Enviro EF2 owner manual Or from the outside of the pedestal for the FPI or BIH

Page 14

Installation

CLEARANCES TO COMBUSTIBLES - BUILT-IN HEATER:

Refer to Figures 11 and 12.

 

 

Side wall to unit

- 8 inches

(20.3 cm)

Mantel projection

- 10 inches

(25.4 cm)

Mantel to top of unit

- 8 inches

(20.3 cm)

Top facing to unit

- 8 inches

(20.3 cm)

Side facing to unit

- 6 inches

(15.2 cm)

Floor protection

- 6 inches

(15.2 cm)

(on either side and to the front must be protected

by non-combustible material)

 

Sides and rear walls to standoffs: - 0 inches

(0 cm)

Recess depth:

- 11 inches

(30 cm)

 

33"

 

(84 cm)

 

12"

 

(30.5 cm)

 

30"

 

(76 cm)

 

6"

 

(15 cm)

6"

Floor Protection

(15 cm)

Figure 12: EF2 Built-In Heater recommended

framing.

PEDESTAL INSTALLATION:

The all models comes with a pedestal that has to be attached prior to installation:

• Remove the unit from the box

• Remove the freestanding pedestal from the box. Remove the FPI or BIH pedestal from the hopper.

Figure 14: Fireplace Insert Pedestal.

Figure 13: Freestanding Pedestal.

• Place the unit on its back on the pallet.

• Back the four (4) 5/16” hex head screws in the base off three (3) to four (4) full turns.

• Align the keyholes in the pedestal with the screws, lock into place.

Secure the two (2) pieces by tightening the four (4) screws from the inside of the pedestal for the freestanding

or from the outside of the pedestal for the FPI or BIH.

Figure 15: Built-In Heater Pedestal.

14

Image 14
Contents EF2 Table of Contents Store pellets at least 36 1 m away from the pellet stove IntroductionI. Pellet Standards USE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel Special Notes Reasons WHY the Unit OverheatedOperating Instructions Special Notes Burn POT and Liner 2-3 days Routine Cleaning and MaintenanceTools Required to Clean Unit Inside Firebox 2-3 daysFireplace Insert and BUILT-IN Heater ASH PAN Not Place Unburned or RAW Pellet Fuel in ASH PANFreestanding ASH PAN Brick Panel Post Season CLEAN-UPCleaning Plated Surfaces Installation Screws to take out to remove stove from palletDimensions of EF2 Freestanding Minimum Alcove width Inches 91 cm Minimum Alcove height Or from the outside of the pedestal for the FPI or BIH EF2 Built-In Heater recommended FramingArea Under Sundeck Fresh AIR Intake ExhaustFreestanding Fireplace Insert Built-In Heater Fresh Air Intake Unit on it Locate the center of the exhaust Is the recommended installation set up Inside Vertical Installation Install the hearth pad Freestanding hearth mount installation overview Elbow to the exhaust pipe This unit includes a 3 75 mm pedestal Corner Brackets Removal Side surround panel swings forwardStove will not light TroubleshootingStove will not start Convection blower will not function normally Stove will not function in the Auto mode when hotExhaust motor will not function normally Auger motor will not function normally Stove will not shut off Dial-a-fire has no effect on the firePotentiometer Readings Stove keeps going outWiring Diagram Parts List Fireplace Insert Stove Top Parts List Parts List Options ComponentsDPartsiagram Parts Diagram Steel Warranty To the DealerWarranty Installation Data Sheet Name of Owner Address

EF2 specifications

The Enviro EF2 is a cutting-edge electric vehicle specifically designed for urban environments, combining eco-friendliness with advanced technology. This vehicle stands out in the burgeoning electric vehicle market due to its unique blend of functionality, efficiency, and sustainability.

One of the main features of the Enviro EF2 is its remarkable range. With a fully charged battery, it can travel up to 300 miles, making it ideal for both daily commutes and longer journeys. The vehicle is equipped with a high-capacity lithium-ion battery pack, which not only extends its range but also ensures quick charging times. Thanks to fast-charging capabilities, the battery can be recharged to 80% in just 30 minutes, allowing drivers to minimize downtime and maximize productivity.

The Enviro EF2's performance is further enhanced by its advanced electric drive system. This system delivers impressive torque and acceleration while maintaining a quiet and smooth driving experience. The vehicle boasts a top speed of 120 mph, enabling drivers to merge seamlessly into highway traffic while enjoying the benefits of electric driving.

In terms of design, the Enviro EF2 embodies modern aesthetics with a sleek and aerodynamic exterior. The interior is equally impressive, featuring a spacious cabin lined with sustainable materials that provide both comfort and style. Smart seating configurations make the vehicle adaptable for families or cargo, with ample storage solutions to accommodate various needs.

Technologies incorporated into the Enviro EF2 include state-of-the-art infotainment systems, offering seamless connectivity through smartphone integration. The vehicle also includes advanced driver-assistance systems, enhancing safety through features such as adaptive cruise control, lane-keeping assist, and automatic emergency braking. These technologies work together to create a more secure driving experience.

The Enviro EF2 emphasizes sustainability beyond just its electric powertrain. The manufacturing process incorporates eco-friendly practices, and the materials used in production are chosen for their minimal environmental impact. This makes the vehicle a responsible choice for environmentally-conscious consumers.

In conclusion, the Enviro EF2 represents a significant advancement in electric vehicle technology. With its impressive range, rapid charging capabilities, performance features, and sustainable design, it meets the evolving needs of urban drivers, making it a compelling choice in the electric vehicle landscape. The Enviro EF2 is not just a vehicle; it is a forward-thinking solution for a cleaner, greener future.