Enviro EF2 owner manual Special Notes

Page 7

Operating Instructions

OPERATING YOUR PELLET STOVE:

1.Check and fill hopper with pellets.

2.Make sure unit is plugged into a working outlet.

3.Switch the power on by pushing the ROCKER SWITCH to the MANUAL position.

4.Turn KNOB B to the 12 o’clock position. (Lower grade pellets may need a higher setting on the feed rate). NOTE: Unit will take longer to light if the hopper has been completely emptied or is the first fire up.

5.Approximately fifteen (15) minutes after the fire was lit, the GREEN LIGHT should come on. When the GREEN LIGHT comes on, push the ROCKER SWITCH to the AUTO position. Now the stove will shut-off automatically if the fire goes out.

6.Wait until the fire is established, then turn KNOB B to the desired heat output. The stove may not be able to burn in the BLUE ZONE if poor quality wood pellets are being used. Adjust the slider-damper to the appropriate setting (see

“SLIDER/DAMPER SETTING” section.

 

Figure 3: Dial-A-Fire control panel.

KNOB “A”: Fan Controller. By adjusting the knob you will vary the rate of airflow into the room by varying the speed of the convection blower. When you first start the stove, it should be placed in the “OFF” position in order to heat the unit as quickly as possible. Once the room has come up to temperature, the control may be set to a comfortable level. *Note: The convection blower may cycle to high automatically depending on the setting of KNOBS A and B. This is a normal safety feature of the unit.

KNOB “B”: Dia-A-Fire Heat Output Knob. This knob controls the amount of heat output. The dial has a scale with the blue zone representing the coolest setting of the stove, and the red zone representing the hottest setting. The scale on knob “B” represents a range, not exact at times or fuel quantities.

Wood pellets of differing quality may affect the performance of the stove. If the stove has trouble operating at either end of its range, turn the heat output knob back slightly.

TURNING YOUR PELLET STOVE OFF:

The AUTO/MANUAL SWITCH must be in the AUTO position during operation. To turn the stove off, simply turn the HEAT OUTPUT knob (KNOB B) counter-clockwise until the knob clicks to the “OFF” position. This will stop the feed of pellets. The blowers will continue to run and cool the stove.

SPECIAL NOTES:

If the stove is left in the manual mode after the green light comes on, the auger will continue to feed pellets. Pellets may over flow the burn-pot after the fire goes out and also re-light.

The scale on KNOB B represents a range, not exact times. Wood pellets of differing quality may effect the performance and/or the heat output of the stove. If the stove has trouble operating at the end of its range, adjust the heat output knob back slightly.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents EF2 Table of Contents I. Pellet Standards IntroductionStore pellets at least 36 1 m away from the pellet stove USE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel Operating Instructions Reasons WHY the Unit OverheatedSpecial Notes Special Notes Inside Firebox 2-3 days Routine Cleaning and MaintenanceTools Required to Clean Unit Burn POT and Liner 2-3 daysFreestanding ASH PAN Not Place Unburned or RAW Pellet Fuel in ASH PANFireplace Insert and BUILT-IN Heater ASH PAN Cleaning Plated Surfaces Post Season CLEAN-UPBrick Panel Screws to take out to remove stove from pallet InstallationDimensions of EF2 Freestanding Minimum Alcove width Inches 91 cm Minimum Alcove height EF2 Built-In Heater recommended Framing Or from the outside of the pedestal for the FPI or BIHArea Under Sundeck Freestanding Fireplace Insert Built-In Heater ExhaustFresh AIR Intake Fresh Air Intake Unit on it Locate the center of the exhaust Is the recommended installation set up Inside Vertical Installation Install the hearth pad Freestanding hearth mount installation overview Elbow to the exhaust pipe This unit includes a 3 75 mm pedestal Corner Brackets Side surround panel swings forward RemovalStove will not start TroubleshootingStove will not light Exhaust motor will not function normally Stove will not function in the Auto mode when hotConvection blower will not function normally Auger motor will not function normally Stove keeps going out Dial-a-fire has no effect on the firePotentiometer Readings Stove will not shut offWiring Diagram Parts List Fireplace Insert Stove Top Parts List Parts List Options ComponentsDPartsiagram Parts Diagram Steel To the Dealer WarrantyWarranty Name of Owner Address Installation Data Sheet

EF2 specifications

The Enviro EF2 is a cutting-edge electric vehicle specifically designed for urban environments, combining eco-friendliness with advanced technology. This vehicle stands out in the burgeoning electric vehicle market due to its unique blend of functionality, efficiency, and sustainability.

One of the main features of the Enviro EF2 is its remarkable range. With a fully charged battery, it can travel up to 300 miles, making it ideal for both daily commutes and longer journeys. The vehicle is equipped with a high-capacity lithium-ion battery pack, which not only extends its range but also ensures quick charging times. Thanks to fast-charging capabilities, the battery can be recharged to 80% in just 30 minutes, allowing drivers to minimize downtime and maximize productivity.

The Enviro EF2's performance is further enhanced by its advanced electric drive system. This system delivers impressive torque and acceleration while maintaining a quiet and smooth driving experience. The vehicle boasts a top speed of 120 mph, enabling drivers to merge seamlessly into highway traffic while enjoying the benefits of electric driving.

In terms of design, the Enviro EF2 embodies modern aesthetics with a sleek and aerodynamic exterior. The interior is equally impressive, featuring a spacious cabin lined with sustainable materials that provide both comfort and style. Smart seating configurations make the vehicle adaptable for families or cargo, with ample storage solutions to accommodate various needs.

Technologies incorporated into the Enviro EF2 include state-of-the-art infotainment systems, offering seamless connectivity through smartphone integration. The vehicle also includes advanced driver-assistance systems, enhancing safety through features such as adaptive cruise control, lane-keeping assist, and automatic emergency braking. These technologies work together to create a more secure driving experience.

The Enviro EF2 emphasizes sustainability beyond just its electric powertrain. The manufacturing process incorporates eco-friendly practices, and the materials used in production are chosen for their minimal environmental impact. This makes the vehicle a responsible choice for environmentally-conscious consumers.

In conclusion, the Enviro EF2 represents a significant advancement in electric vehicle technology. With its impressive range, rapid charging capabilities, performance features, and sustainable design, it meets the evolving needs of urban drivers, making it a compelling choice in the electric vehicle landscape. The Enviro EF2 is not just a vehicle; it is a forward-thinking solution for a cleaner, greener future.
Top Page Image Contents