Enviro EF2 owner manual Stove will not function in the Auto mode when hot

Page 28

Troubleshooting

3. The stove will not function in the “AUTO” mode when hot.

wIf the unit fails to operate, by-pass the auto side of the switch by inserting a jumper wire between the dual black wires and the dual brown wires located on the back of the switch. Plug the stove back in. If the stove operates, replace the switch.

wCheck the hopper for fuel.

wIncorrect air damper setting - Excessive air may consume the fire too quickly before the next drop of fuel, leaving completely unburned fuel in the burn pot liner. Insufficient air will cause build up, further restricting the air flow through the Burn Pot Liner. This in turn will cause the fuel to burn cold and very slowly. Fuel may build up and smother the fire. (NOTE: Unit may require a change to the vent system or installation of fresh air to correct Air to Fuel ratio problems).

wCombustion Blower failure - The Combustion Blower is not turning fast enough to generate the proper vacuum in the fire box. Visual Check – is the blower motor turning?

wCheck Vacuum levels in the exhaust channel by bypassing the Vacuum Switch, then remove the Vacuum hose from Vacuum Switch. Check exhaust vacuum readings by placing the open end of the Vacuum Hose on a Magnahelic Gauge (readings must be above 0.10” W.C. on low fire).

Note: If the motor fails to reach a 0.10” W.C. reading, then replace the Combustion Blower.

wPoor Quality Fuel – Insufficient energy in the fuel to produce enough heat to keep the stove burning or operational.

wExhaust Temperature Sensor failure – Bypass sensor located on Exhaust Blower. If stove now operates properly, the unit may require cleaning or a new sensor. Contact your local dealer for service.

wThe unit may require cleaning. Contact your local dealer for service.

4. The exhaust motor will not function normally.

wOpen the left side access panel; check all connections against the wiring diagram.

wIf all the connections are verified and the exhaust blower does not function at all, tap lightly on the exhaust blower’s motor end cap, this may loosen a tight motor.

wApply 115 V AC directly to the exhaust blower. If the motor does not run, replace the blower.

wIf the motor runs, have your dealer check the harness.

wContact your local dealer for service.

5. The convection blower will not function normally.

wCheck all the connections between the controller, switch, and the convection blower against the wiring diagram.

wIf the convection motor will not run, apply 115 V AC to the motor directly. If the motor runs, replace the fan controller. If the motor does not run, the convection blower has failed. Replace the blower.

wIf the convection blower runs on high at all times (no control with the fan controller), check the connections from the 160°F (71°C) sensor (located on the upper left side of the firewall) and convection fan controller to the blower. Disconnect one of the wires from the sensor; if control of the convection blower returns to the fan controller, replace the sensor.

wIf the motor is still on high, re-connect the sensor and replace the convection fan controller.

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents EF2 Table of Contents I. Pellet Standards IntroductionStore pellets at least 36 1 m away from the pellet stove USE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel Operating Instructions Reasons WHY the Unit OverheatedSpecial Notes Special Notes Routine Cleaning and Maintenance Tools Required to Clean UnitBurn POT and Liner 2-3 days Inside Firebox 2-3 daysFreestanding ASH PAN Not Place Unburned or RAW Pellet Fuel in ASH PANFireplace Insert and BUILT-IN Heater ASH PAN Cleaning Plated Surfaces Post Season CLEAN-UPBrick Panel Installation Screws to take out to remove stove from palletDimensions of EF2 Freestanding Minimum Alcove width Inches 91 cm Minimum Alcove height Or from the outside of the pedestal for the FPI or BIH EF2 Built-In Heater recommended FramingArea Under Sundeck Freestanding Fireplace Insert Built-In Heater ExhaustFresh AIR Intake Fresh Air Intake Unit on it Locate the center of the exhaust Is the recommended installation set up Inside Vertical Installation Install the hearth pad Freestanding hearth mount installation overview Elbow to the exhaust pipe This unit includes a 3 75 mm pedestal Corner Brackets Removal Side surround panel swings forwardStove will not start TroubleshootingStove will not light Exhaust motor will not function normally Stove will not function in the Auto mode when hotConvection blower will not function normally Auger motor will not function normally Dial-a-fire has no effect on the fire Potentiometer ReadingsStove will not shut off Stove keeps going outWiring Diagram Parts List Fireplace Insert Stove Top Parts List Parts List Options ComponentsDPartsiagram Parts Diagram Steel Warranty To the DealerWarranty Installation Data Sheet Name of Owner Address

EF2 specifications

The Enviro EF2 is a cutting-edge electric vehicle specifically designed for urban environments, combining eco-friendliness with advanced technology. This vehicle stands out in the burgeoning electric vehicle market due to its unique blend of functionality, efficiency, and sustainability.

One of the main features of the Enviro EF2 is its remarkable range. With a fully charged battery, it can travel up to 300 miles, making it ideal for both daily commutes and longer journeys. The vehicle is equipped with a high-capacity lithium-ion battery pack, which not only extends its range but also ensures quick charging times. Thanks to fast-charging capabilities, the battery can be recharged to 80% in just 30 minutes, allowing drivers to minimize downtime and maximize productivity.

The Enviro EF2's performance is further enhanced by its advanced electric drive system. This system delivers impressive torque and acceleration while maintaining a quiet and smooth driving experience. The vehicle boasts a top speed of 120 mph, enabling drivers to merge seamlessly into highway traffic while enjoying the benefits of electric driving.

In terms of design, the Enviro EF2 embodies modern aesthetics with a sleek and aerodynamic exterior. The interior is equally impressive, featuring a spacious cabin lined with sustainable materials that provide both comfort and style. Smart seating configurations make the vehicle adaptable for families or cargo, with ample storage solutions to accommodate various needs.

Technologies incorporated into the Enviro EF2 include state-of-the-art infotainment systems, offering seamless connectivity through smartphone integration. The vehicle also includes advanced driver-assistance systems, enhancing safety through features such as adaptive cruise control, lane-keeping assist, and automatic emergency braking. These technologies work together to create a more secure driving experience.

The Enviro EF2 emphasizes sustainability beyond just its electric powertrain. The manufacturing process incorporates eco-friendly practices, and the materials used in production are chosen for their minimal environmental impact. This makes the vehicle a responsible choice for environmentally-conscious consumers.

In conclusion, the Enviro EF2 represents a significant advancement in electric vehicle technology. With its impressive range, rapid charging capabilities, performance features, and sustainable design, it meets the evolving needs of urban drivers, making it a compelling choice in the electric vehicle landscape. The Enviro EF2 is not just a vehicle; it is a forward-thinking solution for a cleaner, greener future.
Top Page Image Contents