Enviro EF3 owner manual Outside Vertical Installation

Page 21

Installation

 

Rain cap

 

Flashing

 

24"

 

(61cm)

 

3" (7.5cm)

 

Clearance

 

1"

 

(2.5cm)

 

Support

 

bracket

 

Tee with

 

cleanout

6"

Type "L"

(15cm)

vent

 

Fresh air

 

intake

Non-combustible

Existing floor

floor protection.

(combustible)

Figure 27: Outside Vertical Installation.

HEARTH MOUNT INSTALLATION - FREESTANDING:

��������� ���

��������� ������

������ ���� ����

�������� �� �����

������� ������ ������

��������� ��� ��

������������ ����

����������� ��

������� ��� �����

������ �������

�� �������� ����

��� ����� ��� ������

������� �� ��� ���

���� ��� �� �����

 

��� ��

 

���� ���

 

����� ����������

������� ���������

����������� �����

Refer to Figures 28 and 29.

1.Install the hearth pad.

2.Lock fireplace damper in the open position.

3.Install a positive flue connector at the fireplace dampers.

4.Connect a tee or a 90° elbow to the exhaust pipe.

5.Install flexible stainless steel liner or listed pellet vent to the top of the chimney.

Figure 28: Freestanding hearth mount installation.

21

Image 21
Contents EF3 Table of Contents Introduction I. Pellet StandardsStore pellets at least 36 1 m away from the pellet stove USE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel Reasons WHY the Unit Overheated Operating InstructionsSpecial Notes Dial-A-Fire control panel Tools Required to Clean Unit Routine Cleaning and MaintenanceBurn POT and Liner 2-3 days Inside Firebox weeklyFreestanding ASH PAN Removal of the firebox backing for bi-annual cleaningHeat Exchanger Tubes 2-3 days Fresh AIR Intake seasonPost Season CLEAN-UP Cleaning Plated SurfacesBrick Panel Screws to take out to remove stove from pallet InstallationDimensions of EF3 Freestanding Minimum Alcove width Inches 91 cm Minimum Alcove height EF3 Built-In Heater recommended Framing Or from the outside of the pedestal for the FPI or BIHVent surfaces can Install Vent AT Clearances Specified by Venting Manufacturer Fresh Air Intake Place the appliance 15 37.5 cm Is the recommended installation set up Inside Vertical Installation Outside Vertical Installation Freestanding hearth mount installation overview Connect a tee or 90 degree Control panel see Figure Corner brackets for Trim RemovalTube scrapper rod Placement Stove will not operate when hot. Check the hopper for fuel TroubleshootingDo not What to do ifExhaust motor will not function normally Dial-a-fire has no effect on the fire Timer Control Only Auger motor will not function normallyPotentiometer Readings 200F 93C high limit temperature sensor has tripped Stove will not shut offStove keeps going out Timer Control Wiring DiagramReference Description Part Number Parts ListParts List Options Parts Diagram Components EF3 Steel Components Warranty To the DistributorFor the do-it-yourself Individual Name of Owner Address Installation Data Sheet
Related manuals
Manual 43 pages 19.26 Kb

EF3 specifications

The Enviro EF3 is an innovative and eco-friendly vehicle that is transforming the landscape of sustainable transportation. With a focus on efficiency, performance, and environmental responsibility, the EF3 represents a significant leap forward in automotive technology.

One of the standout features of the Enviro EF3 is its advanced electric powertrain. This vehicle is equipped with a state-of-the-art electric motor that provides impressive torque and acceleration while remaining silent and efficient. The electric motor is powered by a high-capacity lithium-ion battery pack, which can be charged quickly and has a long lifespan. This allows for extended driving ranges, making the EF3 ideal for both urban commuting and longer journeys.

The EF3 also incorporates regenerative braking technology, which captures energy that would otherwise be lost during braking. This innovative feature helps to recharge the battery while enhancing overall energy efficiency. As a result, drivers can enjoy longer trips and reduced charging frequency, while also minimizing the vehicle's overall environmental impact.

In terms of design, the Enviro EF3 boasts a sleek, aerodynamic profile that not only looks modern but also contributes to its overall efficiency. The vehicle's exterior is crafted using lightweight materials, which enhance performance and help to maximize range. Additionally, the spacious interior is designed with comfort and sustainability in mind. Eco-friendly materials are used throughout the cabin, ensuring that the EF3 remains a green choice even inside the vehicle.

Connectivity is another vital characteristic of the Enviro EF3. Equipped with the latest infotainment and navigation technologies, the vehicle offers seamless integration with smartphones and other devices. This feature allows drivers to access real-time traffic updates, manage charging schedules, and even control various vehicle settings from their mobile devices.

Safety is prioritized in the design of the EF3, with advanced driver-assistance systems (ADAS) that include features such as adaptive cruise control, lane-keeping assist, and collision avoidance technology. These systems work together to enhance driver confidence and ensure a safe driving experience.

In conclusion, the Enviro EF3 represents the future of sustainable transportation. With its electric powertrain, advanced technologies, aerodynamic design, and a strong focus on safety and connectivity, the EF3 is a versatile and eco-friendly vehicle that meets the demands of modern drivers while contributing to a healthier planet. As more consumers seek environmentally responsible choices, the Enviro EF3 stands out as a leading option in the electric vehicle market.