Enviro EF2 owner manual Introduction, I. Pellet Standards

Page 3

Introduction

PELLET QUALITY:

Pellet quality is important, please read the following:

Your enviro pellet stove has been designed to burn wood pellets only. Do not use any other type of fuel, as this will void any warranties stated in this manual.

The performance of your pellet stove is greatly affected by the type and quality of wood pellets being burned. As the heat output of various quality wood pellets differs, so will the performance and heat output of the pellet stove.

CAUTION: It is important to select and use only pellets that are dry and free of dirt or any impurities such as high salt content. Dirty fuel will adversely affect the operation and performance of the unit and will void the warranty. The Pellet Fuel Industries (P.F.I.) has established standards for wood pellet manufacturers. We recommend the use of pellets that meet or exceed these standards. Ask your dealer for a recommended pellet type.

P.F.I. PELLET STANDARDS:

Fines (fine particles)

1% maximum through a 1/8” screen

Bulk Density

40 pound per cubic foot minimum

Size

1⁄4” to 5/16” diameter 1⁄2 – 11⁄2” long maximum

Ash Content

1% maximum (Premium grade)

..................

3% maximum (Standard grade)

Moisture Content

8% maximum

Heat Content

approximately 8200 Btu per pound minimum

ASH: The ash content of the fuel and operation of your stove will directly determine the frequency of cleaning. The use of high ash fuels may result in the stove needing to be cleaned daily. A low ash fuel may allow longer intervals between cleaning.

CLINKERING: [clinkers are silica (sand) or other impurities in the fuel that will form a hard mass during the burning process]. This hard mass will block the air flow through the Burn Pot Liner and affect the performance of the stove. Any fuel, even approved types, may tend to clinker. Check the Burn-Pot Liner daily to ensure that the holes are not blocked with clinkers. If they become blocked, remove the liner (when the unit is cold) and clean/scrape the clinkers out. Clean the holes with a small pointed object if required. Refer to the section Routine Cleaning and Maintenance.

PELLET FEED RATES: Due to different fuel densities and sizes, pellet feed rates may vary. This may require an adjustment to the slider damper setting or to the auger feed trim setting on low.

Since Sherwood Industries Ltd. has no control over the quality of pellets that you use, we assume no liability for your choice in wood pellets.

Store pellets at least 36” (1 m) away from the pellet stove.

RATING LABEL LOCATION:

Freestanding: The rating label is located on the inside of the hopper lid.

Insert: The rating label is located on the hopper cover.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents EF2 Table of Contents Introduction I. Pellet StandardsStore pellets at least 36 1 m away from the pellet stove USE of Cordwood is Prohibited by LAW Keep ASH PAN Free of RAW Fuel Reasons WHY the Unit Overheated Operating InstructionsSpecial Notes Special Notes Inside Firebox 2-3 days Routine Cleaning and MaintenanceTools Required to Clean Unit Burn POT and Liner 2-3 daysNot Place Unburned or RAW Pellet Fuel in ASH PAN Freestanding ASH PANFireplace Insert and BUILT-IN Heater ASH PAN Post Season CLEAN-UP Cleaning Plated SurfacesBrick Panel Screws to take out to remove stove from pallet InstallationDimensions of EF2 Freestanding Minimum Alcove width Inches 91 cm Minimum Alcove height EF2 Built-In Heater recommended Framing Or from the outside of the pedestal for the FPI or BIHArea Under Sundeck Exhaust Freestanding Fireplace Insert Built-In HeaterFresh AIR Intake Fresh Air Intake Unit on it Locate the center of the exhaust Is the recommended installation set up Inside Vertical Installation Install the hearth pad Freestanding hearth mount installation overview Elbow to the exhaust pipe This unit includes a 3 75 mm pedestal Corner Brackets Side surround panel swings forward RemovalTroubleshooting Stove will not startStove will not light Stove will not function in the Auto mode when hot Exhaust motor will not function normallyConvection blower will not function normally Auger motor will not function normally Stove keeps going out Dial-a-fire has no effect on the firePotentiometer Readings Stove will not shut offWiring Diagram Parts List Fireplace Insert Stove Top Parts List Parts List Options ComponentsDPartsiagram Parts Diagram Steel To the Dealer WarrantyWarranty Name of Owner Address Installation Data Sheet

EF2 specifications

The Enviro EF2 is a cutting-edge electric vehicle specifically designed for urban environments, combining eco-friendliness with advanced technology. This vehicle stands out in the burgeoning electric vehicle market due to its unique blend of functionality, efficiency, and sustainability.

One of the main features of the Enviro EF2 is its remarkable range. With a fully charged battery, it can travel up to 300 miles, making it ideal for both daily commutes and longer journeys. The vehicle is equipped with a high-capacity lithium-ion battery pack, which not only extends its range but also ensures quick charging times. Thanks to fast-charging capabilities, the battery can be recharged to 80% in just 30 minutes, allowing drivers to minimize downtime and maximize productivity.

The Enviro EF2's performance is further enhanced by its advanced electric drive system. This system delivers impressive torque and acceleration while maintaining a quiet and smooth driving experience. The vehicle boasts a top speed of 120 mph, enabling drivers to merge seamlessly into highway traffic while enjoying the benefits of electric driving.

In terms of design, the Enviro EF2 embodies modern aesthetics with a sleek and aerodynamic exterior. The interior is equally impressive, featuring a spacious cabin lined with sustainable materials that provide both comfort and style. Smart seating configurations make the vehicle adaptable for families or cargo, with ample storage solutions to accommodate various needs.

Technologies incorporated into the Enviro EF2 include state-of-the-art infotainment systems, offering seamless connectivity through smartphone integration. The vehicle also includes advanced driver-assistance systems, enhancing safety through features such as adaptive cruise control, lane-keeping assist, and automatic emergency braking. These technologies work together to create a more secure driving experience.

The Enviro EF2 emphasizes sustainability beyond just its electric powertrain. The manufacturing process incorporates eco-friendly practices, and the materials used in production are chosen for their minimal environmental impact. This makes the vehicle a responsible choice for environmentally-conscious consumers.

In conclusion, the Enviro EF2 represents a significant advancement in electric vehicle technology. With its impressive range, rapid charging capabilities, performance features, and sustainable design, it meets the evolving needs of urban drivers, making it a compelling choice in the electric vehicle landscape. The Enviro EF2 is not just a vehicle; it is a forward-thinking solution for a cleaner, greener future.
Top Page Image Contents