and collision avoidance technology. These systems work together to enhance driver confidence and ensure a safe driving experience.

In conclusion, the Enviro EF3 represents the future of sustainable transportation. With its electric powertrain, advanced technologies, aerodynamic design, and a strong focus on safety and connectivity, the EF3 is a versatile and eco-friendly vehicle that meets the demands of modern drivers while contributing to a healthier planet. As more consumers seek environmentally responsible choices, the Enviro EF3 stands out as a leading option in the electric vehicle market.