Enviro EF3 200F 93C high limit temperature sensor has tripped, Stove will not shut off

Page 30

Troubleshooting

8. The 200°F (93°C) high limit temperature sensor has tripped.

●Reset the sensor and determine the cause - was it convection blower or 160°F (71°C) temperature sensor failure? Bypass the 160°F (71°C) sensor. Does the convection blower come on high? If no, replace the blower.

9. The stove will not shut off.

●If the unit will not shut off, ensure that the thermostat (if equipped) is turned down below the room temperature (thermostat mode in the ON / OFF position).

●Disconnect one of the brown wires from the exhaust temperature sensor. If the unit continues to operate, contact your local dealer for service.

◊Check the connections to the 140°F (60°C) temperature sensor, start-up switch and the start-up timer against the wiring diagram.

◊Check the 140°F (60°C) temperature sensor by removing one of the brown wires from the sensor. The unit should shut down right away as long as the start button was not pressed within 15 minutes of this test. If the stove shuts down within fifteen (15) minutes, replace the 140°F (60°C) sensor. If the stove does not shut down within fifteen (15) minutes, test the switch.

◊To test the switch, the stove must be cold. Pull the plug, then plug the stove back in. If it fails to start, replace the switch.

10. The stove keeps going out

If the stove goes out and leaves fresh unburned pellets or cigarette-like ashes in the burn pot liner, the fire is going out before the stove shuts off.

● Check to see that the Slider / Damper is in the correct position.

◊ Turn the Dial-a-Fire up slightly (poor quality pellets will require slightly higher settings).

If the stove goes out and there are partially burned pellets left in the burn pot liner, the stove has shut down due to a lack of air, exhaust temperature, or power failure.

●Adjust the Slider / Damper.

●Check to see if the stove needs a more complete cleaning.

●Did the power go out?

●Contact your local Dealer for service.

◊ Turn the Dial-a-Fire up slightly (poor quality pellets will require slightly higher settings).

If the stove goes out and there are no pellets in the liner, the auger is stopping.

●See “The auger motor will not function normally” and “The exhaust blower will not function normally.”

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents EF3 Table of Contents Introduction I. Pellet StandardsStore pellets at least 36 1 m away from the pellet stove USE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel Reasons WHY the Unit Overheated Operating InstructionsSpecial Notes Dial-A-Fire control panel Burn POT and Liner 2-3 days Routine Cleaning and MaintenanceTools Required to Clean Unit Inside Firebox weeklyHeat Exchanger Tubes 2-3 days Removal of the firebox backing for bi-annual cleaningFreestanding ASH PAN Fresh AIR Intake seasonPost Season CLEAN-UP Cleaning Plated SurfacesBrick Panel Installation Screws to take out to remove stove from palletDimensions of EF3 Freestanding Minimum Alcove width Inches 91 cm Minimum Alcove height Or from the outside of the pedestal for the FPI or BIH EF3 Built-In Heater recommended FramingVent surfaces can Install Vent AT Clearances Specified by Venting Manufacturer Fresh Air Intake Place the appliance 15 37.5 cm Is the recommended installation set up Inside Vertical Installation Outside Vertical Installation Freestanding hearth mount installation overview Connect a tee or 90 degree Control panel see Figure Removal Corner brackets for TrimTube scrapper rod Placement Do not TroubleshootingStove will not operate when hot. Check the hopper for fuel What to do ifExhaust motor will not function normally Dial-a-fire has no effect on the fire Timer Control Only Auger motor will not function normallyPotentiometer Readings 200F 93C high limit temperature sensor has tripped Stove will not shut offStove keeps going out Wiring Diagram Timer ControlParts List Reference Description Part NumberParts List Options Parts Diagram Components EF3 Steel Components Warranty To the DistributorFor the do-it-yourself Individual Installation Data Sheet Name of Owner Address
Related manuals
Manual 43 pages 19.26 Kb

EF3 specifications

The Enviro EF3 is an innovative and eco-friendly vehicle that is transforming the landscape of sustainable transportation. With a focus on efficiency, performance, and environmental responsibility, the EF3 represents a significant leap forward in automotive technology.

One of the standout features of the Enviro EF3 is its advanced electric powertrain. This vehicle is equipped with a state-of-the-art electric motor that provides impressive torque and acceleration while remaining silent and efficient. The electric motor is powered by a high-capacity lithium-ion battery pack, which can be charged quickly and has a long lifespan. This allows for extended driving ranges, making the EF3 ideal for both urban commuting and longer journeys.

The EF3 also incorporates regenerative braking technology, which captures energy that would otherwise be lost during braking. This innovative feature helps to recharge the battery while enhancing overall energy efficiency. As a result, drivers can enjoy longer trips and reduced charging frequency, while also minimizing the vehicle's overall environmental impact.

In terms of design, the Enviro EF3 boasts a sleek, aerodynamic profile that not only looks modern but also contributes to its overall efficiency. The vehicle's exterior is crafted using lightweight materials, which enhance performance and help to maximize range. Additionally, the spacious interior is designed with comfort and sustainability in mind. Eco-friendly materials are used throughout the cabin, ensuring that the EF3 remains a green choice even inside the vehicle.

Connectivity is another vital characteristic of the Enviro EF3. Equipped with the latest infotainment and navigation technologies, the vehicle offers seamless integration with smartphones and other devices. This feature allows drivers to access real-time traffic updates, manage charging schedules, and even control various vehicle settings from their mobile devices.

Safety is prioritized in the design of the EF3, with advanced driver-assistance systems (ADAS) that include features such as adaptive cruise control, lane-keeping assist, and collision avoidance technology. These systems work together to enhance driver confidence and ensure a safe driving experience.

In conclusion, the Enviro EF3 represents the future of sustainable transportation. With its electric powertrain, advanced technologies, aerodynamic design, and a strong focus on safety and connectivity, the EF3 is a versatile and eco-friendly vehicle that meets the demands of modern drivers while contributing to a healthier planet. As more consumers seek environmentally responsible choices, the Enviro EF3 stands out as a leading option in the electric vehicle market.
Top Page Image Contents